Dynasty Spas MC-MP-DY2 User's Manual
Contents
1. C above Set Point The Filter icon will blink on 0 5 second off 0 5 second on 0 5 second off 1 5 seconds Troubleshooting y Pumps have started up for one minute on several occasions and Filter Cycle icon is flashing displayed Not a bug but a feature 44 C Our Smart Winter Mode protects your system from the cold by automatically turning the pumps on for one minute several times a day to prevent water from freezing in pipes The display is flashing A power failure has occurred Press any key to reset the system then reprogram all desired parameters Quick Reference Card Water temperature is Water temperature in the spa has reached 12 F Do not enter the water Allow water to cool down The system will reset au tomatically when water reaches 109 F 43 C Call your dealer or service supplier if problem persists 3 flashing dots are dis played A problem has been de tected Do not enter the water Check and open water valves Clean filters if nec essary Check water level Add water if needed Shut power off and power your spa up again to reset the system Call your dealer or service supplier if problem persists Step Programming Sequence YC Time of day NYC Filter cycle start time Yee Filter cycle duration mm Filter cycle frequency MYCE Economy mode start time AY eM Economy mode duration on NCW ame Storing settings in memory amp2. returning to Normal mode Step I Time of day Setting the time Enter Programming mode by holding Prog key pressed down for 2 seconds 10 25 m 2 The display will show the current setting NV 11 43 om 3 Use Up and Down arrows to change setting Steps 2 amp 3 Filter cycle start time amp duration The system automatically performs two filter cycles per day at 2 hour intervals During the filter cycle Pumps amp 2 and the blower will run the first minute then Pump 3 will run for one minute Pump will then run at low speed for a programmed number of hours The Filter Cycle icon lights up when a filter cycle is on To program a filter cycle you must enter the time you want the cycle to start and 2 the duration of the cycle If no filtering is required the duration should be set to 0 For continuous filtering the filter cycle duration should be set to 12 00 Setting filter cycle start time Press Prog key a second time fso 2 The display will show FSxx with xx representing the starting hour Aw Fsiz_ 3 Use Up and Down arrows to change setting Setting filter cycle duration Press Prog key a third time Fdoo 2 The display will show Fdxx with xx representing the duration in hours Aw Fai 3 Use Up and Down arrows to change setting Step 4 Filter cycle frequency Setting filter cycle frequency Press Prog key a fourth time Fro 2 The display will show FFx
3. Lock icon will be displayed Locking your digital control pad amp Press and hold Pump I key for 5 seconds LocP 2 The display will show LoeP with P representing Partial lock LocF 3 Release the key and the keypad will be in Partial lock mode Keep key pressed down for 5 more seconds if you want to be in Full lock mode The LocF message will then be displayed When control pad is locked all automatic functions of the system run as usual If a key is pressed down a LocP or LocF message will be displayed for second To unlock the keypad simply press and hold Pump I key again for 5 seconds Economy mode Press Econo key to switch from Normal mode to Economy mode To save energy the Economy mode Set Point is 20 F 1 C below the Normal mode Set Point gt The Economy Mode icon lights up when Economy mode is on There are 3 available Economy operating modes noEc No Economy mode Ec l Economy mode always on Ec 2 Economy mode on during a programmed number of hours see Steps 5 amp 6 Selecting the desired Economy mode N Press and hold Econo key for more than 2 seconds noe 2 The display will show the current mode noEc Ec or Ec 2 Ec 3 Keep key pressed down until the desired mode is displayed After 5 seconds the new setting will be programmed Inverted display Press and hold Pump 2 for 5 seconds to invert the display Note that the F or C icon is not displayed in rev
4. 2 is on at low speed Starting Pump 3 Press Pump 3 to turn Pump 3 on Pressing a second time turns Pump 3 off A built in timer automatically turns pump off after 20 minutes unless manually desactivated first Starting the blower Press Blower to turn blower on at high speed Press a second time to turn blower to low speed A third time turns blower off A built in timer turns blower off after 20 minutes unless manually deactivated first i i The Blower icon lights up when blower is on at high speed It flashes when blower is on at low speed Temperature display unit Press and hold Light key for 5 seconds to display water temperature in either Fahr enheit F or Celsius C MC MP DY2 SPA PACK Automatic water heater start When water temperature is F 0 5 C lower than the Set Point the heater will automatically turn on until water tempera ture reaches Set Point plus F 0 5 C The Heater icon lights up when the heater is on It flashes when there is a request for more heat but the heater has not yet started Setting water temperature Use Up or Down arrow key to regulate water temperature The temperature setting will be displayed for 5 seconds to confirm your new selection The Set Point symbol indicates the desired temperature NOT the current water temperature Water temperature can be adjusted by in crements from 59 to 104 F 15 to 40 C Time amp temperature
5. display The display toggles every 5 seconds alternately showing the hourly time and the current water temperature Turning the light on Pressing Light key once turns light on at high intensity Pressing a second time turns light to low intensity A third time turns light off A built in timer turns light off after 2 hours unless it has been manually deactivated xy The Light icon is displayed when light is on at high intensity It flashes when light is on at low intensity Fiber Box Option If spa has an optional fiber box only pressing Light key turns fiber box motor amp light on Pressing again turns fiber box motor off but leaves light on A third time turns both motor and light off A built in timer turns fiber box off after 2 hours unless it has been manually deactivated The Light icon is displayed when fiber box light is on It flashes when fiber box motor and light are on at the same time Fiber Box amp 12V light via jumper Pressing Light key once turns fiber box motor amp light and 2V light output on Pressing again turns fiber box motor off but leaves lights on A third time turns 2V light off and a fourth time shut fiber box light The Light icon is displayed when fiber box motor is off and both lights on or only the fiber box light It flashes when fiber box motor amp light and 2V light are on u The filter cycle is suspended if the water temperature raises more than 2 F 1
6. erse mode Follow the same procedure to return to default mode If a power up occurs the display always returns to default mode Summary of control panel parameters FOIL FSxx Filter cycle start time Fdxx Filter cycle duration FFxx Filter cycle frequency ESxx Economy mode start time Edxx Economy mode duration Tu X Temperature unit LocX Control pad lockout 9919 100417 B
7. excalibur series wn aN A A Pump 2 a Ze X Light Prog N 3 A A Econo The Quick Reference Card provides a quick overview of your spa s main functions and the operations accessible with your digital control pad Starting Pump Press Pump I to turn Pump on at low speed Pressing a second time turns Pump to high speed A third time turns Pump off When at high speed a built in timer turns pump off after 20 minutes and when at low speed after 2 hours unless it has been manually deactivated E The Pump I icon lights up when A Pump lison at high speed It flashes when Pump is on at low speed Starting Pump 2 When blower or Pump 3 are not installed Press Pump 2 once to turn Pump 2 on at low speed Pressing a second time turns Pump 2 to high speed A third time turns pump off A built in timer turns pump off after 20 minutes unless manually deactivated first amp The Pump 2 icon lights up when Pump 2 Is on at high speed It flashes when Pump 2 is on at low speed When blower and Pump 3 are installed Press Pump 2 once to turn Pump 2 on at low speed Pressing a second time turns Pump 3 on and Pump 2 to high speed A third time turns both pumps off A built in timer auto matically turns pumps off after 20 minutes unless manually deactivated first The Pump 2 icon lights up when Pump 2 and Pump 3 are on at high speed It flashes when Pump
8. x with xx representing the frequency per day he rro4 3 Use Up and Down arrows to change setting Steps 5 amp 6 Economy mode start time amp duration Setting Economy mode start time Press Prog key a fifth time Eso 2 The display will show ESxx with xx representing the starting hour Aw esos 3 Use Up and Down arrows to change setting Setting Economy mode duration Press Prog key a sixth time Edo 2 The display will show Edxx with xx representing the duration in hours Any Edo4 3 Use Up and Down arrows to change setting Step 7 Storing settings in memory Press Prog key a seventh time to store settings in the system s non volatile memory and to return to Normal mode SPA excalibur series Programming Mode Temperature unit Filter Cycle icon Up amp Down icon arrows Economy Mode icon Lock icon Digital control pad lockout This function allows you to prevent unauthorized parameter setting of the unit This feature is especially helpful when young children have access to the keypad There are two modes you can choose from Full lock or Partial lock Full lock means that all keypad functions are locked Partial lock means that the basic functions of the spa will remain accessi ble pumps blower and light but it will be impossible to change the temperature Set Point to override the Economy mode or to enter the Programming mode When control pad is locked the
Download Pdf Manuals
Related Search