Craftsman Digital Torpedo Level Owner's Manual
Contents
1. up to 0 1 accuracy e Measures any slope in percent e Measures level and plumb with either the LCD digital display or with the vertical and horizontal bubble vials NOTE Install 2 AAA 1 5 volt batteries sold separately to power the LCD module display of this digital level See BATTERY INSTALLATION section 1 OA button Press the button to turn the LCD display screen on off and to turn the sound on and off 2 LCD Display Large easy to read display screen reads right side up even when the level is upside down 3 Hold Button Press this button in order to freeze and unfreeze the display reading 4 Zero Button Absolute relative angle conversion for the comparison of two work surface angles 5 Convert Button Use this button to convert measurements to different units 48295 Manual_Revised_07 0620 Page 4 6 Bubble Vials For visual determination of level and plumb V groove in working base For use on curved and angled surfaces Magnetic base with V groove Four magnets in the working base allow for secure contact to metal handy when working with steel studs or metal ductwork 9 Battery compartment Holds two AAA batteries to power the LCD display TECHNICAL SPECIFICATIONS Recommended Use Indoors or Outdoors Power supply Two AAA 1 5 volt batteries Angle Measuring Range 0 360 Optimum Operating Temperature 0 to 40 C 32 to 104 F Accuracy2. 2 Take a measurement of the first work surface the LCD screen indicates the angle between that surface and true level 3 Press the zero button for the relative angle mode and the level will set the first angle to zero 4 Move the digital level to the second work surface and the LCD screen indicates the relative angle between the first and second surfaces 5 To return to absolute angle again turn the power button off and back on Convert Button Converts the angle display on the LCD screen among 3 different units e Press the button to proceed through the display units Degrees Slope and Pitch in ft e Pitch readings are in increments of 1 8 in per ft Plus and minus signs indicate whether the pitch is slightly more or slightly less than the pitch that is shown on the display Hold Button To hold the information of the current reading press the Hold button to freeze the displayed reading press it again to return to measuring mode TO USE THE LEVEL FOR HORIZONTAL AND PLUMB MEASUREMENTS Horizontal and Plumb measurements can be made with both the bubble vial and the LCD display features Horizontal e Use the level on horizontal surfaces to determine when they are level Place the level against the horizontal surface The surface will be at true level when the bubble is positioned exactly between the marks on the level vial e The LCD display represents the surface you are measuring as a line eith
3. Product Manual CRAFTSMAN 7 in Digital Multi function DIGITAL LEVEL Model No 320 48295 e Warranty A CAUTION Read understand and e Safety follow all Safety Rules and Operating e Description Instructions in this Manual before e Operation using this product e Maintenance e Troubleshooting Sears Roebuck and Co Hoffman Estates IL 60179 www craftsman com TABLE OF CONTENTS ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails to give complete satisfaction within one year from the date of purchase return it to any Sears store or other Craftsman Outlet in the United States for free replacement This warranty does not include expendable parts such as blades and lamps This warranty applies for only 90 days from the date of purchase if this product is ever used for commercial or rental purposes This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co Hoffman Estates IL 60179 SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS 48295 Manual Revised 07 0620 Page 2 SAFETY INSTRUCTIONS e Be sure to read and understand all instructions in this manual before us ing this digital level Failure to follow all instructions may result electric shock fire and or serious personal injury e Always use two AAA size batteries Use of any other batteries may create a risk of fire
4. e Insert the batteries correctly Match the polarities positive to positive and negative to negative as marked on the inside of the battery compartment e Do not short circuit the battery terminals e Do not mix old and new batteries If the batteries are weak replace both of them with two new batteries The batteries should match each other in brand and type e Remove dead batteries immediately and dispose of them according to lo cal ordinances e Never dispose of batteries in fire e Keep batteries out of the reach of children They are not playthings e Remove batteries and store them separately if the level will not be used for several days e Do not attempt to repair or disassemble the digital level Any repair required on this product should be performed by authorized service center personnel DESCRIPTION KNOW YOUR LEVEL Fig 1 Power Beeper Activate Button Convert Button Zero Button LCD Display Screen Hold Button 48295 Manual_Revised_07 0620 Page 3 Bubble Vial Battery compartment Bubble Vial Magnet Magnet Magnet Working base Magnet This Craftsman 7 inch Digital Level is a highly versatile leveling tool designed for fast easy operation e Heavy duty lightweight aluminum construction e LCD digital module is constructed of unbreakable ABS polymer sealed against dirt e Acrylic block bubble vials e Measures in degrees with
5. e installed e Reinstall batteries with incorrectly correct polarity The LCD screen A e Battery voltage is low e Replace with new batteries will not turn on e The LCD screen is e Take tool to Sears Service damaged Center 48295 Manual Revised 07 0620 Page 10 48295 Manual Revised 07 0620 Page 11 Get it fixed at your home or ours Just Call 1 800 4 MY HOME 1 800 469 4663 24 hours a day 7 days a week For the repair of major brand appliances in your own home no matter who made it no matter who sold it For your nearest Sears Parts 8 Service location to bring in products like vacuums lawn eguipment and electronics For Sears Parts 8 Service to order the replacement parts accessories and owner s manuals that you need to do it yourself www sears ca To purchase or inquire about a Sears Maintenance Agreement call 1 800 361 6665 9 a m 8 p m Mon Fri EST 9 a m 4 p m Sat Pour service en francais 1 800 LE FOYER 1 800 533 6937 www seals ca Sears ealn 9 TM Trademarks of Sears Roebuck and Co used under license by Sears Canada Inc wMargue d pos e MCMargue de commerce de Sears Roebuck and Co utilis e en vertu d une licence de Sears Canada Inc
6. er above or below the 0 or true level line with an arrow showing whether the surface should be raised or lowered in order to be level The digital display shows the degree to which the surface is out of level If the sound is turned is on the level will beep when true level or 0 is reached 48295 Manual Revised 07 0620 Page 7 PLUMB Fig 5 e To find the plumb of a work surface place the digital level against the vertical surface with the plumb bubble vial at the top The surface will be at true plumb when the bubble is positioned exactly between the marks on the vial e The LCD display will show the actual angle of the surface 90 is plumb a beep will sound at 90 if the sound function is turned on TO USE THE LEVEL FOR ANGLE MEASUREMENTS Pitch Fig 6 e The digital level can be used to measure pitch for example the pitch of a roof e Pitch is measured in inches of rise per foot of run e The pitch will be read Fig 5 as inches in 1 8 in increments per foot with a or a sign to indicate that the pitch is slightly above or below the displayed measurement Push the convert button to change the display to Pitch mode in ft Angle Fig 7 The digital level measures any angle in degrees with up to 0 1 accuracy If the sound button is turned on the level will beep at the 0 45 90 and last hold angle Push the conv
7. ert button to change the display to Angle mode lt Slope Fig 8 The digital level measures the percent slope of a surface This is useful when laying pipe for proper drainage When the display is in the slope mode it will measure the surface in percent with exact level a 48295 Manual Revised 07 0620 Page 8 0 0 If the sound is turned on the level will beep at 0 0 and 100 Push the convert button to change the display to Slope mode ABSOLUTE AND RELATIVE ANGLE MEASUREMENTS Absolute angle measurement 1 2 Place the digital level on a working surface with the base flat against the surface The display indicates the absolute angle between true level and the working surface The zero line indicates the level position and the arrow indicates the orientation of the working surface either above or below true level To activate the sound briefly press the O A button The level will beep when the level is at 0 level 45 90 plumb and last hold angle Press the Hold button to freeze the display reading To take a new measurement press the hold button again to return to measurement mode Relative angle measurement The relative angle mode allows you to measure the angle of difference between 2 different surfaces 1 2 3 Place the digital level on Surface 1 The LCD screen indicates the absolute angle between true level and Surface 1 Press the ZERO bu
8. of vials 0 029 level or plumb Accuracy of digital display 0 1 level or plumb Estimated battery life 12 hours with 2 AAA alkaline batteries OPERATION BATTERY INSTALLATION Fig 2 This multi function digital level Fig 2 uses two AAA batteries sold separately to power the LCD module display NOTE Always turn off the level before installing or replacing the batteries 1 Open the battery cover located on the back of the level Fig 2 2 Insert two new AAA alkaline batteries with the polarity as indicated on the inside of the battery compartment 3 Securely close the cover LCD DISPLAY AND BUTTON FUNCTIONS LCD screen icons 0 y Up Down Indicator e The zero line 0 indicates the true level e The second line appearing either above or below the 0 line indicates the level s position relative to true level e The arrow indicates the direction in which the level needs to be moved to achieve true level 48295 Manual Revised 07 0620 Page 5 AS Battery Power Icon Indicates the amount of battery power in the unit Replace batteries when the black power bar disappears lt Sound Icon This icon appears on the screen when the sound function is activated H Hold Icon Indicates that the displayed measurement is frozen Button Functions A Button On Off Sound Press the button to turn
9. the LCD display screen on e When the LCD screen first comes on the ambient temperature is displayed in Fahrenheit for approximately 2 seconds to help the user determine whether the level is being used in the optimum temperature range 32 to 104 F e The current angle of the Fig 3 level is then displayed on the LCD screen and a line representing that angle is shown either above or below the line that indicates the position of true level Fig 3 e Briefly press the button once more to activate the sound which will beep when the level is positioned at 0 45 90 and last hold angle to true level e Briefly press the button a third time to turn off the sound Additional brief presses on the button will turn the sound function on and off e An arrow on the display indicates the direction in which the level needs to be moved to reach true level e True level is indicated Fig 4 when the angle line and the level line in the display are together and the angle shows 0 Fig 4 e Turn off the level by pressing the button and holding it in for approximately 3 seconds e The level will shut itself off when it has not been used for 5 minutes 48295 Manual_Revised_07 0620 Page 6 Zero Button Absolute relative angle conversion button for comparison of two work surface angles 1 When the level is first turned on it is in the absolute angle mode and displays the angle from true level
10. tton to activate the relative angle measurement mode The current angle will be considered to be 0 0 and the display will read 0 0 Place the digital level on Surface 2 and the relative angle between Surface 1 and Surface 2 will be displayed The zero line indicates the Surface 1 position and the arrow indicates the orientation of Surface 2 either above or below Surface 1 At this point you can change the display units for the measured angle from degrees to pitch inch foot or slope by pressing the convert button 48295 Manual_Revised_07 0620 Page 9 MAINTENANCE This digital level has been designed to be a low maintenance tool However in order to maintain its performance follow these steps 1 HANDLE the tool with care Treat it as a precision optical device such as a camera or binoculars 2 AVOID exposing the tool to shock continuous vibration or extreme hot or cold temperatures STORE the tool indoors and in a safe place The Level is designed to be weather resistant and construction site tough If the level is splashed with mortar or other construction site residue simply wipe it clean with a damp cloth 5 DO NOT immerse the level in water Aluminum surfaces can be cleaned with a non abrasive powder REMOVE the batteries from the tool if it is not going to be used for an extended period 8 DO NOT attempt to take the level apart TROUBLESHOOTING PROBLEM CAUSE SOLUTION e Batteries ar
Download Pdf Manuals
Related Search