Epson F7070 Setup Guide
Contents
1. 20 Installing the Take up Reel System 2 Lower the take up reel onto the brackets Note Leave the screws loose until the service engineer finishes adjusting the media system Installing the Take up Reel System 21 5 Connect the communication cable that is attached to the take up reel system by running it through the horizontal struts to the back of the printer Place the communication cable in the cable supports and plug it in making sure to tighten the screws on the plug to secure the cable in place 22 Setting the Language 7 Thread the power cord through the cable supports Connect the power cord to the printer and use the cable supports to restrain the cord 8 Contact a service engineer to attach the Epson Genuine Ink Supply System Ink Supply System Cover 1 and adjust the printer Do not turn on the printer until the service engineer s work is complete 9 Plug the printer into a properly grounded outlet Caution Use only the type of power source indicated on the printer s label Setting the Language 1 Turn on the printer if necessary 2 Press the Menu button 3 Press W or A to select Preferences and press OK 4 Press V or A to select Language and press OK 5 Select your language and press OK 6 Press the 5 button until you return to the main menu Adjusting the Media System 23 Adjusting the Media System After completing printer assembly and before loading me2. General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners Epson disclaims any and all rights in those marks This information is subject to change without notice 2013 Epson America Inc 3 13 CPD 38749
3. EPSON EXCEED YOUR VISION Epson SureColor F7070 Setup Guide Contents Unpacking the Pinter s 3y inka N k N veee keten 10i a ken k h nA GA W Ae aaa ele 3 Assembliino he Stand 435 404454 5514413 e TSR RT oe UR Ene a win RT deden Per ere S e mae kd 6 Ipstalline the Printer oo cece te xcs acta ica cacehavasieadsuseshcatsgaceabe anstsledssioslvecadanse EaR EE aE SEESE EEEE E TANEN E E EE AE 10 Installing the Media Feeding Unit yi 44045 444k414451455 lar ennei inar H R ba kesk Ra NA 15 Installing the Take up Reel System rexek k eke keke ke kek ke keke karke KEKE KAKA KAKA KAKA KAK K AY 19 Setting the Language i y3i ali siya seyl kaka k S yek A E KES ar ENSA Pal a pk eyn H n QER NEW k ye wak KESEN 22 Adjusting the Medid Syster scoreann aeset deken c n kilk ne K na qek aka se Kinn a aana d a clka ve kara dak Va usne x iE 23 Per e VP NE E EES ll rrr battle dade licassapsledaasndeaicabuandaummedacpeesded 25 Installing the SoftWare i l 444 0k Siney Bak ka yaka Ne eM E Z z r aka errant K na HEKE WEDE debene 31 USB Tis raat OU sss n yey ek dahn bekere eE EE ERE de lA Kn kan ke Kar kok Yen KURR KOY A ye Ki Hek Ne Ga rega a dala 32 Network Installatioti si uu nie iye dara b din Wl N NE H WERE O k k d k W k a K M W R ke H SR M W ae 33 Unpacking the Printer 3 Read all of these instructions before
4. dia mark the loading position on the left end of the media using the procedure below This ensures that the media will be fed straight and helps reduce printing errors The operation requires two people to perform any necessary adjustments in tandem from the front and the back of the printer Make sure the printer is level and on a level surface This procedure needs to be performed once during product installation 1 Open the front cover and raise the media loading lever 2 24 Adjusting the Media System 3 Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide Align the right side of the adjustment paper with the longest scale marks on both labels After aligning the adjustment paper lower the media loading lever FO 4 At the back of the printer pull the adjustment paper straight down and place it over the label on the front bar of the media feeding unit Use a pen to mark the left side of the adjustment paper on the label 25 Loading Media Raise the media loading lever and remove the adjustment paper 5 Loading Media w vo cy S T a vo P H s e g H 3 H 1 26 Loading Media 2 Open the front cover and then raise the media loading lever Loading Media 27 5 Using two or more people move the media onto the roll holder adjusting the roll hold
5. er as necessary When the media is securely on the roll holder tighten the screw 28 Loading Media 7 Pull up the roll holder lever slide the roll holder into the media roll and tighten the roll holder screw 8 Turn the roll holder handle clockwise until part A is hidden When part A is hidden do not turn the handle any further 29 Loading Media Pull the media into the printer If the left end of the media is not at the center of the rectangular area as shown in the figure on the right 9 return to step 4 10 Lower the media loading lever 11 Pull the media through the front of the printer and then raise the media loading lever 30 Loading Media 12 Pull the media out until the right end is parallel with the scale marks on the two labels Then lower the media loading lever 13 Attach the media holding plates while aligning their positions The media holding plates should be installed so that the sides of the media are visible through the three holes and the white line on the media holding plates are visible through the windows Installing the Software 31 14 Close the front cover 15 After loading the media you will be prompted to choose setup and media options Choose options as necessary Installing the Software Insert the software CD that came with your printer into your computer and follow
6. inter 1 Lock the casters and fix the stand in place To fix the stand rotate the feet clockwise until they re firmly placed on the ground Installing the Printer 11 2 Insert the carry bars into both sides of the printer with the locking bolts toward the ground Once the carry bars are inserted rotate them counterclockwise 180 to lock them into place This keeps the printer from sliding when lifted Caution Before installing the printer make sure the stand is fixed in place 3 Lift the printer as shown Caution The printer is heavy Use at least four people when lifting the printer 12 Installing the Printer 4 Lift the printer onto the stand Line up the marks on the bottom of the printer with the arrows on the top of the stand s legs before setting the printer down 5 Rotate the carry bars clockwise 180 so the locking bolts face the ground Remove the carry bars from the printer Installing the Printer 13 7 Open the front cover and remove the tape 8 Remove the media holding plates 9 Feed the long waste ink tube through the hole in the stand and secure it in place 14 Installing the Printer 10 Feed the short waste ink tube through the bracket as shown Then feed the end of the long waste ink tube into the top of the short waste ink tube Note Keep the cap and inner seal for the waste ink ta
7. nk The tank must be sealed properly for disposal 12 Install the waste ink tank into the bracket Make sure the waste ink tube is inserted in the opening Installing the Media Feeding Unit 15 13 Place the caution label for your language over the English label if necessary Installing the Media Feeding Unit You need the following parts to assemble and attach the media feeding unit 1 16 Installing the Media Feeding Unit Caution The media feeding unit is heavy and requires two people to install To avoid damaging the media feeding unit lift it by holding the two bars on the bottom as shown Installing the Media Feeding Unit 17 4 Attach the media feeding unit to the stand using four C screws Note Leave the screws loose until the service engineer finishes adjusting the media system 5 Run the communication cable through the cable supports 6 Lift the port cover 18 Installing the Media Feeding Unit 7 Plug in the communication cable and thread it through the cable supports 8 Installing the Take up Reel System 19 Installing the Take up Reel System You need the following parts to assemble and attach the take up reel system 1 Caution Use at least two people to lift the take up reel To avoid damaging the take up reel lift it by holding the two bars on the bottom as shown
8. ter 5 Media System Assembly A x2 Reel brackets Adjustment paper Roll core C_ The items below can be found in the Ink Supply System Cover 1 box X6 Bracket and mounting hardware 6 Assembling the Stand Assembling the Stand Make sure you have the following items before assembling the stand 1 Slide the large horizontal strut into both of the legs 2 Assembling the Stand 7 3 Attach the smaller horizontal strut by securing two B screws four total in the back of the right and left legs ve Em x A 4 Attach the waste ink tank bracket and secure it with a B screw 5 Attach one B screw to the other side of the bracket move the slider into place then attach another B screw 8 Assembling the Stand 6 Temporarily fasten the waste ink tube bracket using one B screw 7 8 Assembling the Stand 9 9 Slide the mounting pieces into the grooves as shown 11 Tighten the screws 10 Installing the Printer 12 Replace the plastic piece and then fasten it using the screws from step 7 Installing the Printer You need six people to install the printer four people to carry it and two people to position it on the stand Use the carry bars to lift and move the printer Make sure you have the following items before installing the pr
9. the on screen instructions You can use USB or Ethernet network connections For USB connection make sure your system has the appropriate port and that you have a standard shielded cable 10 feet 3 m or less Note Do not connect the printer until a software installation screen prompts you to To connect to a network hub or directly to your computer s network interface you need a standard RJ 45 CAT 5 or higher network cable USB Installation 32 USB Installation Power off your printer then connect the USB cable to the printer and your computer 1 Insert the CD into your computer 2 screen instructions to complete the installation 3 Follow the on 33 Network Installation Network Installation Make sure your printer is powered on 1 Connect the Ethernet cable to the printer and your networking device 2 WIT Hy Insert the CD into your computer 3 34 Network Installation 4 Follow the on screen instructions to complete the installation keeping the following points in mind Do not remove the checkmark from EpsonNet Configuration Utility and EPSON drivers and utilities in the software list e Ifyou see a firewall or network message make sure the publisher is SEIKO EPSON and then allow the connection EPSON and SureColor are registered trademarks and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation
10. using your printer Also be sure to follow all warnings and instructions marked on the printer and in the User s Guide Unpacking the Printer Before beginning assembly make sure you have sufficient space to set up and use the printer The following illustration shows the minimum space required for using the printer Callout Distance 1 19 7 in 500 mm 2 3 9 in 100 mm 3 68 9 in 1750 mm 4 39 4 in 1000 mm 114 3 in 2903 mm 6 19 7 in 500 mm 7 39 4 in 1000 mm 8 142 5 in 3620 mm 4 Unpacking the Printer When choosing a place for the printer leave adequate room for easy access and ventilation Avoid locations subject to direct sunlight excessive heat humidity or dust Be sure the printer is placed on a flat stable location that can support 496 lb 225 kg Caution Six people are required to unpack and install the printer You need an even larger floor space to assemble the printer and stand so be sure to prepare a large clear area before unpacking them Also make sure you save the box and packaging in case you need to ship the printer later The following items should be included with your printer Printer and Stand Assembly Printer re SS Caution label Horizontal struts Cable support Waste ink tube n J Waste ink Waste tank bracket ink tank Power cord Software and documentation Unpacking the Prin
Download Pdf Manuals
Related Search