Euro-Pro PURSUIT EP724 User's Manual
Contents
1. Bagless Cyclonic Canister OWNER S MANUAL Model EP724 120V 60Hz 10 3 Amps For information or assistance EURO PRO Operating LLC 94 Main Mill Street Door 16 Plattsburgh NY 12901 www sharkvac com EURO PROX IMPORTANT SAFETY INSTRUCTIONS When using your Bagless Cyclonic Canister vacuum basic safety precautions should always be observed including the following WARNING To reduce the risk of fire electrical shock or injury 1 10 11 12 Do not leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use To reduce the risk of electric shock do not use outdoors or on wet surfaces Do not handle plug or vacuum cleaner with wet hands Do not allow children to use as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug Do not use vacuum cleaner if it has been dropped damaged left outdoors or dropped into water Return appliance to EURO PRO Operating LLC for examination repair or adjustment Do not pull or carry by cord Do not use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Keep hair loose clothing fingers and all parts of body away2. you allow it to dry COMPLETELY before using it again We recommend 24 hours to air dry DO NOT DRY IN DRYER The HEPA Dust Cup Filter should be replaced every 3 months or sooner depending on amount of use IMPORTANT The Pre Motor Filter Pre Filter and Post Motor Filter should be replaced every 6 months or sooner if required All filters should be checked regularly for signs of damage preferable after each cleaning task The filters must be replaced immediately if they become damaged Always disconnect the vacuum from the electrical outlet when checking the filters Important This vacuum cleaner is equipped with a motor protective thermostat If for some reason your vacuum overheats the thermostat will automatically turn the unit off Should this occur unplug the vacuum from the wall outlet and turn off the switch Empty the dust cup TapClean the dust cup filter and check for blockages in hose and suction inlet Allow the unit to cool for a minimum of 45 minimum prior to restarting the unit To restart re plug the vacuum into the wall socket and turn the switch back on 10 PROBLEM SOLVING This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory If a minor problem occurs it usually can be solved quite easily when the cause is found Therefore this checklist is provided for your convenience PROBLEM POSSIBLE CAUSE POSSIBLE 1 Not firmly plugged in 2
3. e Push the Power On Off button to the Off position and disconnect the power cord from the wall outlet e Open the dust cup cover and remove the dust cup being careful not to press on the trap door release button e Remove the HEPA filter and hold the tab that is on the top of the filter and pull until the filter cover snaps off e Rinse pre filter in lukewarm water let dry completely Do not use a washing machine to rinse the filter Do not use a hair dryer to dry it Air dry only e Replace only when the pre filter is completely dry replace into HEPA filter and snap the cover back in place l A Pre Filter Cover Assembling Your Vacuum Cleaner Note Always remove the power plug from the wall outlet before assembling or removing accessories 1 Attaching the Flexible Hose into the Vacuum Connect the flexible hose into the hose connector inlet Push in until you hear a click indicating it is in its locked position 2 Fitting the Chrome Telescopic Tube to the Curved Wand Hose Extension Push the chrome telescopic tube into the curved wand hose extension as shown in the illustration below _ _ J a 3 Extending the Chrome Telescopic Tube Push forward on the plastic button and pull the inner chrome tube outward a a Plastic Button 4 Fitting the Floor to Carpet Brush or the Air Driven Turbo Brush to the Telescopic Tube Push the telescopic tube into the desired flo
4. from openings and moving parts Do not pick up hot coals cigarette butts matches or any hot smoking or burning objects Do not pick up hard or sharp objects such as glass nails screws coins etc Do not use without filters in place Turn off all controls before plugging or unplugging vacuum cleaner 13 14 15 16 17 18 19 20 21 22 23 24 25 Use extra care when vacuuming on stairs Do not pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapor Do not pick up toxic material chlorine bleach ammonia drain cleaner etc Do not use in an enclosed space filled with vapors given off by oil based paints paint thinner moth proofing substances flammable dust or other explosive or toxic vapors Always unplug this appliance before connecting or disconnecting vacuum hose Always hold the plug when rewinding the power cord Do not allow plug to whip when rewinding Use only on dry indoor surfaces Do not use for any purpose other than described in this user s guide Use only extension cords UL or cUL rated at 15 amperes Extension cords rated for less amperage may overheat Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over Do not put any objects into openings Do not use with any opening blocked Keep free of dust lint hair and anything else that may reduc
5. let dry completely Do not use a washing machine to rinse the filter Do not use a hair dryer to dry it Air dry only e When filter is completely dry replace pre motor filter back into the unit and close the dust cup cover s Ee Pre Motor i ar eal Filter mca p i J te 7 o lt y Changing amp Cleaning the Post Motor Filter The post motor filter is a washable filter but should be replaced every six 6 months depending on usage Never operate the vacuum without ALL the filters in place e Push the Power On Off button to the Off position and disconnect the power cord from the wall outlet e The post motor filter is located on the rear of the vacuum Remove the filter from the filter grill Rinse in lukewarm water let dry completely Do not use a washing machine to rinse the filter Do not use a hair dryer to dry it Air dry only e When filter is completely dry replace post motor filter back into the unit and replace the filter cover Please Note The HEPA Dust Cup Filter is washable It should however be replaced every six 6 months to ensure peak performance of your vacuum The Post Motor Filter Pre Motor Filter and Pre Filter are washable They should however be replaced every six 6 months to ensure peak performance of your vacuum Important Make sure that ALL filters are completely dry before re installing back in the hand vacuum Important All filters should be checke
6. stop most of the tiniest dust particles and airborne allergens from re entering the air you breathe In fact it stops 99 97 of all particles as small as 0 3 microns many times smaller than a human hair Because of this incredible filtration performance the HEPA Dust Cup Filter will quickly accumulate dirt inside the white filter folds many fine dust particles that are difficult to see but which will eventually block or reduce your suction power if not cleaned properly Clean the HEPA Filter as described in this section then reconnect unit and proceed with vacuuming
7. Model EP724 EURO PR OX ONE 1 YEAR LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of the original purchase This warranty applies only to normal domestic household use Should your appliance fail to operate properly while in use under normal household conditions within the one 1 year warranty period return the complete appliance and accessories freight prepaid to EURO PRO Operating LLC at the address given below If the appliance is found to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date and 19 95 to cover the cost of return shipping and handling must be included In US EURO PRO Operating LLC 94 Main Mill Street Door 16 Plattsburgh NY 12901 Non durable parts including without limitation rotating brushes and electrical parts which normally require replacement are specifically excluded from warranty The liability of EYVRO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover d
8. No electricity in wall outlet Cleaner Won t 3 On Off switch not turned Run on 5 Blown fuse tripped breaker Full or clogged dust cup Clogged nozzle or dust cup port Clogged hose Hole in hose Hose not inserted fully Motor protection system activated Dirty filters Cleaner Won t Pick Up Air Flow Restricted With Attachment Use Sound Changes Attachment use restricts airflow New carpet trimmings clogging air passage 4 Thermal protector tripped _ oe SY Plug in firmly push on off switch to on Check fuse or breaker Push on off switch to on Reset thermal protector Reset circuit breaker or replace fuse Clean dust cup Remove obstruction Remove obstruction Replace hose Push hose in securely Reset thermal protector Clean change filters Check attachment Remove obstruction T GETTING TO KNOW YOUR BAGLESS CYCLONIC CANISTER 12 goth T tz TINT Tue ts AO ee N AY On Off Button Cord Rewind Button Carrying Handle Dust Cup Dust Cup Cover Dust Cup Cover Release Hose Connector Inlet Hose Connector Floor to Carpet Brush Chrome Telescopic Tube Curved Wand Hose Extension Flexible Hose Air Driven Turbo Brush Crevice Tool Upholstery Brush Trap Door Release Button echnical Specifications Main Unit 120V 60Hz 10 3 Amps Voltage Power OPERATING INSTRUCTIONS PRECAUTIONAR
9. Y MEASURES Important If the suction opening of the unit the hose or the chrome telescopic tube are BLOCKED switch off the vacuum cleaner and remove the blocking substance before you start the unit again 1 Do not operate the vacuum cleaner too close to heaters or radiators 2 Before inserting the power plug into the wall outlet make sure that your hands are dry 3 Before you start vacuuming make sure to remove large or sharp objects that might damage the dust bag L 4 When pulling out the power plug from the wall outlet pull the plug not the power cord 5 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes 6 Do not use without all filters in place Note This vacuum cleaner is equipped with a plug and power cord that retract automatically If the cord or plug get damaged it must be replaced by a qualified technician Warning Hold the plug when rewinding the cord Do not allow the cord to whip when rewinding Changing amp Cleaning the Pre Motor Filter The pre motor filter is located behind the dust cup See illustration below This is a rinseable filter but should be replaced every six 6 months Never operate the vacuum without ALL the filters in place e Push the Power On Off button to the Off position and disconnect the power cord from the wall outlet Open the dust cup cover Remove the pre motor filter and rinse in lukewarm water
10. amage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice Printed in China
11. cup lightly against the side of the waste basket garbage can Cover Release Lift cover then depress button to open trap door 6 To remove the a Rinseable TapClean HEPA dust cup filter We Lift up from the dust cup a hold the filter from the tab at the top rr of it and lift See Ze Y illustration at right VS 7 After you have removed the Rinseable TapClean HEPA dust cup filter from the dust cup separate the debris screen from the HEPA filter cartridge by holding the top rim of the filter and twisting the debris screen counterclockwise to unlock the debris screen from the filter Then lift the debris screen to remove UNLOCK w LOCK 8 Rinse the debris screen under the faucet until clean Allow to air dry or dry with a clean dish towel Do NOT wash in dishwasher 9 To replace the debris screen onto the filter slip the debris screen over the filter and twist clockwise to lock in place Warning After each Use Always remove the Rinseable TapClean HEPA Filter from the Dust Cup then vigorously TapClean HEPA Filter until no more dust can be removed Important When TapCleaning the HEPA filter hold the HEPA filter from the top rim and tap ONLY the bottom rim against the side of the waste container NEVER tap directly on the pleated folds of the HEPA filter l ___Tap Rim Y 42 aii Rim IMPORTANT Please Note The Rinseable TapClean HEPA Dust Cup Filter will
12. d regularly for signs of damage preferably after each cleaning task The filters must be replaced immediately if they become damaged Always disconnect the vacuum from the electrical outlet when checking the filters Cleaning Air Driven Turbo Brush 1 On the base of the turbo brush there is an access door for the turbine To open for cleaning push latch toward door and lift door off 2 Inspect turbine wheel and air passage for debris and or blockage Remove debris if present 3 Inspect the rotating brush for built up hair or string If present remove by carefully cutting with scissors Avoid damaging or cutting bristles 4 Once clean snap the turbine access door back in place The turbo brush will not function without the access door in place OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 9 Vigorously TapClean the HEPA Dust Cup Filter on a hard surface until no more dust is observed falling out from between the pleats of the filter See illustration at right PLEASE NOTE The white pleated filter material in the HEPA Dust Cup Filter will discolor over time This is NORMAL and will NOT affect the performance of the filter If the HEPA Dust Cup Filter IS properly f AE Wash TapCleaned J once a after each use m month or and suction a ae does not return appears to 100 then reduced we suggest that the HEPA filter be TapCleaned vigorously until no more dust can be removed the
13. e air flow Store your appliance indoors in a cool dry area Keep your work area well lit Do not immerse the hand vacuum into water or other liquids Keep end of hose wands and other openings away from your face and body SAVE THESE INSTRUCTIONS For Household Use Only WARNING To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not modify the plug in any way Rev 12 021 Shark ursuit Bagless Cyclonic Canister FOR REPLACEMENT FILTERS for Model EP724 Style XSH 24 HEPA Filter Only Style XSM724 Filter Kit Call 1 866 98SHARK 1 866 987 4275 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time or visit our website www sharkvac com FOR TECHNICAL SUPPORT for Model EP724 In U S 1 800 798 7398 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time Please Note The HEPA Dust Cup Filter may be washed We recommend that this be done once a month or when suction appears reduced To wash your HEPA dust cup filter hold filter cartridge by frame flange flange side up and rinse under water When finished shake off excess water Do NOT wash in dishwasher It is important that when you wash the HEPA dust cup filter
14. n rinsed under the faucet and allowed to dry for 24 hours before refitting into the vacuum Fig A This should be done once a month or when suction appears to be reduced Important The suction hole must be open free of any obstructions at all times Otherwise the motor will overheat and could become damaged Warning Allow 24 hours for drying before replacing in unit 10 Reassemble the debris screen to the HEPA filter cartridge and replace into dust cup container Ensure that the filter assembly is completely seated inside the dust cup container Important Do NOT use the HEPA filter cartridge without the debris screen in place 11 Insert the Rinseable TapClean HEPA dust cup filter back into the dust cup 12 Re install dust cup into the vacuum Close cover and re attach hose IMPORTANT Please note that there is a safety switch inside the vacuum where the dust cup is inserted to prevent the unit from being run without a dust cup filter in place If the dust cup filter has not engaged this safety switch the vacuum will NOT operate Therefore ensure that the dust cup filter is inserted firmly into the vacuum when assembling Changing amp Cleaning the Pre Filter The pre filter is located on the top of the Rinseable TapClean HEPA filter See illustration below This is a rinseable filter but should be replaced every six 6 months Never operate the vacuum without ALL the filters in place
15. of the power cord with the other hand to ensure that it does not whip causing damage or injury Motor Thermostat Important This vacuum cleaner is equipped with a motor protective thermostat If for some reason your vacuum overheats the thermostat will automatically turn the unit off Should this occur unplug the vacuum from the wall outlet and turn off the switch Empty the dust cup TapClean the dust cup filter and check for blockages in hose and suction inlet Allow the unit to cool for a minimum of 45 minimum prior to restarting the unit To restart re plug the vacuum into the wall socket and turn the switch back on OPERATING INSTRUCTIONS Removing amp Cleaning the Rinseable TapClean HEPA Dust Cup Filter Warning Always unplug the unit from electrical outlet before removing the Dust Cup container 1 Push the Power On Off button to Off and disconnect the power cord from the wall outlet 2 Remove the flexible hose 3 Push the dust At cup cover release AG button located ra on the front Release Button side of the unit see illustration and lift the cover up 4 Hold the dust cup by the handle and lift it up out of the vacuum 5 Hold dust cup over a waste basket garbage can lift cover and then depress the trap door release button to open the dust cup Dispose of the dust inside See illustrations below Note If dust is tightly packed and difficult to remove tap the side of the dust
16. or brush as show in the illustration below Telescopic Floor to Carpet Nozzle Air Driven Turbo Brush The efficiency of your Air Driven Turbo Brush depends on the bristle brush rotating at high speed Strong air suction is needed to accomplish this In order to ensure that maximum air suction is maintained please read the following instructions Empty the Dust Cup frequently during use Always TapClean the HEPA dust cup filter each time the dust cup is emptied Ensure that the rotating bristle brush is kept free of hair and string Inspect the turbine regularly to ensure that the air passage is free of dirt and debris See cleaning instructions on page 8 Air Driven Turbo Brush OPERATING INSTRUCTIONS Crevice Tool and Dusting Brush 1 Crevice Tool with Brush For radiators crevices corners baseboards and Wy between cushions 2 Upholstery Brush The dusting brush is used for the furniture Using your Vacuum Note Once all attachments are in place unwind a sufficient length of cable and insert the plug into the wall outlet A yellow mark on the power cord shows the ideal cable length Don t pull the power cord beyond the red mark 1 Insert the power plug into the wall outlet 2 Press the Power On Off button located on the unit to turn the vacuum cleaner On f Power Cini CH Button 3 To rewind the power cord press the cord rewind button with one hand and hold the plug
Download Pdf Manuals
Related Search