Disney 72-4131-250 User's Manual
Contents
1. 72 4131 250 8 03 Owner s Manual ey Congratulations 1 on your purchase of the Lionel Dumbo Pylon Watch as Dumbo circles the tower Mrs Jumbo and Timothy Q Mouse peer out of the illuminated windows at the base of the pylon Dumbo Pylon Inventory e Pylon e Two green wires e Dumbo figure e Owner s Manual Support arm Service Center list e Switch Table of contents Wiring your Dumbo Pylon with a conventional power supply Installing your Dumbo Pylon Attaching the figure to your Dumbo Pylon Operating your Dumbo Pylon with a conventional power supply Operating your Dumbo Pylon with TrainMaster Command Control Replacing the lamp in your Dumbo Pylon Limited Warranty Lionel Service 3 4 7 8 9 11 12 The following Lionel marks may be used throughout this instruction manual and are protected under law All rights reserved Lionel TrainMaster Odyssey RailSounds CrewTalk TowerCom DynaChuff StationSounds Pullmor ElectroCoupler Magne Traction CAB 1 Remote Controller PowerMaster Lionel XIV XIV PowerHouse TMCC Lionelville Lockon The name FasTrack is used with permission from Pitsco Inc 2 Wiring your Dumbo Pylon with a conventional power supply Wi your accessory is the first step in preparing for flight The Dumbo Pylon will operate best at 12 18 volts AC and it can be powered through track power with a Lionel Lockon available sepa2. you must first call 586 949 4100 or FAX 586 949 5429 or write to Customer Service P O Box 748 New Baltimore MI 48047 0748 stating what the item is when it was purchased and what seems to be the problem You will be sent a return authorization letter and label to ensure your merchandise will be properly handled upon receipt Once you have received your return authorization and label make sure that the item is packed to prevent damage during shipping and handling We suggest that you use the product s original packaging This shipment must be prepaid and we recommend that it be insured Please make sure you have followed all of the above instructions carefully before returning any merchandise for service You may choose to have your product repaired by one of our Authorized Lionel Service Centers after its warranty has expired A reasonable service fee will be charged Warranty Information Please complete the information below and keep it along with your dated sales receipt You must present this and your dated sales receipt when requesting warranty service ame Address Place of Purchase Date of Purchase Product Number Product Description 2003 LIONEL L L C CHESTERFIELD MI 48051 2493 UNITED STATES OF AMERICA PRINTED IN CHINA
3. ds this warranty Modification of this product voids this warranty Any warranted product which is defective in original materials or workmanship and is delivered by the original consumer purchaser to Lionel L L C or an authorized Lionel L L C Service Center together with proof of original purchase will at the option of Lionel L L C be repaired or replaced without charge for parts or labor In the event the defective product cannot be repaired and a replacement is not available a refund of the original purchase price will be granted Any products on which warranty service is sought must be sent freight or postage prepaid as transportation and shipping charges are not covered by the warranty In no event shall Lionel L L C be liable for incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion may not apply to you This limited warranty gives you specific legal rights and you may have other rights which vary from state to state Instructions for Obtaining Service f service for this Lionel L L C product is required bring the item along with your dated sales receipt and completed warranty information to the nearest Authorized Lionel Service Center Your nearest Lionel Service Center can be found by calling 1 800 4 Lionel or by accessing our Website at www lionel com f you prefer to send your product back to Lionel L L C for repair in Michigan
4. oof and pylon tower Refer to Figure 5 on page 10 for the location of the screws 3 Locate the lamp in its small black fixture Carefully pull the lamp straight up and out of the socket Refer to the Figure 6 on page 11 for the lamp location 4 Install the replacement lamp Line up the bottom of the bulb with the socket and carefully push the lamp down into place 5 Reassemble the Pylon following these steps in reverse order Replacing the lamp on your Dumbo Pylon continued Base of the Pylon Mounting holes Base screws recessed Mounting holes Roof screws recessed Figure 5 Screw locations 10 Replacing the lamp on your Dumbo Pylon continued Interior of the building with the roof removed Figure 6 Lamp location 11 Limited Warranty Lionel Service his Lionel product including all mechanical and electrical components moving parts motors and structural components except for light bulbs is warranted to the original consumer purchaser for one year against original defects in materials or workmanship when purchased through an authorized Lionel merchant This warranty does NOT cover normal wear and tear light bulbs defects appearing in the course of commercial use or damage resulting from abuse or misuse of the product by the purchaser Transfer of this product by the original consumer purchaser to another person voi
5. rack Lockon a FasTrack Accessory Power Wire OR the Common Ground U terminal on the accessory power supply Connect it directly to one of the spring clip terminals at the bottom of the pylon At this point your accessory is wired for power The next section explains how to operate this accessory in a conventional non TrainMaster Command Control environment Wiring your Dumbo Pylon with a conventional power supply continued Mounting holes Mounting holes POWER gt SUPPLY _11111111111111111111111 FasTrack Accessory Power Wire Figure 1 Wiring for conventional operation Installing your Dumbo Pylon hoose a flat level area on your layout for the accessory Secure this accessory to your layout with four screws not included using the holes near the corners of the base Be sure to wire your accessory before you secure it to your layout the wire terminals are on the underside of the base Keep in mind that Dumbo flies in a circle with diameter of 30 The flight path must be kept clear Attaching the figure to your Dumbo Pylon Cu the assembly of your Dumbo Pylon by attaching the Dumbo figure and support rods to the structure Figure 2 illustrates the following procedure 1 Note that the supporting rod has different shaped ends Insert the flattened end of the support rods into the tube protruding from the top of the pylon Refer to the diagram for further assi
6. rately 6 62900 or a FasTrack Accessory Power Wire available separately 6 12053 OR through an accessory power supply We recommend that you choose a power supply that will allow you to increase or decrease the voltage to the accessory Changing the voltage allows you to control the speed at which the figure circles the pylon Figure 1 on page 4 illustrates the following procedure To make proper connections you need the insulation at the ends of the wires to be stripped back 1 4 to 3 8 To strip the wires use a pair of wire strippers Caution Only an adult should perform this task Always use care when stripping wires 1 Attach one wire to the 1 terminal of the track Lockon a FasTrack Accessory Power Wire OR the Power A terminal on the accessory power supply Connect it to one of the terminals on the separate switch included with this accessory 2 Attach an additional wire to the other terminal on the switch Connect the other end of this wire to one of the spring clip terminals at the bottom of the pylon Note To make the spring clip terminal connections press down on the springy top of the terminal clip so that a metal loop is formed Slide the bare end of the wire into the exposed loop Release pressure on the terminal clip allowing the crimped metal to pinch the end of the wire in the metal loop Give a little tug on the wire to check if the hold is secure 3 Attach another wire to the 2 terminal of the t
7. stance 2 Insert the D shaped ends of the wires into the openings in the bottom of the Dumbo figure Support rod bottom Mounting hole bottom of Dumbo Mounting hole on Support rod top top of pylon Figure 2 Installing the support rods Operating your Dumbo Pylon with a conventional power supply djust the voltage to the accessory to control the speed at which Dumbo circles the tower Increasing the voltage will cause Dumbo to circle faster decreasing the voltage will cause Dumbo to travel slower To turn the accessory off turn off the power supply or use the switch attached to the wires in Step 1 on page 3 Operating your Dumbo Pylon with TrainMaster Command Control ou may choose to wire your accessory with an SC 2 Switch and Accessory Controller available separately 6 22980 or the Accessory Switch Controller available separately 6 14182 Refer to these manuals for additional information SC 2 wiring and operation Three wires not included are needed to connect your Pylon to the SC 2 and a separate accessory transformer We recommend using 22 gauge wire Refer to Figure 3 1 Attach one wire to the transformer Common Ground U terminal and connect it to the accessory COMM common position on the SC 2 2 Connect one of the Pylon terminals to the accessory ON OFF toggle position on the SC 2 3 Finally connect the remaining Pylon terminal to the transformer Power A terminal Use the AUX2 button on
8. your CAB 1 Remote Controller to toggle the Pylon ON and OFF Y acci ACC1 ANONY CAA NG QAI QAI AKA ACC ACC2 POWER Common Ground U SUPPLY Power A Figure 3 Wiring for Command operation with an SC 2 Operating your Dumbo Pylon with TrainMaster Command Control continued Accessory Switch Controller wiring and operation Three wires not included are needed to connect your Pylon to the Accessory Switch Controller ASC and a separate accessory transformer Refer to Figure 4 1 Attach one wire to the transformer Power A terminal and connect it to the COMM terminal on the ASC 2 Connect one of the Pylon terminals to a numbered accessory terminal on the ASC 3 Finally connect the remaining Pylon terminal to the transformer Common Ground U terminal Use the AUX2 button on your CAB 1 Remote Controller to toggle the Pylon ON and OFF Common Ground U Power A CCC L CC Figure 4 ASC connections Replacing the lamp in your Dumbo Pylon yr Pylon is illuminated by one 18 volt lamp During the course of normal operations this lamp may require replacement Follow these steps to replace the lamp with Lionel part no 612 3011 311 1 Lift the support arm out of the tubes at the top of the pylon Also remove any screws securing the base to your layout 2 Remove the four base screws from the underside of the base with a small Phillips head screwdriver and lift away the r
Download Pdf Manuals
Related Search