Enlight EN-7100 User's Manual
Contents
1. Series EN 7100 mportant First please check your model number before proceeding The user manual is set up to correspond to the model number and installation will vary depending on the model Required tools Phillips head screwdriver pliers Photos shown may vary according to model number Step 1 Remove front bezel Place case on edge of table Fig 1 With one hand holding top of chassis pull quickly from the bottom of the bezel to remove it Fig 2 Note It might require some force to remove due to the snug fit to the chassis Fig 1 Step 2 Remove top cover Remove screws Place hands on sides of top cover and thumbs firmly on chassis Slide top cover towards you 1 Fig 3 Spread sides and lift straight up to remove Fig 3 Fig 4 Step 3 Install fan and speaker Remove fan housing by using thumbs to unfasten cl ps and place fan in housing Fig 4 Snap fan housing back into the chassis Connect fan and speaker wiring to M B as instructed in M B user manual After M B 15 installed Step 4 Install FDD HDD CD ROM 5 25 FDD DVD Fig 5 Fig 6 Fig 7 Install 3 5 HDD and FDD floppy A Squeeze tabs on side and remove 3 5 drive cassette Fig 5 Slide HDD into cassette and fasten with coarse thread flat head screws Make sure EMI clip is In place B Slide floppy into the same cassette and fasten with fine thread flat head sc2. ackof chassis to close the top cover Use hex head screws to fasten top cover to chassis Step 8 Reinstall front bezel Snap in to place starting with top snaps Make sure to line up tabs on top end with the slots in the chassis 7 2 j Se pan 20 0 000 0 q de og 0000 Part List EN 7100 SERIES 36132791 ART 3214555 ADAPTER BRACKET 3214145 IM B MOUNTING PLATE 3214544 COVER 3132621 M B LATCH 5405126 IFAN AND FAN HOLDER 5 2408334 LED HOLDER 3214566 1 SCREWED CARD GUIDE A B S WITCH HOLDER 3214602 M BSTAKE 2 HOOKED 321457 ADAPTER PLATE 3214624 EMI CLIP 3132274 RUBBER FOOT 32 140542 PLATE SPEAKER EN 7100 SERIES ACCESSORY PARST LIST P N PART NAME SLIDE GUIDE 3214566 M B STAKE 1 SCREWED 321402 STAKE 2 HOOKED SCREW PAN HEAD 6 32 5 SCREW HEX HEAD 6 32 SCREW PAN HEAD M3 5 360205 POLYBAG 8 12 INNER BOX
3. rews Then slide cassette back in to drive bay And snap in to place Install CD ROM DVD or 5 25 FDD A Fasten slide guides to the sides of CD ROM DVD or 5 25 FDD using fine thread flat head screws Fig 6 B Slide CD ROM in to 5 25 bay and snap in to place Fig 7 Step 5 Install motherboard M B A Identify if M B is AT or ATX B Remove M B mounting plate by pulling Latch towards back of chass s and swinging out the plate Fig 8 C Make sure punch out holes for 1 ports on the plate are punched out matching ports on the M B D Install at an angle first by lining up the I O ports on the M B with I O plate Fig 9 E Once holes are lined up set M B on standoffs and stakes make sure the M B 15 seated properly and fasten M B using hex head screws Note make sure stake at A3 hole 15 oriented correctly M B mounting screw holes will vary with manufacturer Please refer to M B user manual for more details Connect wires as directed in M B user manual G Reinstall M B mounting plate and swing into Place Step 6 Install the power supply P S Slide in to P S area and fasten with hex head screws Fig 10 Fig 8 Fig 10 Step 7 Reinstall top cover A Orient top cover and spread sides Slide vertically down and make sure slide fasteners guides are properly set in the rails B Once top cover is set properly on the rails slide away from you towards b
Download Pdf Manuals
Related Search