Desa EL36L User's Manual
Contents
1. SAFETY ARWARNING Improperinstalla tion adjustment alteration ser vice or maintenance can cause injury or property damage Refer to this manual For assistance or additional information consult a qualified installer Al CAUTION Donotexpose the heater to the elements such as rain etc Do not place clothing or other flammable material on or near firebox Never place any objects on the fireplace Carefully supervise young chil dren when they are in the room vvith fireplace Fireplace becomes very hot when running Keep children and adults away from hot surfaces to avoid burns or clothing ignition Fireplace will remain hot for a time after shutdown Allow sur faces to cool before touching Do not install fireplace directly on carpet or similar surface which may restrictair circulation beneath unit When using electrical heaters basic precau tions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 2 www desatech com 1 Read all instructions before using this heater 2 Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9 m from front of heater 3 This heater is hot when in use To avoid burns do not let bare skin touch hot surfac es The grill directly in front of heater outlet becomes hot during heater operation 4 Extreme c2. 4 Remove screws securing each side of log with Standofis to brackets see Figure 13 Figure 13 Removing Log and Ember LED 5 Carefully remove old log 122663 01D www desatech com 9 SERVICING Continued REPLACING SCREENS 2 Open bi fold doors if equipped and 1 Open upper control panel door Turn screens power switch off 3 Remove screws securing each side of log 2 Open bi fold doors if equipped to brackets see Figure 13 page 9 3 Remove 2 screws securing screen rods 4 Carefully remove log see Figure 14 5 Remove screws from back corners and 4 Tilt rod down and remove from bracket front of top panel see Figure 15 Remove 5 Remove old screen from rod and discard top panel and set aside Install new screen onto rod Note For LED drum and motor only 6 Reinstall rod into bracket and replace remove back screws Top panel does not screws have to be completely removed Care 7 Close doors fully push top panel up to remove screen glass 6 Using gloves gently remove glass panel Mounting by sliding it toward you There is a rubber bumper on each corner of glass Set aside in a safe location 7 Follow instructions on pages 11 thru 13 to replace part 8 Using gloves install glass by gently slid ing smooth side toward fireplace front into brackets on either side that hold glass in place Y Y 9 Reinstall top panel Pull top panel down Retaining Screw Figur
3. approximately 72 F 22 C Note Fan on heater will continue to run for 5 7 seconds after heater has been turned off 3 When using remote control aim remote at sensor located in center of unit just above log set IMPORTANT This remote control must remain within 20 feet 6 m of fireplace to be effective 4 When power switch is turned off fireplace settings go back to default see Figure 10 HEATER Off Lovv Medium High FLAME Off Lovv Medium EMBER Off Low Medium BACKLIGHT Off Figure 10 Fireplace Settings Default Settings are Circled High ACCESSORY INSTALLATION OPTIONAL GLASS DOORS Model EL36L only Doors are included vvith models EL36LD and VE36LBHB Model EL36L will accept bifold glass doors that are fully operable Installing Bifold Glass Doors Follow these steps to install left and right operable panels 1 With handle down completely fold panel on its hinges 2 With handle facing center of firebox open ing insert lower pivot pin on door panel into hole in bottom outer edge of firebox opening see Figure 11 3 Keep folded door tilted and slide upper two pins into guide track below upper facial edge of firebox opening 4 Tilt glass assembly fully vertical until outer pivot pin snaps into mounting hole in up per spring clip 5 Once top and bottom pins are secured unfold door into closed position 6 Repeat steps 1 through 5 for opposite door assembly 7 To adjust doors slide parti
4. Watts 1500 3000 Amps 15 Amp 20 Amp Grounded Circuit Note This heater must be electrically wired and grounded in accordance with local codes or in the absence of local codes with National Electric Code ANSI NFPA 70 latest edition or the Cana dian Electric Code CSA C22 1 as appropriate PRODUCT DIMENSIONS p 24 110 TOP 15 1 8 I 2 gt pa tl 5 tl w Q 3 a 3 o e Hm J s E 9 h D e aaa a y 1 n LEFT SIDE 42 1 8 To Nail Location RIGHT SIDE FRONT Figure 1 Heater Dimensions 122663 01D www desatech com Control Door Heat Vents Behind Door Front Glass Carefully remove unit from box Prior to per Panel ib anel N PRODUCT IDENTIFICATION Flame Control Ember Control Backlight Control Remote Hide Heater Control 7 Catch ON OFF Povver Button Figure 2 Product Identification UNPACKING AND TESTING manently installing unit test to make sure unit A WARNING Do not operate operates properly Unit does not come witha the unit if it is damaged or has power cord installed Unit must be hard wir
5. install shoulder screws before insert ing fireplace into opening See instructions included with trim kit If installing a mantel you must follow clearance instructions see Installation Clearances page 5 Platform Subflooring Figure 6 Framing Dimensions These Dimensions Allow for 11 5 of Clearance to Side Wall of Fireplace and 10 Clearance to Perpendicular Side Walls 11 8 8 58 1 4 Figure 7 Corner Dimensions 122663 01D INSTALLATION Continued A hearth extension is suggested for a more pleasing appearance The fireplace may be raised on a wood or non combustible platform supporting its entire width and depth and extending in front of the fireplace as long as louvers are not obstructed Note When installing fireplace in cold cli mates against a non insulated exterior wall wall must be fully insulated in accordance with local building code ELECTRICAL INSTALLATION A VVARNING Any electrical re vviring of this appliance must be done by a qualified electrician This vviring must be done in ac cordance vvith local codes and or in the U S A vvith the current Na tional Electrical Code ANSI NFPA No 70 and in Canada vvith CSA C22 1 Canadian Electric code This fireplace should be con nected to a dedicated 15 amp 120 60 or 20 amp 240 60 circuit as other appliances may cause the circuit breaker to trip or fuse to blovv vvhen fireplac
6. please have your model and serial numbers of your heater ready You can also visit DESA Heating LLC s web site at www desatech com 16 www desatech com Usually we will ask you to return the part to the factory PARTS NOT UNDER WARRANTY Contact authorized dealers of this product If they can t supply original replacement part s call DESA Heating LLC at 1 866 672 6040 for referral information A list of authorized dealers can be found by visiting www desatech com When calling DESA Heating LLC have ready model and serial numbers of your heater the replacement part number 122663 01D ACCESSORIES Purchase these accessories from your local dealer If they can not supply these accessories either contact your nearest Parts Central or call DESA Heating LLC at 1 866 672 6040 for information You can also write to the address listed on the back page of this manual 36 PERIMETER TRIM KITS PT36 Black PT36B Brushed Brass PT36PB Polished Brass PT36P Platinum 36 BIFOLD GLASS DOOR KITS BD36 Black BD36B Brushed Brass BD36PB Polished Brass BD36P Platinum 122663 01D www desatech com MODEL EL36L EL36LD VE36LBHB 122663 01D www desatech com 18 PARTS MODELS EL36L EL36LD VE36LBHB This list contains replaceable parts used in your fireplace When ordering parts follow the instructions listed under Replacement Parts on page 1
7. 01D www desatech com 11 SERVICING Continued TRANSFORMER 1 Follow steps 1 through 6 under Service Preparation page 10 2 Disconnect transformer wires from control board 3 Remove 2 screws from firebox surround to remove transformer see Figure 18 4 Remove and discard transformer 5 Place new transformer against inside of firebox surround and replace screws removed in step 3 6 Reconnect transformer wires to control board see Wiring Diagram page 14 6 Follow steps 8 through 13 under Service Preparation page 10 Screws Transformer N N Nuts Figure 18 Removing Transformer HEATER 1 Follow steps 1 through 6 under Service Preparation page 10 2 Disconnect wires from heater 3 Remove 4 screws from side of heater see Figure 19 4 Install new heater 5 Connect wires to new heater see Wiring Diagram page 14 6 Follow steps 8 through 13 under Service Preparation page 10 12 www desatech com Figure 19 Removing Heater from Blower BLOWER ASSEMBLY 1 Follow steps 1 through 6 under Service Preparation page 10 2 Disconnect wires from heater blower as sembly 3 Remove 4 screws holding blower heater and brackets to fireplace top see Figure 20 4 Remove 4 screws securing heater to blower see Figure 19 5 Install old heater onto new blower with screws removed in step 4 6 Install new blower heater assembly to top panel with screws removed in step 3 7 Re
8. 6 of this manual 122663 01D KEY NO PART NO 1 120929 01 2 120929 02 3 120929 03 4 120929 04 5 120929 05 6 120928 46 7 120928 44 8 120927 16 9 120929 09 10 120929 10 11 120929 11 12 120929 12 13 120929 13 14 120929 14 15 120929 15 16 120929 16 17 120929 17 18 120929 18 19 120929 19 20 120929 20 21 120928 40 22 120927 08 23 120928 42 24 120928 43 25 120928 27 26 120928 26 27 120927 21 28 120927 12 29 120927 24 30 120929 21 31 120927 14 32 120927 20 120929 06 120929 07 120929 08 120927 23 DESCRIPTION Door Handles LED Ember Strip Log Set Rear Glass Screen Flame Effect Mirror Heater Blower Bracket Flame Effect Mirror Bracket Back Light Strip Top Glass Door Left Glass Door Right Control Panel Door Front Panel Mesh Screens Screen Rods Back Panel Left Side Back Panel Center Back Panel Right Side Magnetic Catch Bottom Panel Grate Handles Heater Blower Transformer Control Board and Standoffs Remote Control Sensor Settings Control Board ON OFF Switch LED Drum Assembly Motor Remote Control PARTS AVAILABLE NOT SHOWN n n Wire Flame Effect Wire Ember Bed Wire Backlight Thermocouple Optional for model EL36L www desatech com Bs Bs Bs Bs BS pp Be fo BS fol By BS gt BS Ex BS BS fo QTY 5 65 WARRANTY KEEP THIS WARRANTY Model located on prod
9. DESA HEARTH PRODUCTS ELECTRIC FIREPLACE INSERT SAFETY INFORMATION AND INSTALLATION MANUAL MODELS EL36L EL36LD AND VE36LBHB PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE Al WARNING If the information in this manual is not fol lowed exactly an electrical shock or fire may result caus ing property damage personal iniury or loss of life FOR YOUR SAFETY Do not store or use gasoline or other flammable va pors and liquids in the vicinity of this or any other appliance nstallation and service must be performed by a qualified service agency This fireplace meets the construction and safety stan dards of H U D for application in manufactured homes when installed according to these instructions INSTALLER Leave this manual with the appliance CONSUMER Retain this manual for future reference For more information visit www desatech com TABLE OF CONTENTS Salety r un b nun bli Listing Approvals coo sonic Azda dec Product Dimensions Product Identification Unpacking and Testing Locating Fireplace Installation Operation Accessory Installation 2 ssecccceccsceeceessgsessaecescee ONDA 5 55 0 Cleaning O 9 SOMVICING oia Abas 9 VViring Diaqram sasi d airis 14 Troubleshooting da Replacement Parts Technical Service Accessories
10. N CLEARANCES Minimum clearances to combustible construc tion are Top Back and Sides of Recessed Cabinet 0 Min Drywall to Sides of Front Face 0 Min Framing at Nailing Flanges 0 Min Ceiling to Opening 36 Min Floor 0 Min Front 36 Min Perpendicular Side Wall 10 Min Mantel Clearances For mantel clearances see Figures 4 and 5 7 Facing Material May Be Noncombustible Wall Treatments or 12 Ref Combustible Wood 1 0 10 Combustible Wood 412 Mantels and Trims 1 2 May Extend Above ane Profile Shown when Tt 1 Maintained within VA 30 Parameter Shown 1 Framed 23 Material 21 le 17 Top of Cabinet 15 Min Note All Mantel Clearances are Measured from Top of Fireplace Opening Figure 4 Mantel Clearances Edge of Firebox 3 4 Opening Top View of Fireplace Di bs Safe Zone ne ahu Combustible 30 Material Must m m Not Overlap VU Minimum 10 Front Face from Perpendicular Side Wall Figure 5 Mantel Side Clearances INSTALLATION Continued A WARNING RISK OF FIRE Wiringto powersource mustnot be pinched or against a sharp edge A WARNING RISK OF FIRE To prevent a possible fire do not block air intake or exhaust in any manner Do not use on soft surfaces where openings may become blocked WARNING RISK OF FIRE Do not blow or place insulation against the firebox WARNING If t
11. a qualified installer in accordance with all local codes and instructions furnished with this product This warranty covers the cost of part s required to restore this product to proper operating condition and an allowance for labor when provided by a DESA Heating LLC Authorized Service Center or a provider approved by DESA Heating LLC Warranty parts must be obtained through authorized dealers of this prod uct and or DESA Heating LLC who will provide original factory replacement parts Failure to use original factory replacement parts voids this warranty Travel handling transportation diagnostic material labor and incidental costs associated with warranty repairs unless expressly covered by this warranty are not reimbursable under this warranty and are the responsibility of the owner Excluded from this warranty are products or parts that fail or become damaged due to misuse accidents improper installation lack of proper maintenance tampering or alteration s This is DESA Heating LLC s exclusive warranty and to the full extent allowed by law this express warranty excludes any and all other warranties express or implied written or verbal and limits the duration of any and all implied warranties including warranties of merchantability and fitness for a particular purpose to one 1 year on new products and 30 days on factory reconditioned products from the date of first purchase DESA Heating LLC makes no other warranties regard
12. ace remote control and or sensor Fireplace will not come on when switch is flipped to ON 1 Control failure 2 Breaker tripped 1 Call a qualified service tech nician to replace control 2 Reset breaker Heater does not provide heat when turned on 122663 01D 1 Thermal switch has been tripped 2 Circuit breaker has been tripped 3 Wiring is loose Heater is defective Thermostat cycled off o www desatech com 1 Turn unit off Turn off power to unit for 5 minutes Turn power and unit on 2 Turn off circuit breaker that supplies electricity to unit Wait 5 minutes then flip circuit breaker back on 3 Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary Replace heater 5 Change to higher setting A 15 REPLACEMENT PARTS Note Use only original replacement parts This will protect your warranty coverage for parts replaced under warranty PARTS UNDER WARRANTY Contact authorized dealers of this product If they can t supply original replacement part s call DESA Heating LLC at 1 866 672 6040 When calling DESA Heating LLC have ready your name your address model and serial numbers of your heater how heater was malfunctioning purchase date TECHNICAL SERVICE You may have further questions about installa tion operation or troubleshooting If so con tact DESA Heating LLC at 1 866 672 6040 When calling
13. ally open Using a Phillips screwdriver loosen hold down screws on spring clips see Figure 12 8 Close both doors until evenly joined at middle and note gap as measured to outer edges of front face 9 Reopen each door one at a time and retighten the hold down screw while pre serving noted gap at each edge 10 Repeat process until both doors are even ly joined spaced and working freely 8 www desatech com y Spring Clip Press Spring Clip sip Release Pivot Pin Fold Bifold Door After Releasing Spring Clip to Slide Door Out of Upper Track Remove Pivot Pin From Bottom Face While Sliding Door Out of Upper Track 4 Pivot Pin Figure 11 Installing Removing Glass Doors Side Front Face Spring Clip Partially Opened Figure 12 Adjust Glass Door 122663 01D ACCESSORY INSTALLATION Continued Removing Bifold Glass Doors 2 Fully fold frame assembly and slide upper Bifold doors may be removed for replacing edge towards center of firebox opening or cleaning until the guide pins are free of the frame 1 Partially open each door and press up on rail see Figure 11 page 8 upper spring clip with a screw driver until outer top pivot pin is free of the clip CLEANING A CLEANING BACK SCREEN GLASS WARNING Always discon 1 The glass is cleaned in the factory during nect power and allow the heater assembly During shipment installation to c
14. aution is necessary when any heater is used by or near children or inva lids and whenever heater is left operating and unattended 5 Always unplug heater when not in use 6 Donotoperate any heater with a damaged cord or plug or if heater malfunctions or has been dropped or damaged in any way Return heater to authorized service facility for examination electrical or mechanical adjustment or repair 7 Do not use outdoors 8 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 9 Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 10 To disconnect heater turn controls to the OFF before removing plug from outlet turn off power to unit 11 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater 12 To prevent possible fire do not block air intakes in any manner Do not use on soft surfaces like a bed where openings may become blocked 13 Connect to properly grounded circuits only 122663 01D SAFETY Continued 14 A heater has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable liquids or vapors are used or stored 15 Use this heater only as de
15. connect wires to blower heater assem bly see Wiring Diagram page 14 8 Follow steps 8 through 13 under Service Preparation page 10 Brackets Figure 20 Removing Blower Blower Assembly 122663 01D SERVICING Continued BACKLIGHT LED STRIP 1 2 Follovv steps 1 through 4 under Service Preparation page 10 Disconnect vvires from backlight LED strip Squeeze top of standoffs to remove back light LED strip and discard Place new backlight LED strip onto stand offs and push gently Connect wires to backlight LED strip see Wiring Diagram page 14 Follow steps 11 through 13 under Service Preparation page 10 Backlight LED Strip Standoffs Figure 21 Replacing Backlight LED Strip REMOTE CONTROL SENSOR m 2 122663 01D Follovv steps 1 through 6 under Service Preparation page 10 Disconnect vvire from remote control sen sor board Remote Control Sensor s Figure 22 Replacing Remote Control Sensor n 3 Squeeze top of standoffs to remove board 4 Gently push new board onto standoffs 5 Connect vvires to remote sensor board 6 Follow steps 8 through 13 under Service Preparation page 10 SETTINGS CONTROL BOARD 1 Follovv steps 1 through 6 under Service Preparation page 10 2 Disconnect vvire from settings control board 3 Remove screws from bracket to remove settings control board see Figure 23 4 Place new settings
16. control board into posi tion making sure each control is aligned with slot in panel Install using screws from step 3 DO NOT overtighten This will damage control board 5 Reconnect wire to settings control board see Wiring Diagram page 14 6 Follow steps 8 through 13 under Service Preparation page 10 Settings Control Figure 23 Replacing Settings Control Board www desatech com 13 WIRING DIAGRAM yoelq pay Keg usalg eq umolg MOIISA ajdind A quiassy 100 A quassy Jung 0371 juowea y Buyesy Remote Control Infrared Sensor VA AYOOYO 5 pueog 1400 L v 198 0006 9600 06 4 N d 5 6 5 1 41 NOILONNA ANY 0408 824 INVHOVIA 1 21310313 YITNA 96 PUE ZE sowo AHF UOHAS 4104004 1840 oe E eld u 19 MEG UO 910390 a pay aBUBIO DYO yun Bnidun synu anig Tl pela Ta H e Sul pue Keisy 0981 SHUM LHM ade eq hee 9 yenno umosg Mua f UMOJg OJO 2075 p snun e 13409 N A yoeld ad n z x9e g MOJI A MIA ONINGVM eldind Toum UM 0N DV 2 BENOA DV A0ZCI LA xog uon unr xog uon unr 122663 01D www desatech com 14 TROUBLESHOOTING A WARNING Turn off appliance and let cool before servicing Only a qualified service person sho
17. der Service Preparation page 10 LED DRUM AND MOTOR FLAME GENERATION 1 Follow steps 1 through 6 under Service Preparation page 10 2 Disconnect wires from motor and LED drum assembly 3 Remove screws from bottom panel to remove assembly see Figure 16 4 If motor on assembly fails loosen clamps see Figure 16 Remove screws from motor Hold universal joint while removing motor and discard 5 Install new motor Slide motor shaft into universal joint and tighten clamps 6 Hold LED drum assembly in place on bottom panel and replace screws Red LED Drum Assembly Figure 16 Flame Generation LED Drum Assembly T Reattach wires to motor and LED drum Note LED drum wires are polarity sensi tive and must be connected correctly White wire plugs onto left terminal and red wire plugs onto right terminal Motor wires can be connected to either terminal Follow steps 8 through 13 under Service Preparation page 10 MAIN CONTROL BOARD 1 Follovv steps 1 through 6 under Service Preparation page 10 Disconnect vvires to main control board Squeeze top of standoffs to remove main control board and discard Install new control board by gently pushing onto standoffs Reconnect vvires to main control board see Wiring Diagram page 14 Follow steps 8 through 13 under Service Preparation page 10 Transformer Main Control Board bi Y Figure 17 Control Board 122663
18. e is in operation A junction box is provided to hard wire unit to either a 15 amp 120 60 or 20 amp 240 60 120 Volt 60 Hz grounded circuit OPERATION The controls see Figure 8 are located behind hinged control panel door If using heater con trol panel door will be hot during and imme diately after operation Open door by pulling control panel door on left and right side 1 Connect fireplace to povver source Turn on lighted power switch see Figure 8 2 Adiust Flame Ember Backlight Heater to desired settings using the control pad on fireplace Figure 8 or remote control Figure 9 Figure 10 page 8 shovvs fire place settings available Default settings are circled Press control pad or remote control buttons once and release to adiust settings Note When on ember bed will lighten and darken automatically to simulate real embers 122663 01D Heater Flame Ember Backlight Control Control Control Control EH O O El 2 0 0 Heater Flame Ember Backlight Lighted Power Switch Pawan Figure 8 Controls For Electric Fireplace EMBER BACKLIGHT HEATER Figure 9 Remote Control For Electric Fireplace www desatech com 7 OPERATION Continued The heater is pre set to the following temperatures HIGH will shut off when room reaches approximately 86 F 30 C MEDIUM will shut off when room reaches approximately 79 F 26 C LOW will shut off when room reaches
19. e 14 Removing Screen Rod Assembly REPLACING EMBER STRIP le 2 Follow steps 1 and 4 under Replacing Log page 9 Locate ember LED strip see Figure 13 page 9 Disconnect wire right side Remove ember LED strip by squeezing top of standoffs and discard Being careful not to break LED strip press new ember LED strip onto standoffs Reconnect wire to LED strip Follow steps 5 through 7 under Replacing Log page 9 SERVICE PREPARATION Perform steps 1 through 4 below then locate part that needs replacing in the instructions that follow 1 Open control panel door Turn off power to unit circuit breaker so that screen glass seats into glass retainer 10 Reinstall screws from step 5 11 Reinstall log 12 Reinstall screws into brackets to secure 1 log 3 Close screens and doors 14 Turn on power to unit circuit breaker S Control E Panel Door Top Panel creen Glass Figure 15 Removing Screen Glass all parts not shown for clarity www desatech com 122663 01D SERVICING Continued SCREEN GLASS 1 n the event of glass breakage vacuum all remaining glass pieces with a shop vac DO NOT VACUUM WHILE PIECES ARE HOT Replace glass only with replacement part specifically for this heater Never substitute material Only fully tempered soda lime safety glass may be used on this heater 2 Remove and replace glass follow steps 1 through 13 skip step 7 un
20. ed malfunctioned If you suspect to either a 120 60 or 240 60 volt supply the unit is damaged return the A CAUTION The unit must unit to an authorized service be connected to a properly facility for examination electri grounded and protected 120 240 Ca or mechanical adjustment volt circuits Always use ground or repair fault protection where required by the electrical code LOCATING FIREPLACE WARNING Due to high tem NOTICE Minimum and maximum peratures this heater should be located out of traffic Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9 m from the front of the heater clearances mustbe maintained at all times Illustrations throughout these instructions reflect typical installations and are for design purposes only Actual installa tions may vary slightly due to individual preferences WARNING Never locate this heater where it may fall into a bath tub or other water container WARNING To prevent contact with sagging or loose insulation the heater must not beinstalled against vapor barrier or exposed insulation Localized overheating could occur and a fire could result www desatech com 122663 01D LOCATING FIREPLACE Continued A CAUTION Do notexpose the heater to the elements such as rain etc Al CAUTION Wear gloves and safety glass
21. es for protection during installation and main tenance Plan where to locate and frame fireplace Before installation consider the following 1 Fireplace location must allow for wall and ceiling clearances see Installation Clear ances 2 Fireplace screen should not be exposed to direct sunlight from windows or doors 3 Unit can be wired for either 120 60 15 amp circuit or 240 60 20 amp circuit A dedicated circuit should be provided to avoid circuit breaker trips or blown fuses Flush Installations are recommended where living space is limited or at a premium Since space required to enclose fireplace would be located beyond an outside wall this in stallation would require additional planning and construction Check local codes for any restrictions Projected Installations can extend any dis tance into room A projection may be ideal for a new addition on an existing finished wall Corner Installations make use of space that may not normally be used and provides a wider and more efficient viewing angle and heat distribution Internal Wall Installations provide a discrete option for room separation and can also be an ideal addition to an existing wall Internal Wall Corner Installation Installation Ly 1 Full Projection Installation Flush Installation 44 de Figure 3 Possible Installation Locations 122663 01D www desatech com INSTALLATION INSTALLATIO
22. he informa tion in these instructions is not followed exactly a fire or explosion may result causing property damage personal in jury or death Do not store or use gasoline or other flammable vapors in the vi cinity of this or any other heater A junction box is provided to hard wire unit to either a 15 amp 120 60 or 20 amp 240 60 120 Volt 60 Hz grounded circuit Tools and building supplies required for installation Saw Square e Pliers e Gloves e Hammer e Level e Phillips screwdriver Surround e Framing materials e Electric drill bits Tape measure e Wall finishing materials e Caulking material AX CAUTION Provide adequate clearances around the air open ings and adequate accessibility clearances for servicing and proper operations 6 www desatech com WARNING Control panel door on this heater cannot in any way be covered as it may create a fire hazard BUILT IN INSTALLATION Built in installations require a framed enclo sure constructed of 2 x 4 or heavier lumber and sized in accordance with Figure 6 This allows unit to slide into opening and be nailed to stud at sides and top nailing flanges These flanges accept 5 8 drywall or plywood board to finish unit flush to face Optional trim ac cessories are available that will extend 1 2 over rough edge of wall opening see Acces sories page 17 IMPORTANT If installing a perimeter trim kit you must
23. ing this product DESA Heating LLC s liability is limited to the purchase price of the product and DESA Heating LLC shall not be liable for any other damages whatsoever under any circumstances including indirect incidental or consequential damages Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state For information about this warranty contact DESA 122663 01 DESA Heating LLC 2701 Industrial Drive Bowling Green KY 42101 122663 01 www desatech com Rev D NOT A UPC 1 866 672 6040 06 08
24. ool before performing any handling etc glass surface may collect cleaning maintenance orreloca dust particles These can be removed by buffing lightly with a clean damp cloth water only Glass should be completely dried with a lint free cloth or paper towel To access glass to clean follow steps tion of this heater Turn controls to OFF and remove plug from outlet or turn off circuit breaker 5 to heater 1 through 5 under Service Preparation page 10 CLEANING FIREBOX 3 Using gloves gently remove glass panel 1 Open bi fold doors and screens by sliding it toward you There is a rubber 2 Using a brush vacuum attachment gently bumper on each corner of glass clean compartment 4 Clean glass as instructed in step 1 3 Close screens and doors 5 Follow steps 8 through 13 under Service Preparation page 10 SERVICING A 6 Install new log WARNING Turn offappliance 7 Reinstall screws into brackets to secure and let cool before servicing new log Only a qualified service per 8 Close screens and doors son should service and repair heater For questions regarding replacing parts see page 13 Note All service procedures are performed through front face opening of fireplace REPLACING LOG y 1 Turn off power to unit circuit breaker ISSO x 2 Open upper control panel door Turn n SS m power switch off S a SS 3 Open bi fold doors if equipped and Sy screens Log Ember 1
25. scribed in this manual Any other use not recommended by the manufacturer may cause fire elec tric shock or injury to persons 16 Avoid the use of an extension cord be cause the extension cord may overheat and cause a risk of fire However if you have to use an extension cord the cord should be No 14 AWG minimum size and rated not less than 1875 WATTS 17 Always use ground fault protection where required by electrical codes 18 Always disconnect power before perform ing any cleaning maintenance or reloca tion of heater 19 To prevent a possible fire do not burn wood or other materials in this heater 20 To prevent electric shock or fire always use a certified electrician should new circuits or outlets be required 21 When transporting or storing heater keep in a dry place 22 Control panel door gets hot during heater operation To open control panel door gently pull on left and right outer edges Do not open from center of control panel door LISTING APPROVALS This heater has been tested in accordance with the CSA Standards for fixed and loca tion dedicated electric room heaters in the United States All components are UL or CSA safety certified If you need assistance during installation please contact your local dealer or the DESA Heating LLC at 1 866 672 6040 Please have the distributor s model and serial numbers when you call Description 36 Fireplace Voltage 120 240
26. uct or identification tag Serial No located on product or identification tag Date Purchased Keep receipt for warranty verification DESA HEATING LLC LIMITED WARRANTIES New Products Standard Warranty DESA Heating LLC warrants this new product and any parts thereof to be free from defects in material and workmanship for a period of one 1 year from the date of first purchase from an authorized dealer provided the product has been installed maintained and operated in accordance with DESA Heating LLC s warnings and instructions For products purchased for commercial industrial or rental usage this warranty is limited to 90 days from the date of first purchase Factory Reconditioned Products Limited Warranty DESA Heating LLC warrants factory reconditioned products and any parts thereof to be free from defects in material and workmanship for 30 days from the date of first purchase from an authorized dealer provided the product has been installed maintained and operated in accordance with DESA Heating LLC s warnings and instructions Terms Common to All Warranties The following terms apply to all of the above warranties Always specify model number and serial number when contacting the manufacturer To make a claim under this warranty the bill of sale or other proof of purchase must be presented This warranty is extended only to the original retail purchaser when purchased from an authorized dealer and only when installed by
27. uld service and repair heater OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Fireplace turns off and will not turn on 1 Fireplace has overheated and safety device has caused thermal switch to disconnect or home circuit breaker has opened 1 Reset switch by turning main power switch off and waiting 5 minutes then turn ing it back on or reset circuit breaker Flame is not moving 1 Loose wiring 2 Flame motor defective 1 Inspect wiring for loose connections 2 Calla qualified service techni cian to replace flame motor Flame is not visible 1 Wiring is loose 1 Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary Log set and or ember is not glowing 1 Wiring is loose 1 Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary Flame sputters flashes 1 Flame motor is defective 2 Flame generation contacts dirty obstructed 1 Call a qualified service techni cian to replace flame motor 2 Disconnect power Fol low steps to replace flame generation LED Clean contacts with dry cloth Remote control does not work 1 Low batteries 2 Not aiming control cor rectly 3 Defective remote control and or sensor 1 Replace AAA batteries in remote control 2 Aim control at sensor lo cated directly behind glass screen in center of unit just above logs 3 Repl
Download Pdf Manuals
Related Search