Crestron electronic TPS-6X-BTP User's Manual
Contents
1. battery Storing the battery in a charged state will not increase the maximum storage period in the storage time table e The energy storage capability of the battery negative electrode will be decreased if the battery is allowed to completely self discharge Therefore it is important to cycle NiMH batteries that have been stored for extended periods before use e Ifthe batteries are cycled charged and discharged the storage capability will be restored up to 95 of its initial rated capacity after the second or third cycle Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 11 Battery Pack for TPS 6X Crestron TPS 6X BTP To prolong the life and maintain the performance of your NiMH batteries Crestron recommends you follow these steps e Practice FIFO First In and First Out inventory rotation e Never store batteries under load e Store batteries in a temperature controlled environment refer to table below e Store batteries at 65 20 relative humidity and keep out of direct sunlight e Cycle batteries at least one charge discharge cycle according to the table below NiMH Battery Storage Time TEMPERATURE RANGE BATTERY OR PACK MAXIMUM STORAGE PERIOD CYCLE INTERVAL 104 to 122 F 40 to 50 C Less than 30 days 86 to 103 F 30 to 39 C 30 to 90 days 4 to 85 F 20 to 29 C 91 to 180 days Disposal NOTE The TPS 6X BTP contains Nickel Metal Hydride NiMH batte2. existing TPS 6X BTP from a TPS 6X touchpanel A 1 Phillips screwdriver and a small slot head screwdriver are required 1 Remove power from the touchpanel use the included T pin to slide the battery switch on the rear to the OFF down position and place the touchpanel face down on a clean padded work surface Refer to illustration below Bottom View Showing Battery Switch and Screw Locations Screws Screws 4 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X 2 Remove the four screws that secure the front bezel to the touchpanel and return the unit to its normal face up position Use care and hold the bezel to the rest of the touchpanel If the bezel separates from the rest of the touchpanel while rotating the unit to its normal position the internal parts of the panel may spill out 3 Lift the front bezel from the touchpanel then place the touchpanel assembly face down on the work surface 4 Carefully remove the rear of the enclosure from the touchpanel by grasping the support frame at the left and right edges gently spreading them as shown in the illustration below and lifting the assembly It will snap out of the enclosure Removing Rear Enclosure from TPS 6X Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 5 Battery Pack for TPS 6X Crestron TPS 6X BTP 5 Remove t
3. 5 to 3 hours when in use Optimal Operating 32 to 112 F 0 to 45 C Temperature 50 to 104 F 10 to 40 C when charging Weight 4 3 oz 120 2 g NOTE The batteries will not charge when they are warmer than the maximum charging temperature This may occur due to extended use of the panel while on the TPS 6X DS or TPS 6X DS C Docking Station To cool the batteries turn off power to the touchpanel using the left trigger key The touchpanel will cool faster 1f it is removed from the TPS 6X DS or TPS 6X DS C before it is turned off The panel will be cool in approximately 20 minutes 2 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X Physical Description The TPS 6X BTP consists of two battery cells along with the integrated wiring It has a multi pin connector for attachment inside the TPS 6X TPS 6X BTP Physical View Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 3 Battery Pack for TPS 6X Crestron TPS 6X BTP Setup Removal NOTE The TPS 6X Wireless Touchpanel contains ESD electrostatic discharge sensitive devices To avoid damaging the unit perform the following procedure while wearing a grounding strap that is properly grounded or on a grounded workstation NOTE To prevent damage to the multi pin connector and wiring use care when handling the TPS 6X BTP Perform the following procedure to remove the
4. Battery Pack for TPS 6X TPS 6X BTP e 13 Battery Pack for TPS 6X Crestron TPS 6X BTP Future Updates As Crestron improves functions adds new features and extends the capabilities of the TPS 6X BTP additional information may be made available as manual updates These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision Check the Crestron website periodically for manual update availability and its relevance Updates are identified as an Addendum in the Download column 14 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X Return and Warranty Policies Merchandise Returns Repair Service 1 No merchandise may be returned for credit exchange or service without prior authorization from CRESTRON To obtain warranty service for CRESTRON products contact an authorized CRESTRON dealer Only authorized CRESTRON dealers may contact the factory and request an RMA Return Merchandise Authorization number Enclose a note specifying the nature of the problem name and phone number of contact person RMA number and return address 2 Products may be returned for credit exchange or service with a CRESTRON Return Merchandise Authorization RMA number Authorized returns must be shipped freight prepaid to CRESTRON 6 Volvo Drive Rockleigh N J or its authorized subsidiaries with RMA number
5. Crestron TPS 6X BTP Battery Pack for TPS 6X Installation Guide This document was prepared and written by the Technical Documentation department at T CRESTRON Crestron Electronics Inc 15 Volvo Drive Rockleigh NJ 07647 1 888 CRESTRON All brand names product names and trademarks are the property of their respective owners 2008 Crestron Electronics Inc Crestron TPS 6X BTP Battery Pack for TPS 6X Contents Battery Pack for TPS 6X TPS 6X BTP 1 AH RO ELTE A OVA po act weirs elton EE S ce chased A E AA O AAE E E l Feature sand FUNCIONS riora rann aA E A T areas l KRI RTT 2 PAY SiC Al DESCH PON 8 oda sae ae a A a hse 3 61 TTT 4 R O TTT 4 NST AM a TT 8 CHA OI es harshisn pera acts sa alraas eee eas ads rane ac eh ou eae eee eee ota es 11 BLO Osa ane Pea crasgo ca eae ta oases ats aoe eeiae saccene seca aoe Goat moeneesecieeseeese nee see eetetae 11 DEDOS esinen a E eee eae 12 IT E E E a ce teteenssouceonse 13 lndustry eT e 13 Reference R e T cx ssocissiicecss tg tenaisecehdeisounsatdereaedere erases asonsa careers 13 We Me Tih ts MAIN GS setae coche sc A ace hues E E E A ase ce E E E A EE ae tetsease 13 Sn U deS ec Peete os ae a ed a a a ease caueedbaseateatene edeads 14 Return anid Warranty e RL 15 Merchandise Returns Repair Service esse 15 CRESTRON T imited Warranty TT 15 Installation Guide DOC 6740A Contents e i Crestron TPS 6X BTP Battery Pack for TPS 6X Battery Pack for TPS 6X TPS 6X BT
6. P Introduction The Crestron TPS 6X BTP is a replacement NiMH rechargeable battery pack for the TPS 6X Wireless Touchpanel One TPS 6X BTP is included with each TPS 6X Installation of the TPS 6X BTP battery pack requires tools and should be performed by a qualified technician Features and Functions Replacement NiMH rechargeable battery pack for the TPS 6X Wireless Touchpanel Fast charging Nickel Metal Hydride batteries Can be charged when the TPS 6X is mounted in the TPS 6X DS or TPS 6X DS C Docking Station TPS 6X DS C sold separately NOTE For more information on the TPS 6X Wireless Touchpanel refer to the latest version of the TPS 6X Operations Guide Doc 6575 which is available from the Crestron website www crestron com manuals NOTE For more information on the TPS 6X DS or TPS 6X DS C Docking Stations refer to the latest version of the TPS 6X DS or TPS 6X DS C Operations Guides Doc 6576 and Doc 6707 respectively Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 1 Battery Pack for TPS 6X Crestron TPS 6X BTP Specifications Specifications for the TPS 6X BTP are listed in the following table TPS 6X BTP Specifications SPECIFICATION DETAILS Output Voltage 4 8 Volts DC Capacity 2000 mAh Composition Nickel Metal Hydride NiMH Usage Per Charge 2 hours continuous 24 hours under normal use 10 active duty cycle with standby powerdown activated Charging Time 2 5 hours 2
7. TPS 6X BTP so the black and white wires are on the left side bottom and the red and yellow wires are on the right side bottom as shown in the illustration below TPS 6X BTP Orientation 2 Place the battery cells in their compartments on the left and right sides of the TPS 6X assembly ensuring the ridge that runs along the length of each cell is facing inward toward the center of the assembly and the rounded side of each cell is facing outward 8 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X 3 Carefully connect the multi pin connector of the TPS 6X BTP with the corresponding connector on the circuit board of the TPS 6X 4 Dress the cables of the TPS 6X BTP as shown in the illustration below and apply the 2 inch 50 mm piece of orange tape that came with the TPS 6X BTP to hold the wires in place 5 Apply the two 1 inch 25 mm pieces of orange tape that came with the TPS 6X BTP to each battery cell extending the tape to the black tab of the battery housing support on each side as shown in the illustration below These replace the clear tape that held the original cells in place NOTE Ensure the tape does not wrap around to the front of the touchpanel where it could contact the light fibers on either side of the screen TPS 6X Assembly Cables Dressed Orange Tape Applied Battery Cells HELIER E uo Ti R15 fs i 4 GEE L T s i R155 SS E R pe C b
8. clearly marked on the outside of all cartons Shipments arriving freight collect or without an RMA number shall be subject to refusal CRESTRON reserves the right in its sole and absolute discretion to charge a 15 restocking fee plus shipping costs on any products returned with an RMA 3 Return freight charges following repair of items under warranty shall be paid by CRESTRON shipping by standard ground carrier In the event repairs are found to be non warranty return freight costs shall be paid by the purchaser CRESTRON Limited Warranty CRESTRON ELECTRONICS Inc warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three 3 years from the date of purchase from CRESTRON with the following exceptions disk drives and any other moving or rotating mechanical parts pan tilt heads and power supplies are covered for a period of one 1 year touchscreen display and overlay components are covered for 90 days batteries and incandescent lamps are not covered This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer Purchasers should inquire of the dealer regarding the nature and extent of the dealer s warranty if any CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended or if it has been subjected to misuse accidental damage modificat
9. he orange tape securing the battery pack wires to the circuit board and the two pieces of clear tape on each battery cell Refer to illustration below TPS 6X Assembly Removed from Enclosure Battery Cells porr RTS E fia Connector Orange Tape Clear Tape 6 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X 6 Using the flat end of a small slot head screwdriver gently separate the multi pin connector from the corresponding connector on the circuit board of the TPS 6X Refer to illustration below TPS 6X BTP Connector on TPS 6X Bi x k 2 s r P EEE E dibui N ap yt i UE Rha edt biada N 2 E S ri 7 N 7 ee aa Connector 7 Remove battery cells with the connecting wires attached from either side of the assembly Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 7 Battery Pack for TPS 6X Crestron TPS 6X BTP Installation NOTE The TPS 6X Wireless Touchpanel contains ESD electrostatic discharge sensitive devices To avoid damaging the unit perform the following procedure while wearing a grounding strap that is properly grounded or on a grounded workstation After completing removal of the old TPS 6X BTP from the TPS 6X touchpanel refer to Removal on page 4 perform the following procedure to install the new TPS 6X BTP A 1 Phillips screwdriver is required 1 Orient the
10. ion or improper installation procedures Furthermore this warranty does not cover any product that has had the serial number altered defaced or removed This warranty shall be the sole and exclusive remedy to the original purchaser In no event shall CRESTRON be liable for incidental or consequential damages of any kind property or economic damages inclusive arising from the sale or use of this equipment CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party CRESTRON shall at its option repair or replace any product found defective without charge for parts or labor Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty Except as expressly set forth in this warranty CRESTRON makes no other warranties expressed or implied nor authorizes any other party to offer any warranty including any implied warranties of merchantability or fitness for a particular purpose Any implied warranties that may be imposed by law are limited to the terms of this limited warranty This warranty statement supersedes all previous warranties Trademark Information All brand names product names and trademarks are the sole property of their respective owners Windows is a registered trademark of Microsoft Corporation Windows 95 98 Me XP Vista and WindowsNT 2000 are trademarks of Microsoft Corporation Installation Guide DOC 6740A Bat
11. nstallation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X Charging NOTE A Nickel Metal Hydride NiMH battery typically provides 500 charge discharge cycles To charge the TPS 6X BTP install the TPS 6X BTP in a TPS 6X touchpanel and mount the touchpanel on a powered TPS 6X DS or TPS 6X DS C Docking Station Charger TPS 6X DS C sold separately NOTE The battery pack may take up to three hours to charge in a powered touchpanel if the panel is in use during charging Storage Over time the capacity and voltage of rechargeable Nickel Metal Hydride NiMH batteries will decrease if the batteries are not recharged at regular intervals This 1s caused by a chemical reaction that takes place within the batteries commonly known as self discharge Temperature is a major factor affecting the rate of self discharge of the battery when placed in storage Higher temperatures will increase the rate of self discharge The storage time table on the following page shows how long it will take NiMH batteries to self discharge at different storage temperatures After the allotted time in storage the batteries will need to be cycled charged and discharged to prevent permanent damage to the batteries NiMH batteries and packs can be stored at any state of charge The information in the storage time table is valid for batteries in any state of charge A fully discharged battery will last as long in storage as a fully charged
12. ry cells When the unit can no longer retain a charge it must be recycled or disposed of properly Follow local ordinances and or regulations for disposal 12 e Battery Pack for TPS 6X TPS 6X BTP Installation Guide DOC 6740A Crestron TPS 6X BTP Battery Pack for TPS 6X Resources Industry Compliance As of the date of manufacture the TPS 6X BTP has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling CEC Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website www crestron com manuals This link will provide a list of product manuals arranged in alphabetical order by model number List of Related Reference Documents DOCUMENT TITLE TPS 6X Isys 5 7 Wireless Touchpanel TPS 6X DS Docking Station for the TPS 6X TPS 6X DS C Docking Station for the TPS 6X Further Inquiries If you cannot locate specific information or have questions after reviewing this guide please take advantage of Crestron s award winning customer service team by calling Crestron at 1 888 CRESTRON 1 888 273 7876 You can also log onto the online help section of the Crestron website www crestron com onlinehelp to ask questions about Crestron products First time users will need to establish a user account to fully benefit from all available features Installation Guide DOC 6740A
13. s s C1890 l ig O B ie eee DEl ag baci pe cy amp arti L le RAS N p i Sh ZK LE k o Ti l wae ea E S Yi 1 Pacis es RISS A ato aie ie Pi f T oof Tay a IBI HITA pany S ret MUTT g 299 kav T l RE Dp Soe Rios QK aaia p Orange Tape Installation Guide DOC 6740A Battery Pack for TPS 6X TPS 6X BTP e 9 Battery Pack for TPS 6X Crestron TPS 6X BTP 6 Carefully turn the assembly over returning it to its normal face up position Then place the assembly into the rear half of the TPS 6X enclosure hinging it so the top of the assembly is in place first as shown in the illustration below Then settle the bottom of the assembly into place and with your thumbs on the black plastic at the left and right edges press and snap the assembly into place Installation Showing Top of Assembly in Place 7 Position the front bezel over the exposed touchpanel ensuring the ribbon cables remain tucked in place and the fiber optic cables remain inboard of the posts located next to each of the bottom screw holes 8 Hold the bezel to the rest of the touchpanel and carefully rotate the entire panel onto its face once more 9 Reinstall the four screws to secure the bezel to the touchpanel Tighten the screws being careful not to strip the threads 10 Re connect power slide the battery switch on the rear to the ON up position 10 e Battery Pack for TPS 6X TPS 6X BTP I
14. tery Pack for TPS 6X TPS 6X BTP e 15 T CRESTRON Crestron Electronics Inc Installation Guide DOC 6740A 15 Volvo Drive Rockleigh NJ 07647 2022218 Tel 888 CRESTRON 10 08 Fax 201 767 7576 Specifications subject to www crestron com change without notice
Download Pdf Manuals
Related Search