Dixon ZTR 304 User's Manual
Contents
1. 24 DEDO 02235 0225 16 9 902 7 3 A 3 4117 5 2 519 3 3 212 8 19 9914 v0 1152 ea 96 2242 016 gt 2159 195 695 2 3 4 Page 5 70 HIZ TSCOW ATBNISSY A008 Page 6 550 1041 AS ar RL hI LOS al 9306 Nu 6086 Se 205 24 Page 7 a A n A PUE 814 UNLBIM AIEWISSV 335 9519 21 WOOT ONIBIA 008 HOLIMS E NOI LIND L I 0 ar n 85 5357 5 URNA a 9313915 038 YOLYNY3LIYT 9997 2 CIO OLINIVH AINO YIAOD 99bb ni 2193559 S9yb 195 DAA ree E ALA VO HOLIMS ale 3930 OL i 3 i i HOLAS i 1935 I 012. located at from ofmower deck on slide plates welded at battery box and remove Lift front ofmower chassis and roll free of the deck To install reverse the above procedure a tee Ne IDJUSTMENT OF MOWER DECK DRIVE BELT The mower deck drive belt is tensioned by a spring loaded engagement idler quadrant 2 This system is designed to maintain the proper belt tension at all times 3 Belt tension can be adjusted by moving the engaging rod P N 7013 into the outside hole of engagement handle P N 7020 4 After belt tension 15 adjusted check to assure that the mower blade will not turn freely when the engaging rod is in the OFF position If the mower blade urns freely adjust the blade by loosening nut P N 3205 at end of the brake linkage P N 7015 6 After adjustment is achieved perform the safety checks listed below Page 2 IMPORTANT PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS After reassembly while seated on mower attempt to start engine with mower deck engaged Engine should not start If engine does start return the mower to an Authorized Dixon Dealer for adjustment or repair 2 Disengage mower deck and start engine Withthe operator inthe normal seated pos tion engage mower deck and remove weight from seat The engine should stop If the engine does not stop when operator rises from seat return the mower to an Authorized Dixon Dealer for adjustment or repair Engage
3. then disengage mower blade in each cutting height Insure that blade disengages and comes to astop within 5 seconds ineach height position If blade does not disengage properly contact your Authorized Dixon Dealer PARKING BRAKE ADJUSTMENT 1 Raise upper body to the open position 2 Tighten nut on brake rod P N 2533 located in front of the transaxle on each side just enough to prevent brake from slipping when engaged CAUTION Over tightening may cause premature wear on the brake bank P N 279274 REMOVING THE MOWER BLADE Secure blade P N 2483 from turning Remove blade bolt from center P N 3268 lock washer P N 3065 and blade washer P N 6113 then blade P M 2483 To reinstall reverse above procedure WARNING Sharp edges on blade can cause injury Caution should be exercised when service is required on blade P N 8112 rr E 000400000 DIXON INDUSTRIES INC Box 1569 Coffeyville Kansas 67337 0945 316 251 2000 Airport Industrial Park TELEX 417109 Page 3 74 _ ABs I Ove RN MOMISST 20 a a a 1 ISLA A ot 13814 7 Y cope dI Ziy 4 Cop Page 4 302 9952 2 5115 951 044 5 RINSE 5 50 5998 ils 911 Sata diuo 4 DE
4. 2 8 Revised Page 1 TECHNICAL DATA BROCHURE MODEL ZTR 304 IMPORTANT READ OPERATOR S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS BODY REMOVAL The 304 has a 2 piece fabricated steel body The upper body be folded forward to expose the transaxle In some cases it may be necessary to remove the upper body to service the transaxle PA To remove upper body fold forward and remove bolt P N 3006 from cable P N 3780 Shut upper body and remove the two cotter pines P N 3058 from the front of upper body support Carefully lift upper body from frame 3 Reverse above procedure to reinstall SEAT ADJUSTMENT 1 Raise upper body 2 Loosen four seat bolts P N 3093 and slide seat forward or backward to desired position 3 Retighten bolts MOWER BLADE OPERATION To engage the mower blades turn lever on floor slowly to the ON position To disengage mower blades turn lever slowly to the OFF position REMOVING MOWER DECK Loosen the belt keeper P N 7026 amp 7027 located under the engine loosing two rear engine mounting bolts allowing the deck drive belt tocomefree of the rear pulley Disconnect the wiring loom at the deck safety switch P N 4242 Remove the two clevis pins P N 3072 from the two rear L rods P N 1355 and slide from slots Remove clevis pins P N 3072 L rod attached to lift handle and slide from slot Remove clevis pin P N 3072 from front deck hanger shaft P N 1332
Download Pdf Manuals
Related Search