Home

Extron electronic 3G User's Manual

1. 7 Optional Daisy chain additional FOX 3G devices Connect another FOX 3G DVC or a FOX 3G HD SDI to the Buffered Loop Through Tx port of the input connector Up to three devices can be daisy chained from this port 8 Connect power to the FOX 3G DVC by plugging a standard IEC power cord provided from a 100 to 240 VAC 50 60 Hz power source into the power receptacle Front Panel Features oa ee USB Config port FE NEXT LCD screen 37 3 Menu button Extron FOX 3G DVC Next button DIGITAL VIDEO CONVERTER Adjust knobs Configuring the FOX 3G DVC Using the Front Panel Menu selections are displayed on the front panel LCD screen To use any menu press the Menu button repeatedly until the desired menu is displayed see the menu flow diagram at lower right Press the Next button repeatedly until the desired submenu appears Rotate an Adjust knob to select an item from a submenu To return to the main menu at any time press Menu After 30 seconds of inactivity the screen displays the default cycle 1 From the Output Config submenus use the Adjust knobs to select the output signal betun Defaul type and the sync polarity to match the requirements of the display device Oye 2 From the Advanced Config menu Test Pattern submenu select the Crop Crosshatch Colorbars and Grayscale test patterns to confirm that the settings of the display rs device are correct OUTPUT CONFIG Menu AUDIO CONFIG m
2. As n wz Extron Electronics To ov INTERFACING SWITCHING AND CONTROL ori FOX 3G DVC e Setup Guide The Extron FOX 3G DVC receives fiber optic SD SDI HD SDI and 3G SDI serial digital video signals over a single fiber and converts them to DVI D and analog RGB or component video It is compatible with the FOX 3G HD SDI Fiber Optic Extender as well as FOX Series distribution amplifiers switchers and matrix switchers The FOX 3G DVC features extraction of embedded AES3 audio RS 232 and USB serial control and a fiber optic input loop through that allows multiple FOX 3G DVC and FOX 3G HD SDI units to be daisy chained The FOX 3G DVC is compliant with SMPTE 259M 292M 424M and ITU digital video standards The RGB output can be set for RGBHV RGBS and RGsB Bi level or tri level sync can be selected when the unit is set for component video output The FOX 3G DVC MM supports multimode fiber at 850 nm for moderate transmission distances up to 500 m 1 640 feet The FOX 3G DVC SM supports singlemode fiber at 1310 nm for long distances of up to 30 km 18 75 miles AC power connector Tx port buffered loop through Rx port Link LED DVI D output connector RGB YUV output connector 100 240V 0 3A MAX BUFFERED LOOP THROUGH Audio output connector Installation Steps RS 232 connector 1 Disconnect power from all equipment 2 Optional Mount the unit to a rack or furniture 3 Connect
3. enu ADVANCED CONFIG EXIT MENU PRESS NEXT NOTE Test pattern timings are based on the incoming SDI signals and are not displayed if an active signal is not present 3 Use the Audio Config submenus to configure the audio as desired Supported Input Resolutions NOTE The output resolution always matches the input resolution Simple Instruction Set SIS Commands When setting up the FOX 3G DVC you can issue SIS commands from your computer via RS 232 or USB as an alternative to the front panel controls See the FOX 3G DVC Series User Guide for a complete list of available SIS commands ASCII command Response Command Host to Converter Converter to Host Additional Description Mute video 1B Vmt1 lt e4 Mute the video output Unmute video B Vmt 4 Display the video output Mute audio 1Z Amt1 lt Mute the audio output Unmute audio QZ Amt lt Unmute the audio output Enable lock executive mode 1X Exeie Lock all front panel functions Disable lock mode OX Exe 4 Enable all front panel functions 2 2011 Extron Electronics All rights reserved www extron com 68 1518 51 Rev C 09 11
4. the video input Connect an SD SDI HD SDI or 3G SDI source to the SDI HD SDI Rx port of the fiber optic LC input connector in the rear panel illustration above 4 Connect the video output Connect a display or other output device to the DVD D digital video connector or to the RGB R Y Y B Y analog RGB RGBHV RGBS and RGsB or YUV component video connector 5 Connect a control device Connect a host device such as a computer or touchpanel control system to one or both of the following DVC ports to configure and control the DVC via Simple Instruction Set SIS commands e RS 232 port rear panel Connect a host device s to the Tx Rx and ground pins of this 5 pole captive screw connector The first and second pins of this connector are not used The default protocol for this port is 9600 baud 1 stop bit no parity 8 data bits and no flow control e Config port front panel Connect a USB cable USB A to USB mini B between a USB port on your computer and this port on the front panel illustration on the next page 6 Connect the audio output Connect an amplifier or other audio output device to the 5 pole captive screw audio connector on the rear panel illustration as shown below 5 mm MAX 5 Do not tin the wires Balanced Audio Output Unbalanced Audio Output CAUTION For unbalanced audio connect the sleeves to the ground contact DO NOT connect them to negative contacts

Extron electronic 3G User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents