Epson 3600e Quick Setup Guide
Contents
1. information WirelessHD PowerLite Home Cinema 3600e Follow these steps to set up the included WirelessHD Transmitter 1 Place the transmitter within 32 feet 10 m of the projector Make sure the front of the transmitter faces the front of the projector See the online User s Guide for more information on the WirelessHD transmission range Note Do not place the transmitter on a metal surface as this may interfere with the signal Make sure there are no obstructions between the transmitter and the projector 2 Plug the AC adapter into the transmitter and a wall outlet 412773200 3 Connect the HDMI cables to your video input devices and the HDMI ports on the side and back of the WirelessHD Transmitter You can connect up to five input devices to the transmitter See Viewing WirelessHD content for information on switching between input sources Note You can connect tablets smartphones and other devices that support the MHL standard to the HDMI port on the side of the WirelessHD Transmitter Some devices may require an adapter or may not require an MHL cable Not all features or functions may be supported Check your device s documentation for more information 4 To use the transmitter as a pass through device to a television or other display connect an HDMI cable to the display device and the HDMI output port on the rear of the transmitter See Viewing WirelessHD content for information on switching between wire2. 3 B NMB 3 B This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator amp your body EPSON EA EXCEED YOUR VISION EPSON and PowerLite are registered trademarks and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation PrivateLine is a registered trademark of Epson America Inc Mac is a trademark of Apple Inc registered in the U S and other countries General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners Epson disclaims any and all rights in those marks This information is subject to change without notice 2014 Epson America Inc 7 14 Printed in XXXXXX CPD 41443
3. PowerLite Home Cinema 3000 3500 3510 3600e Quick Setup Before using the projector make sure you read the safety instructions in the online User s Guide Note These illustrations show the PowerLite Home Cinema 3600e but the instructions are the same for the PowerLite Home Cinema 3000 3500 3510 unless otherwise noted Connect the projector Choose from the following connections For additional connection types see the online User s Guide Note To access the rear ports on the PowerLite Home Cinema 3600e remove the cable cover by using coins or your fingernails to lift up and out on the gaps at the bottom of the cable cover Video device Connect up to 4 video devices and use the Source buttons on the remote control or the gt _ button on the projector to switch between them S 1m 5 HDMI cable ROMINA gt o RCA video cable B o Component video cable Mobile media device PowerLite Home Cinema 3500 3510 3600e Connect tablets smartphones and other devices that support the MHL standard to the HDMI 1 MHL port using a MHL compatible cable OF component oO o i C ae gm S a eae ap ig ai Ia MHL cable s fe Auso Note Some devices may require an adapter or may not require an MHL cable Not all features or functions may be supported Check your device s documentation for more
4. box If 3D images aren t displaying properly check the following Press the 3D Format button to switch to 3D viewing mode if necessary Make sure to wear the 3D glasses within 32 feet 10 m of the projector Check that your 3D glasses have not entered standby mode Slide the power switch on the 3D glasses into the Off position then back to the On position Press the Menu button on your remote control select the Signal menu then 3D Setup then select 3D Format Make sure that the Auto option is selected You may also need to set the 3D Depth and Diagonal Screen Size setting in the Signal menu See the online User s Guide for more information Check that your video device and media are both 3D compatible Refer to the documentation that came with your video device for more information If WirelessHD content isn t displaying properly check the following Check that the Link light on the transmitter is lit If the light is flashing slowly the transmitter could not connect with the projector and has entered standby mode Verify that the projector is turned on and that all cables are properly connected as shown in the Connect the projector section You may also need to press the Input button several times before the Link light turns on Make sure the WirelessHD Transmitter is within 32 feet 10 m of the projector is facing the front of the projector isn t obstructed by any large objects and is not placed
5. e the CD included with your projector or register online at epson com webreg Optional accessories For a list of optional accessories see the online User s Guide You can purchase RF 3D glasses part number V12H548006 or other accessories from an Epson authorized reseller To find the nearest reseller call 800 GO EPSON 800 463 7766 Or you can purchase online at epsonstore com U S sales or epson ca Canadian sales Notices Bluetooth Safety and Specifications Contains Bluetooth module model DBUB E207 This document provides safety instructions and describes the specifications Read this document carefully before use to ensure your safety and product performance U S FCC Notices Contains FCC ID BEMAE E207 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Howe
6. kers External speakers Video cable Video source Projector Note See your home theater receiver documentation for more information on connections Turn on your equipment 1 Turn on your video source 2 Plugin the projector 4 Press the 0 power button on the projector or the On button on the remote control The power light flashes blue then stays on Note To shut down the projector press the O power button on the projector or the Standby button on the remote control twice You don t have to wait for the projector to cool down 5 The default language of the menu system is English To select another language press the Menu button on the projector or remote control Select Settings and press Enter Select Language and press Enter Select your language and press Enter Press the Menu button to exit the menu system Adjust the image 1 If you don t see an image press one of the Source buttons on the remote control or the gt _ button on the projector to select the image source Note f you still see a blank screen or have other display problems see Troubleshooting 4 5 For the best image quality place the projector directly in front of the center of the screen facing the screen squarely If this is not possible turn the horizontal and vertical lens shift dials to adjust the image position and center it on the screen If your image is uneven o
7. less and wired display modes Connect audio Built in speaker PowerLite Home Cinema 3500 3510 3600e The projector has a built in speaker that can play audio from a connected video source DVD player streaming device etc using an HDMI connection If you do not use an HDMI connection you can connect your device s audio output to the projector s audio input ii aS ei af ii gt HDMI cable Audio cable Audio Out port PowerLite Home Cinema 3500 3510 3600e You can connect the projector to external self powered speakers through the Audio Out port 3 5 mm stereo mini cable RS 232C Note You can also connect external self powered speakers to the Optical Out port on the WirelessHD Transmitter PowerLite Home Cinema 3600e External speakers Connect your device s audio output to your home theater receiver or powered speakers Note When outputting sound through an external source you may need to reduce the projector volume to zero or make sure that the correct audio output is selected on your device to prevent duplicate sound from being heard from the projector PowerLite Home Cinema 3500 3510 3600e Home theater system Video source lt lt i e 000000000 eo fe Surround sound Video cable Receiver Powered spea
8. ly display 3D content you may need to pair them with the projector Move the glasses within 10 feet 3 m of the projector then press and hold the Pairing button on the 3D glasses for at least 3 seconds The status light on the glasses will alternately flash green and red then remain green for 10 seconds if pairing is successful You can also automatically convert 2D HDMI content to 3D PowerLite Home Cinema 3500 3510 3600e To enable the 2D to 3D Conversion option press the Menu button on the projector or remote control Select Signal and press Enter then select 3D Setup and press Enter Select 2D to 3D Conversion and press Enter Select the Weak Medium or Strong setting then press Enter See the online User s Guide for more information on adjusting 3D images Viewing WirelessHD content PowerLite Home Cinema 3600e 1 Turn on your video device and begin playback 2 Turn on the power switch on the side of the WirelessHD Transmitter 3 Turn on the projector If you have connected a television or other display to the output port on the transmitter and want to switch between wired and wireless display modes press the Output button on the remote control or transmitter The WiHD light on the transmitter will light up when the wireless display mode is active D Press the WirelessHD button on the remote control Note f the WirelessHD connection fails press the Setup button on the bottom of the transmitter then try agai
9. n 6 If you have connected multiple input devices to the transmitter press the Input button on the remote control or transmitter once to display the sub screen menu then press the button again to switch between the input devices 7 To display two WirelessHD input devices simultaneously press the P in P button on the remote control to enable picture in picture mode Press and hold the P in P button for three seconds to switch the main image and sub screen or press the P in P button again to disable picture in picture mode See the online User s Guide for more information on adjusting and configuring the WirelessHD connection and display modes Troubleshooting If you see a blank screen or the No signal message after turning on your video device or computer check the following Make sure the power light on the projector is blue and not flashing Press the gt _ button on the projector or one of the Source buttons on the remote control to switch to the correct image source if necessary If you re using a Windows laptop press the function key on your keyboard that lets you display on an external monitor It may be labeled CRT LCD or have an icon such as amp C_ You may have to hold down the Fn key while pressing it such as Fn F7 Wait a moment for the display to appear If you re using a Mac laptop open System Preferences and select Displays Click the Arrangement tab and select the Mirror Displays check
10. n the sides you can use the keystone correction feature to adjust the image To use this feature you must first set the lens to the center top position using the lens shift dials Press the 7X or _ buttons to display the keystone correction screen Then press the ZV XA 1 or Q buttons to correct for horizontal and vertical keystone distortion e o o o o J Using the remote control Make sure the batteries are installed as shown two AA batteries On Standby Turn projector on Turn projector off Choose which source to display Switch between 2D A ee and 3D Navigate projector menus Access projector menus Control WirelessHD functions PowerLite Home Cinema 3600e only EPSON For more information on using the remote control see the online User s Guide Viewing 3D images To view 3D content you must first connect a 3D compatible video device to one of the HDMI ports on your projector You will also need a pair of Epson part number V12H548006 or Epson compatible RF 3D active shutter glasses included with PowerLite Home Cinema 3500 3510 3600e 1 Turn on and begin playback on the 3D compatible video device Note Make sure you set the video device to play content in 3D mode 2 Press the 3D Format button on the remote control if necessary 3 Slide the power switch on your 3D glasses to the On position Note f the glasses don t automatical
11. on a metal surface If you are viewing wireless content make sure that the WiHD light on the transmitter is lit If it isn t press the Output button on the remote control or transmitter If the keystone correction feature doesn t correct the image make sure you first set the lens to the center top position using the horizontal and vertical lens shift dials Where to get help Manuals For more information about using the projector click the icons on your desktop to access the online manuals requires an Internet connection If you don t have icons to the manuals you can install them from the projector CD or go to the Epson website as described below Telephone support services To use the Epson PrivateLine Support service call 800 637 7661 This service is available for the duration of your warranty period You may also speak with a support specialist by calling 562 276 4394 U S or 905 709 3839 Canada Support hours are 6 am to 8 pw Pacific Time Monday through Friday and 7 am to 4 pm Pacific Time Saturday Days and hours of support are subject to change without notice Toll or long distance charges may apply Internet support Visit epson com support U S or epson ca support Canada for solutions to common problems You can download utilities and documentation get FAQs and troubleshooting advice or e mail Epson Registration Register today to get product updates and exclusive offers You can us
12. ver there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Properly shielded cables must be used for connections to LCD Projector in order to meet FCC emission limits The cable for peripheral with a ferrite core must be used for RF interference suppression Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Canada Industry Canada IC Notices Contains IC 1052D E207 This Class B digital apparatus complies with Canadian ICES 003 CAN ICES
Download Pdf Manuals
Related Search