Dynex 2-in-1 Quick Setup Guide
Contents
1. height you want Center column locking screw Close the flip lever leg locks on each leg Caution Incorrectly securing a leg lock can cause the tripod leg to retract unexpectedly and could result in damage to the tripod or to the attached camera or camcorder Adjust the height of the center column by loosening the center column locking screw raising the center column to the height you want then tightening the locking screw To set the angle position of the legs press the leg release buttons and lift the tripod leg To remove the mounting plate turn the quick release plate locking knob counter clockwise to loosen it then turn the quick release plate locking knob open then lift the mounting plate to remove it Mounting plate Quick release plate locking knob Align the bottom of your camera or camcorder with the 1 4 mounting screw then secure your camera or camcorder to the plate with the screw The screw should be tight To attach the mounting plate to your tripod loosen the quick release plate locking knob then slide the plate onto the tripod head Tighten the quick release plate locking knob2. then tighten the locking screw 3 Collapse the legs 4 Press the leg release buttons and push the legs in 5 Store the tripod in the carrying case Important safety instructions Make sure that all leg locks are correctly tightened and that the legs are fully opened before use Do not carry or transport your tripod with camera equipment attached for example over your shoulder or cradled in your arms Do not expose your tripod to excessive heat or cold or use near any flame or fire Do not oil or grease any part of the tripod Do not use any solvents or thinners to clean your tripod Use only a mild detergent and wipe dry with a soft lint free cloth Do not exceed the load limit of this tripod Specifications Maximum operating height 66 5 in 168 9 cm Minimum operating height 22 64 in 57 5 cm e Folded height 24 8 in 63 cm Net weight 4 3 Ibs 2 kg e Max operating load 11 Ibs 5 kg Number of leg sections 4 e Quick release thread 1 4 in 0 6 cm Material aluminum alloy One year limited warranty Visit www dynexproducts com for details Contact Dynex For customer service call 800 305 2204 U S and Canada or 01 800 926 3020 Mexico www dynexproducts com DYNEX is a registered trademark of BBY Solutions Inc Registered in some countries Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A 2014 BBY Solutions Inc All Rights Reserve
3. Using your tripod 1 To adjust your camera to portrait position loosen the vertical tilt lock knob rotate the plate up to 90 then tighten the knob Vertical tilt lock knob 2 To adjust horizontal tilt turn the pan locking knob counter clockwise tilt the tripod head as desired then tighten the handle 3 To pan turn the pan locking knob counter clockwise pan the tripod head then tighten the knob to lock in place Note For maximum stability always make sure that your camera lens is over a leg 4 To adjust the vertical tilt loosen the vertical tilt handle then use the handle to adjust the vertical position Tighten the vertical tilt handle Converting to a monopod 1 Loosen the center column locking screw and remove the center column monopod leg with the pan head 2 With one hand grab all the twist screw leg locks on the monopod leg and twist them counterclockwise to loosen them 3 Extend the leg sections starting with the thickest section to the height you want 4 Twist each leg lock clockwise to tighten it Caution Incorrectly securing a leg lock can cause the monopod leg to retract unexpectedly and could result in damage to the monopod or to the attached camera or camcorder Center S column locking screw Monopod leg Twist locking screw Rubber foot Storing your tripod 1 Remove your camera 2 Loosen the center column locking screw Lower the column as far as it will go
4. d V1 ENGLISH 14 0372 DYN E eee DX TRPMN665 66 5 Tripod Monopod Combo Before using your new product please read these instructions to prevent any damage QUICK SETUP GUIDE Package contents Tripod Carrying case Quick Setup Guide Features 3 way pan head with slide quick release plate Smooth fluid movement for cameras up to 11 Ibs 5 kg Center column converts to a monopod that extends 59 3 in 150 6 cm Independent legs spread with three angle adjustments Reversible tripod leg G gt gt 0 T e bubble The quick release plate is level when the bubble is in the center Vertical tilt lock Adjusts vertical tilt up to 90 degrees knob Vertical tilt lock Adjusts vertical tilt for head handle Leg release button Lets you adjust the leg angle position Mounting plate Holds your camera S e Holds your camera S e camera Quick release plate Secures the quick release plate to the tripod locking knob Pan locking knob Locks the tripod head so that it will not rotate horizontally Center column Locks the center column in place locking screw Center column Provides quick height adjustment monopod leg Flip lever leg locks Locks the legs in place Rubber feet Provide a secure non slip footing for your tripod Setting up your tripod 1 Open the flip lever leg locks on each leg 2 Extend the leg sections from the top down thickest section first to reach the
Download Pdf Manuals
Related Search