Corega USB ADSL Modem DSLAAU User's Manual
Contents
1. Includes a control panel monitoring program for configuring the adapter and checking the status of the connection on both Windows and Macintosh systems Provides an RJ 11 connector for connection to the telephone line Supports DSL downstream data rates up to 8 Mbps 125 times faster than standard 56K modems Supports DSL upstream data rates up to 1024 kbps Support for PPP over Ethernet PPPoE 2 Hardware Installation DSLAAU Manual 2 1 Before you start In MAC operating systems you need to install the device drivers first see next chapter and then perform the hardware installation steps below Hardware Installation Install corega DSLAAU by following steps with the PC running 1 Insert the rectangular end of a USB cable into the USB port of your PC 2 Insert the square end of the USB cable into the USB port of corega DSLAAU In Windows operating systems corega DSLAAU will be detected and informational messages will be displayed on the PC s screen Proceed with the software installation in the next chapter using the operating system appropriate to you Software Installation The software installation procedures vary depending upon the oper ating system of your PC Be sure to follow the instructions provided for the operating system appropriate for you 3 1 Before you start The following information may be required for software installation Contact your DSL service provider before proc2. INT 4 2000 Intemet QoS Packet Scheduier O File and Printer Sharing for Microsoft Networks This connection uses the following items JS Client for Microsoft Networks Description wide area network Uninstall Properties Transmission Control Protocol intemet Protocol The default protocol that provides communication across diverse interconnected networks DSLAAU Manual 5 Use the Internet Protocol TCP IP Properties window to modify the IP address and DNS Server addresses as follows Internet Protocol TCP IP Properties General 5 a a You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 2 Use the following IP address IP address 192 100 100 59 Jbtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Altemate DNS server e Change the IP address to a user defined address by selecting Use the following IP address click inside the radio button to the left of it and typing the address in the space provided Change the DNS Server addresses to user defined addresses by selecting Use the following DNS server addresses click inside the radio button to the left of it and typing the addresses in the spaces provided The A
3. of the software is an easy process Simply uninstall the existing driv ers See Windows Uninstall section and then install the new drivers See Chapter 3 Software Installation section Note Be sure to follow the instructions provided for the appropriate operating system for your application 5 2 MAC OS 9 x and OS X Drivers Update In order to upgrade corega DSLAAU drivers on the Macintosh simply uninstall the existing drivers see MAC OS 9 x Uninstall or MAC OS X Uninstall section and then install the new drivers see the MAC OS installation instructions or the OS X installation instruc tions Note Be sure to follow the instructions provided for the appropriate operating system for your application corega DSLAAU control panel program provides a quick and easy way to configure and check the performance of the modem and the ADSL connection When open the monitor window updates every 2 seconds O Software Uninstall DSLAAU Manual 6 1 Windows Uninstall Remove corega DSLAAU software drivers by performing the follow ing steps Note The USB cable should not be unplugged until you are prompted to do so From your PC desktop click Start gt Programs gt Corega USB ADSL Modem gt Uninstall 2 A message will be displayed asking you to confirm the removal of corega DSLAAU software click lt Yes gt 3 You will be reminded not to unplug the USB cable until the uninstall
4. core products consists of 10 100 1000 Ethernet products Wireless Networking Products 802 11 a b g series broadband access routers and other networking peripheral such as IP camera and PoE Adapter Thank you again for purchasing corega DSLAAU USB ADSL Modem Wish you would enjoy the powerful and friendly corega connecting experience corega gt www corega com tw corega Taiwan Inc 7F No 10 Lane 345 YangGuang St Nei Hu Chiu Taipei City 114 Taiwan R O C TEL 886 2 8751 9164 FAX 886 2 8751 9174 PN T30 EM6101 00 Rev B
5. gt to reboot 12 Once the PC has rebooted installation of corega DSLAAU is complete DSLAAU Manual a Windows 98 WAN applications will ask you to provide telephone number and location information Enter the information and click lt Close gt b The Finished window will be displayed indicating the installa tion has been completed Click lt Finish gt 3 3 MAC OS 9 x Installation When installing corega DSLAAU on a Macintosh running OS 9 x you will need to install the drivers first and then plug the USB cable from your modem to the computer Installing the Driver Software 1 In the procedure that follows we shall refer to the folder where the driver files reside as the Device Driver Folder 2 In the Device Driver Folder locate the Installer application and invoke it by double clicking on it 3 The Welcome screen will appear Click lt Next gt to proceed 4 When all necessary files have been copied the Finished screen will appear giving you the opportunity to restart your computer Since you must restart your computer before using your modem select lt Restart now gt click inside the radio button to the left of it and click lt Finish gt DSLAAU Manual J ES ADSL Modem Installer Finished The installation is now complete Before using your modem you must restart your computer Would you like to restart now or later Restart now gt Restart later Finish gt C
6. has been detected USB ADSL Modem Please verify that it Is configured correctly then press Apply Now to activate it Router 192 168 11 254 DHCP Client ID Optional Ethernet Address 00 03 93 16 61 68 Example apple com earthlink net Click the lock to prevent further changes 3 From the Show pull down menu select the new port USB ADSL Modem ma Show All Displays Sound Network Startup Disk Built in Ethernet c m Internal Modem Show USB ADSL Modem D 3 f Active Network Ports Configure Using PPP a Domain Name Servers Optional AE IP Address Subnet Mask E Search Domains Optional Example apple com earthlink net Click the lock to prevent further changes DSLAAU Manual 4 Select the lt Modem gt tab In the Modem pull down menu select ADSL USB Modem Uncheck Wait for dial tone before dialing Check Show Modem Status in menu bar ee ja 409 Show All Displays Sound Network Si Location Automatic a Show USB ADSL Modem QO Modem ADSL USB Modem f a F Enable error correction and compression in modem Sound 0n Oof Dialing Tone 8 Wait for dial tone before dialing O Pulse 4 Show modem status in menu bar Click the tock to prevent further changes 5 Select the lt PPP gt tab Enter your username account name If you want to make your password permanently saved enter it and check Save
7. lt Yes gt remove the software from my computer and click lt Next gt DSLAAU Manual GOO ADSL Modem Installer j Uninstall This program will uninstall the DSL modem driver from your computer Are you sure you would like to continue a Yes remove the software from my computer No cancel the uninstallation Note You will need to enter in an administrator password to perform the uninstallation A x 4 ay f Cancel 3 Type the administrator name and password at the Authenticate screen and click lt OK gt 4 The Finish screen will appear The computer must be restarted to complete the uninstall process Select Restart now and click lt Finish gt OOO ADSL Modem Installer Finishe The installation is now complete Before using your modem you must restart your computer Would you like to restart now or later Restart now O Restart later AS f Finish Cancel SN ppendixA gt Modifying TCP IP Networking Options WAN USB Driver Microsoft Windows XP TCP IP settings are set up automatically during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Control Panel Double click the lt Network Connections gt icon 2 From the Network Connections window right click the lt Dial Up PPP Connection gt icon and click lt Propertie
8. password Configure any other PPP Options as desired ee Network o is 2440 B Show All Displays Sound Network Startup Disk Location Automatic a Show USB ADSL Modom a f TCPJiP PEP Proxies Y Proxies Madam Service Provider Optima Telephone Number Alternate Number Kpnenati Account Name gspr Password seseseee M save password Checking this box allows aP users of this computer 10 accesi this internet account withsul entering a password f PPP Options cac we lock 10 prevent further changes C opiy Now DSLAAU Manual 6 Select the lt TCP IP gt tab and select the way you would like to obtain your IP address The recommended way is Configure Using PPP Network gt MAO a Show Alt splays Sound Network Startup Desk Location Automatic al Show Ethernet Adaptor len2 al Frere Y PPPOE AppleTalk Proxies Configure Using PPP K Domain Name Servers Optional IP Address Provided by PPP server Subnet Mask Router Search Domains Optional Example apple com earthiiek net Ethernet Address 12 75 81 c6 00 af Click the lock to prevent further changes Apply Now 7 Click lt Apply Now gt Close the System Preferences application The installation and configuration is now complete Establishing a Connection 1 Open the Internet Connection ka which looks like a modem dialer by clicking the icon at the top right side of the screen and selecti
9. to quit the setup process to exit all Windows programs before continuing If the Windows programs were previously closed click Next gt Note If you quit this process run setup exe from the Device Driver Folder to resume the installation 7 The Select Service Provider window allows you to specify your DSL service provider A list of service providers is displayed Default values are provided for each DSL service provider listed in the window DSLAAU Manual 35 DSL Modem Setup Wizard lx Select Service Provider Choose your service provider from the list below and then click Next to continue Other Service Provider PPPoA WAN Connection PPPoE WAN Connection LAN Connection Customize lt Bwx EO cmd If your DSL service provider is listed and you would like to accept the default values highlight the provider s name and click Next gt Continue with Step 9 If your DSL service provider is listed and you would like to change the default values highlight the provider s name and click lt Cus tomize gt Continue with Step a If your DSL service provider is not listed select Other Service Provider and click Next gt Continue with Step a a Select the type of driver to be installed from the Select Driver Type window and click Next gt DSLAAU Manual En DSL Modem Setup Wizard Select Driver Type Selectthe type of driver that will be installed This choice depends on the servic
10. 992 2 G lite mode are likewise partitioned at 32kb s increments The downstream data rates extend from 64 kb s to 4 Mb s The upstream data rates extend from 32 kb s to 1024 kb s DSLAAU Manual Table 2 G 992 2 Payload Bit Rates Bit Rate kb s Power Requirements Typical Power Consumption Table 5 CP USB Modem Power Consumption CP USB Modem Power Consumption 5V Digital 0 100 W System Requirements Windows Operating Systems Windows 98 Windows 98SE Windows ME Windows 2000 or Windows XP 32 MB RAM e Pentium class processor 200MHz or better 1 Universal Serial Bus USB port 10 MB free HD space DSLAAU Manual MAC Operating System MAC OS 9 x OS X 10 1 x and above 10 0 is not supported Requires Macintosh USB driver version 1 2 or greater Supports iMac iBook G3 G4 PowerMac PowerBook G3 G4 Linux Operating System 32 MB RAM e Pentium class processor 200 MHz or better 1 Universal Serial Bus USB port 10 MB free HD space Hardware Requirements Processor Intel compatible 80486 or higher including Pentium and Pentium Pro URERA T T corega K K designs develops and markets professional networking products that address the specific needs of small and medium enterprises and home user s easy to use quality and reliable services of networking solutions requirements Established in 1986 corega 100 founded by Allied Tel esis Group in Yokohama Japan corega s
11. ADSL Modem Please verify that it is configured correctly then press Apply Now to activate it Router 192 168 11 254 DHCP Client ID Optional Example apple com earthlink net Ethernet Address 00 03 93 16 61 68 8 Click the tock to prevent further changes 3 From the Show pull down menu select the new port Ethernet Adapter en lt n gt DSLAAU Manual 1000 Network ia a Show A Display Sound Network Startup Disk Show Y Built in Ethernet internal Modem parak Y rs W Address 192 168 11 121 Provided by ONG Server Subnet Mask 255 255 255 0 Router 192 168 11 254 q A ONCE Client 10 Example saran Exhernet Address 00 03 93 16 61 68 Pa E cuca me tock to prevene further changes METIA 4 The next steps apply if you want to configure using PPPoE RFC 2516 5 Select the PPPoE tab and select Connect using PPPoE en a o w BAO Show A Displays Sound Network Startup Disk Location Automatic a Show Ethernet Adaptor len SSS gt J reer AppleTalk Proxies amp Connect using PPPOE T Save password this box allows all users of thes computer to Checking CASE OMS intarnet account without enering a pasiword E Show PPPOE status in menu bar caca the hock to prevent further changes L hooh Now 6 Select the TCP IP tab and select the way you would like to obtain your IP address The recommended way is Configure Using PPP DSLAAU Manua
12. DSLAAU USB ADSL Modem Soreaay Y User Manual Preface Y DSLAAU Manual 1 Overview 1 1 About ADSL iiscccicscecctscssonsasctessevsncedeversestssscbasscssesesadvatsceribeves 4 1 2 Protocol and Device Driver Selection m m m manasanasawnunaa 4 1 3 Features 2 Hardware Installation 2 1 Before YOU start cocococanococnnncnnnncnnncncnnononnocnonconon corn cnsonencnrrcnconens 7 Hardware InstallatiON c cconoorornononcnrnnncnrnononononos 7 3 Software Installation 3 1 Before YOU Start c ssscsssssssssccscscsssssecsssessssecsssecsssesasseeseeeesees 8 3 2 Windows Installation Installing the Driver Software 3 3 MAC OS 9 x Installation css 14 Installing the Driver Software 14 3 4 MAC OS X Installation 15 Installing the Driver Software oocomommmmmmm 15 4 Customizing Communication Settings 4 1 Accessing Communication Settings on Windows 17 4 2 Accessing Communication Settings on Mac 5 Updating Software 5 1 Windows Drivers Update sesssesssessessessssssssrossssssssssossese 5 2 MAC OS 9 x and OS X Drivers Update 6 Software Uninstall 6 1 Windows Uninstall cccoconononoconnrnnnoncncnnncnonoconononocncccnnnos 6 2 MAC OS 9 x Uninstall 6 3 MAC OS X Uninstall DN Contents Appendix A Modifying TCP IP Networking Options MAC OS 9 X cssesessessssssessessssessssesssessnssessssessseessseeeseees 32 MAC OS X Establishing a Conne
13. P IP 2 The TCP IP window will appear DSLAAU Manual 169 254 226 141 255 255 0 0 169 254 226 141 Make sure that Ethernet is selected in the Connect via drop down list The Configure drop down list should show Using DHCP Server 3 Close the TCP IP window You will be prompted to save the current configuration Click lt Save gt MACOSX If you have not done so yet connect corega DSLAAU to the computer using the proper USB device cable Connect the DSL line to corega DSLAAU too TCP IP settings are set up automatically during the software installa tion process The following procedure may be used to change TCP IP settings if necessary 1 Open System Preferences and select Network DSLAAU Manual MAG E Show All Displays Sound Network Startup Disk Personal dd Access Hardware e E y o a Colorsync Displays Energy Saver Keyboard Mouse Sound Internet amp Network jja 2 System Ba O 2 Classic Date Time Software Speech Startup Disk Users Update Other a e amp DAVE DAVE Login Network Sharing 2 A window should pop up indicating that a new port has been detected It will be a port of type Ethernet Adapter and its interface name en 2 will be displayed as well e g Ethernet Adapter en lt n gt Click lt OK gt Location Automatic a 3 New Port Detected A new network port has been detected USB
14. ancel k 3 4 MAC OS X Installation When installing corega DSLAAU on a Macintosh running OS X you will need to install the drivers first then plug the USB cable from your modem to the computer Note This device driver supports MAC OS X 10 1 x and above It does not support MAC OS X 10 0 Installing the Driver Software 1 In the procedure that follows we shall refer to the folder where the driver files reside as the Device Driver Folder 2 In the Device Driver Folder locate the Installer application and invoke it by double clicking on it 3 The Welcome screen will appear click lt Next gt to proceed 4 Enter the administrator login and password on the Authenticate screen and click lt OK gt 5 When all necessary files have been copied the Finished screen will DSLAAU Manual appear giving you the opportunity to restart your computer Since you must restart your computer before using your modem select lt Restart now gt click inside the radio button to the left of it and click lt Finish gt COO ADSL Modem Installer Finished The installation is now complete Before using your modem you must restart your computer Would you like to restart now or later Restart now Restart later Finish Cancel h The driver is now installed Before using your corega DSLAAU con nect the modem to the computer using the proper USB device cable and connect the DSL line t
15. ault gateway on remote network OK Cancel Change the IP address to a user defined address by selecting Specify an IP address click inside the radio button to the left of it and typing the address in the space provided Change the Name Server addresses to user defined addresses by selecting Specify name server addresses click inside the circle to the left of it and typing the addresses in the spaces provided Change the default gateway by leaving the box blank to the left of Use default gateway on remote network 5 Click lt OK gt to apply your changes and exit from the TCP IP Settings window 6 The Dial Up PPP Connection window will be redisplayed Click lt OK gt to end the TCP IP options modification session DSLAAU Manual MAC OS 9 x If you have not done so yet connect corega DSLAAU to the computer using the proper USB device cable Connect the DSL line to corega DSLAAU too TCP IP settings are set up automatically during the software installa tion process The following procedure may be used to change TCP IP settings if necessary 1 Click on the Apple icon 3 then select Control Panels gt Modem 2 Make sure that the ADSL USB Modem appears in the Modem drop down list You can modify the dialup settings such as dialing sound and type O Modem EE 8 Connect via Internal Modem Setup Modem ADSL USB Modem Sound Gon or Dialing Tone Pulse Ignore dial t
16. ction kaa INIA MAC OS OKni 47 MAC OS X Establishing a Connection Appendix B Point to Point Protocal over Ethernet PPPoE for WAN Applications PPPoE for LAN Applications Appendix C Specifications corega DSLAAU Connector Data Transfer RateS Power Requirements System Requirements e Hardware RequireMentS ococcnococoononsoninnocnonsononorcncncocononcnononso h Preface Y DSLAAU Manual This manual contains information regarding the installation opera tion and configuration of corega DSLAAU Additionally it outlines the use of the Control Panel Application The following chapters are included in this manual Chapter 1 Overview offers a brief description of ADSL protocol and device driver selection and the features of corega DSLAAU Chapter 2 Hardware Installation describes the steps for connecting corega DSLAAU Chapter 3 Software Installation describes the steps for installing corega DSLAAU drivers under various operating systems Chapter 4 Customizing Communication Settings provides detailed steps for altering the ATM Virtual Path ID VPI ATM Virtual Circuit ID VCI Encapsulation type and or Modulation type values previously defined Chapter 5 Updating Software details the procedure for updating to a new version of the modem software Chapter 6 Software Uninstall provides detailed steps for removing core
17. dvanced button of the Internet Protocol TCP IP Proper ties window may be used to alter DNS addresses WINS addresses and IP security settings 6 Click lt OK gt to apply your changes and exit from the Internet Protocol TCP IP Properties window 7 The Dial Up PPP Connection Properties window will reappear Click lt OK gt to end the TCP IP options modification session DSLAAU Manual Microsoft Windows 2000 TCP IP settings are set up automatically during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Settings gt Control Panel Double click the lt Network and Dial Up Connections gt icon 2 From the Network and Dial Up Connections window right click the lt Dial Up PPP Connection gt icon and click lt Properties gt 3 The General tab of the Dial Up PPP Connection Properties window allows you to specify a different VPI and VCI if needed Contact your DSL service provider before altering this connection information Enter the VPI and VCI in the Phone Number field For example 0 88 te Dial Up PPP Connection Properties General Options Security Networking Advanced Connect using E ISDN channel corega USB ADSL Modem Phone number Phone number 088 Attemates Use dialing rules Show icon in n
18. e of the windows and the wording of the options may be slightly different for each operating system but the same procedure applies Installing the Driver Software 1 In the procedure that follows we shall refer to the folder where the driver files reside as the Device Driver Folder 2 An informational message may be displayed If so click Next gt to start the installation 3 A window will appear asking what you want the system to do The recommended option will always search for the appropriate driver software Select the recommended option by clicking on the radio button to its left and click Next gt DSLAAU Manual 4 A window may be displayed which allows you to specify the location of the driver software to be installed If so point to the Device Driver Folder See Step 1 with no other options selected and click Next gt A message will indicate that the system is ready to install the device driver click Next gt a For Windows Me applications the Select Other Driver window may ask you to select the driver from a list of drivers If asked highlight the root directory identified with GROOTUSB INF in the Location column and click lt OK gt 5 For Windows 98 Windows 98 SE Windows Me applications a message will confirm that the device driver software has been installed click lt Finish gt 6 The Welcome window appears to start the next phase of the installation and provides an opportunity
19. e provider you are using L Driver A E b Enter Select the VPI VCI Encapsulation type and Modulation type from the Communication Settings window and click Next gt iL DSL Modem Setup Wizard x Communication Settings series Enter your communication settings below These settings are supplied by your service provider ver vc 88 Encapsulation arc 2364 PPPo amp TM NULL Encapsulation E Modulation Multimode lt Back Cancel DSLAAU Manual Note The encapsulation types that appear in the drop down list vary depending upon the type of driver selected in the previous step 9 The Ready to Install window will be displayed You may review the current settings and click lt Back to change the settings or click Next gt to accept the current settings 32 DSL Modem Setup Wizard Ready to Install Setup has enough information to start copying the driver files If you wantto review or change any settings click Back or Customize Ifyou are satisfied with the settings click Next to begin copying files 10 A message will be displayed indicating that the drivers are being installed Note You may need the Windows CD to complete the installation 11 The system must be rebooted to have the new settings take effect therefore the Reboot window will appear Remove all disks from their drives select lt Yes gt reboot the computer now and click lt Close
20. eeding with software installation IP Address Settings the software installation process allows the server to dynamically assign IP Address settings If your application requires static setting of specific address information you will need to know IP Address Subnet Mask for Bridged Ethernet applications only Default Gateway for Bridged Ethernet applications only Name Server Information the software installation process allows the server to dynamically assign Name Server Address settings Ifyour application requires static setting of specific address information you will need to know Primary DNS Address Secondary DNS Address Primary WINS Address Secondary WINS Address Type of Driver to be installed WAN and LAN software drivers are supported Note Required if not using default value DSLAAU Manual Encapsulation type Note Required if not using default value Modulation type Note Required if not using default value User Name for PPP applications only e Password for PPP applications only 3 2 Windows Installation The software setup process for Microsoft Windows applications XP 2000 Me 98 SE and 98 is described below with operating system specific differences noted corega DSLAAU should be connected to your PC prior to installing the driver software No other Windows programs should be running on your PC during the software install process Note The appearanc
21. end the modifying TCP IP options session DSLAAU Manual Microsoft Windows 98 and Windows 98 SE TCP IP settings are set up automatically during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Settings gt Control Panel Double click the lt Dial Up Networking gt icon 2 From the Dial Up Networking window right click on the lt Dial Up PPP Connection gt icon and click lt Properties gt 3 From the Server Types tab of the Dial Up PPP Connection window select TCP IP by checking the check to the left and click lt TCP IP Settings gt Dial Up PPP Connection fa Di General Server Types Scripting Mulhink Type of Dial Up Server Internet Wind Advanced options T Logon to network T Enable software compression T Require encrypted password TF Require data encryption T Record a log file for this connection Allowed network protocols TF NetBEUI I IPX SPX Compatible F ICPAP TCPAP Settings coca 4 Use the TCP IP Settings window to modify the IP address Name Server addresses and or default gateway as follows DSLAAU Manual TCP IP Settings 1 xj C Server assigned IP address Specify an IP address IP address 192 100 100 59 T Use IP header compression T Use def
22. etworks Install Uninstall Properties Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks T Show icon in taskbar when connected 4 Use the Internet Protocol TCP IP Properties window to modify the IP addresses and DNS Server addresses as follows Internet Protocol TCP IP Properties KIE General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings C Obtain an IP address automatically Use the following IP address IP address 192 100 100 59 Subnet mask 255 255 255 0 Default gateway 192 100 100 15 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server A F Altemate DNS server E E a DSLAAU Manual e Change the IP address to a user defined address by selecting Use the following IP address option click inside the circle to the left of it and typing the addresses in the spaces provided Change the DNS Server addresses to user defined addresses by selecting Use the following DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided The Advanced button of the Internet Protocol TCP IP Proper tie
23. ga DSLAAU software from the PC 1 1 About ADSL Asymmetric Digital Subscriber Line ADSL technology provides high speed data access across regular phone lines copper wires by making use of previously unused frequency bandwidth above the voice band By placing the ADSL signal above the frequency of the voice signal ADSL service is able to coexist on the same line with your telephone service ADSL is asymmetric in the sense that it pro vides a higher data rate in the downstream receive direction than in the upstream transmit direction Asymmetric operation is ideal for typical home and small office use where files and information are downloaded more frequently than uploaded corega DSLAAU is capable of supporting the following DSL stand ards ANSIT1 413 Issue 2 ITU G 992 1 G DMT ITU G 992 2 G lite and ITU G 992 Annexes A B and C as applicable 1 2 Protocol and Device Driver Selection corega DSLAAU can be easily connected to a USB port on the PC via a standard USB cable corega DSLAAU is fully software upgradeable so that new features and updates may be added by simply loading a new version of the device driver onto your PC two types of device drivers are provided for corega DSLAAU WAN and LAN The proper choice of driver depends on the combination of Windows operating system and protocol 1 WAN driver This driver causes the modem to resemble a dial up modem Call establishment is performed through Dial Up Netw
24. his manual when implementing PPPoE with the WAN driver PPPoE for LAN Applications PPPoE is supported via third party software when implemented with a LAN driver making the modem appear as a local area network LAN device to the operating system It allows multiple computer users on an Ethernet to share a common DSL connection to the Internet After installing the LAN driver follow the installation instructions DSLAAU Manual provided with the third party PPPoE software The third party soft ware will search for existing drivers If multiple drivers are installed select corega DSLAAU as the adapter of choice Internet connection will be made through the third party software You will be required to enter your User Name and Password WIN C Y DSLAAU Manual Specifications corega DSLAAU Connector corega DSLAAU is connected to your PC via a USB cable The rectan gular end of the USB cable inserts into the USB port of your PC while the square end of the cable inserts into the USB port of corega DS LAAU Data Transfer Rates ANSI T1 413 ITU G 992 1 Data Rates Data rates for DMT mode are partitioned at 32 kb s increments for both the upstream and downstream data rates adhering to the DMT Standards The downstream data rates extend from 32 kb s to 8 064 Mb s The upstream data rates extend from 32 kb s to 1024 kb s Table 1 ANSIT1 413 Payload Bit Rates Bit Rate kb s ITU G 992 2 Data Rates Data rates for G
25. idual needs TCP IP Properties Bindings Advanced NeBlos DNS Configuration Gateway wins Configuration IP Address The first gateway in the Installed Gateway list will be the default The address order in the list will be the order in which these machines are used New gateway L Installed gateways Hi Remove DSLAAU Manual To add a new gateway type the address in the New gateway field and click lt Add gt The new gateway will appear in the Installed gateways list To remove a previously installed gateway highlight the entry to be removed in the Installed gateways list and click lt Remove gt The gateway will no longer appear in the Installed gateways list 5 Click lt OK gt to apply your changes and exit from the TCP IP Properties window 6 The Network window will reappear Click lt OK gt to end the TCP IP options modification session 7 If you have made changes to TCP IP properties you will be asked to restart reboot your PC Click lt Yes gt and your PC will restart MAC OS 9 x If you have not done so yet connect corega DSLAAU to the computer using the proper USB device cable Connect the DSL line to corega DSLAAU too TCP IP settings are set up automatically during the software installa tion process The following procedure may be used to change TCP IP settings if necessary 1 Click on the Apple icon 3 and then select Control Panels gt TC
26. k box Enter any number in the Number field e You may wish to use the Options button to set up some ad ditional connection and protocol settings or accept the default Click lt OK gt when done with the Options window 9 Close the Remote Access window You will be prompted to save the current configuration Click lt Save gt DSLAAU Manual MAC OS X If you have not done so yet connect corega DSLAAU to the computer using the proper USB device cable Connect the DSL line to corega DSLAAU too TCP IP settings are set up automatically during the software installa tion process The following procedure may be used to change TCP IP settings if necessary 1 Open System Preferences and select Network ie maga Show All Displays Sound Network Startup Disk Personal Desktop General International Login ScreenSaver Universal Access Hardware 6G F 7 m B9 3 ColorSync Displays Energy Saver Keyboard Mouse Sound Internet amp Network o Internet QuickTime Sharing System taO el AL Classic Date amp Time Software Speech Startup Disk Users Update Other a Y DAVE DAVE DAVE Login Network Sharing 2 A window should pop up indicating that a new port has been detected It will be named corega DSLAAU Click lt OK gt DSLAAU Manual re Show Alt Displays Sound Network Sta Location _ Automatic Show New Port Detected A new network port
27. l C00 Network a BASO Network Startup Disk Location Automatic a Show Ethernet Adaptor en2 a Frcene Y error AppleTalk Proxies Configure Using PPP re Domain Name Servers Opcional IP Address Provided by PPP server Subnet Mask Router Search Domains Optional Example apple com earthlink net Ethernet Address 12 75 81 06 00 af 8 Click the tock to prevent further changes E Apply Now 7 If indicated by your ISP enter any proxies needed at the Proxies tab 8 Click lt Apply Now gt to apply the changes Close the System Preferences application The installation and configuration is now complete Establishing a Connection 1 Open the Internet Connection aaron which looks like a modem dialer by clicking the icon at the top right side of the screen and selecting Open Internet Connection from the menu gt KO PPPoE Connected Disconnect Y Ethernet Adaptor en2 Open Internet Connect 2 In the Configuration drop down menu select your adapter s port Ethernet Adapter en 2 and fill in the password if it was not DSLAAU Manual provided in Step 5 above click lt Connect gt ea Ethernet Adaptor en2 Configuration Ethernet Adaptor en2 mm A Service Provider Name gspn Password A Show PPPoE status in menu bar These settings can be changed in Network Preferences Cra 3 The Internet Connection application will display the progress of
28. ll no longer appear in the Installed gateways list 5 Click lt OK gt to apply your changes and exit from the TCP IP Properties window 6 The Network window will reappear Click lt OK gt to end the TCP IP options modification session 7 If you have made changes to TCP IP properties you will be asked to restart reboot your PC Click lt Yes gt and your PC will restart DSLAAU Manual Microsoft Windows 98 and Windows 98 SE TCP IP settings are set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Settings gt Control Panel Double click the lt Network gt icon Highlight TCP IP gt corega DSLAAU from the list of installed network components in the Configuration tab of the Network window click lt Properties gt From the IP Address tab of the TCP IP Properties window select either the Obtain an IP address Automatically or Specify an IP Address option depending on your network setup If you select Specify an IP address type the IP Address and Subnet Mask in the spaces provided Consult with your network administrator to determine which option best suits your individual needs The Gateway tab allows you to add or remove gateways Consult with your network administrator to determine the appropriate addresses for your indiv
29. ng Open Internet Connection from the menu 2 In the Configuration drop down menu select your adapter s port USB ADSL Modem and fill in the password if it was not provided in Step 5 above and click lt Connect gt DSLAAU Manual e00 USB ADSL Modem Configuration USB ADSL Modem BEZ Service Provider Telephone Number 1 Mm Alternate Number Name gspn Password COTTI wv Show modem status in menu bar These settings can be changed in Network Preferences Status idle 3 The Internet Connection application will display the progress of the connection Upon completion you will be connected to the Internet The Disconnect button may be used to remove the connection effectively disconnecting from the Internet LAN USB Driver Microsoft Windows XP TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Control Panel Double click the lt Network Connections gt icon 2 Double click the lt Local Area Connection gt icon from the Network Connections window 3 Select Internet Protocol TCP IP from the General tab of the Local Area Connection Properties window Click lt Properties gt DSLAAU Manual ocal Area Connection Properties General Authentication Advanced Connect
30. ngs gt Dial Up PPP Connection ajx General Networking Security Scripting Multilink Dialing Type of Dial Up Server Per Internet Windows 2000 NT Windows ME X r Advanced options F Enable software compression J Record a log file for this connection r Allowed network protocols FT NetBEUI I IPX SPX Compatible M ICPAP TCP IP Settings DSLAAU Manual 4 Use the TCP IP Settings window to modify the IP address Name Server addresses and or default gateway as follows C Server assigned IP address Specify an IP address PE Pees 192 100 100 59 C Specify name server addresses 0 O O AO lag O AA O A EON O TF Use IP header compression T Use default gateway on remote network par E Change the IP address to a user defined address by selecting Specify an IP address click inside the circle to the left of it and typing the address in the space provided Change the Name Server addresses to user defined addresses by selecting Specify name server addresses click inside the circle to the left of it and typing the addresses in the spaces provided Change the default gateway by leaving the box blank to the left of Use default gateway on remote network 5 Click lt OK gt to apply your changes and exit from the TCP IP Settings window 6 The Dial Up PPP Connection window will be redisplayed Click lt OK gt to
31. o corega DSLAAU To configuration corega DSLAAU consult Appendix A Modifying TCP IP Networking Options Instructions for the WAN driver and In structions for the LAN driver RFC 1483 Customizing Commnuication Setting DSLAAU Manual 4 1 Accessing Communication Settings on Windows Once corega DSLAAU and software have been installed the commu nication settings may be easily updated by performing the following steps 1 From your PC desktop click Start gt Programs gt Corega USB ADSL Modem gt Configure 2 The Communication Settings window will be displayed 32 DSL Modem Setup Wizard x Communication Settings Enter your communication settings below These settings are supplied by your service provider VPI fe Vel fee Encapsulation rec 2364 PPPoATM NULL Encapsulation Modulation Multimode CE ts Make the necessary changes to the VPI VCI Encapsulation type and or Modulation type and click Next gt 3 The system must be rebooted to have the new settings take effect therefore the Reboot window will appear Remove all disks from their drives select lt Yes gt reboot the computer now and click lt Close gt to reboot 4 2 Accessing Communication Settings on Mac Access to corega DSLAAU s Communication Settings is not provided on the MAC OS Updating Software 5 1 Windows Drivers Update Once corega DSLAAU has been installed updating to a new version
32. one 3 Close the Modem window click on the top left corner You will be prompted to save the current configuration Click lt Save gt 4 Next click again on the Apple icon and then select Control Panels gt TCP IP 5 The TCP IP window will appear DSLAAU Manual Connect via Setup Configure Using PPP Server IP Address will be supplied by server gt Subnet mask lt will be supplied by server gt Router address will be supplied by server gt Search domains Name server addr Make sure that PPP is selected in the Connect via drop down list The Configure drop down list should show Using DHCP Server 6 Close the TCP IP window You will be prompted to save the current configuration Click lt Save gt 7 Click on the Apple icon and then select Control Panels gt Remote Access 8 The Remote Access window lets you set up the remote login parameters DSLAAU Manual O Remote Access N Setup Registered User Q Guest Mame username Save password Status Idle Note If you do not see the Name and Password fields click on the small triangle to the left of the word Setup Enter your userid in the Name field Type in your password in the Password field Choose whether or not to have your password saved by checking or unchecking the Save Password chec
33. orking This driver supports RFC 2364 and 2516 with PVC connections It can be used with Windows 98 Windows 98 SE DSLAAU Manual Windows 2000 Windows Me and Windows XP MAC OS 9 x RFC 2364 only MAC OS X 10 1 x and above RFC 2364 only as well as Linux 2 LAN driver This driver makes the modem appear as a LAN or Ethernet device Connection establishment is automatic This driver supports RFC 1483 with PVC connections Additionally PPPoE is supported via third party software This driver can be used with Windows 98 Windows 98 SE Windows 2000 Windows Me and Windows XP MAC OS 9 x MAC OS X 10 1 x and above as well as Linux The device driver choices are summarized in the table below Driver Type Operating System RFC 2364 Windows 2000 RFC 2516 not with Windows XP MAC OS 9 x nor Windows Me with MAC OS X Windows 98 SE Windows 98 MAC OS 9 x MAC OS X 10 1 x and above RFC 1483 Windows 2000 RFC 2516 MACOS Windows XP X 10 1 x and above Windows Me only Windows 98 SE Windows 98 MAC OS 9 x MAC OS X 10 1 x and above DSLAAU Manual 1 3 Features corega DSLAAU provides the following features Compliant with Universal Serial Bus Specification Revision 1 1 USB bus powered an external power supply is not required Supports two device drivers Microsoft NDIS 4 0 WAN Miniport and NDIS 4 0 LAN Miniport Compatible with T1 413 i2 G DMT and G lite compliant CO DSLAM equipment Software upgradeable
34. otification area when connected 4 From the Networking tab of the Dial Up PPP Connection Properties window select lt Internet Protocol TCP IP gt and click lt Properties gt DSLAAU Manual 5 Use the Internet Protocol TCP IP Properties window to modify Dial Up PPP Connection Properties 1 Aux General Options Security Networking Sharing Type of dial up server am calling Settings Components checked are used by this connection Y Y Internet Prote M8 File and Printer Sharing for Microsoft Networks M 3 Client for Microsoft Networks Install Uninstall Properties Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 0k Ced the IP address and DNS Server addresses as follows Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 2 Use the following IP address IP address 192 100 100 59 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server DSLAAU Manual e Change the IP address to a user defined addre
35. owing DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided The Advanced button of the Internet Protocol TCP IP Proper ties window may be used to alter IP settings DNS server ad dresses WINS addresses IP security options and TCP IP filtering options Click lt OK gt to apply your changes and exit from the Internet Protocol TCP IP Properties window 6 The Local Area Connection Properties window will reappear Click lt OK gt to end the TCP IP options modification session Microsoft Windows 2000 TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Settings gt Control Panel Double click the lt Network and Dial Up Connections gt icon Double click the lt Local Area Connection gt icon from the Network and Dial Up Connections window Select Internet Protocol TCP IP from the General tab of the Local Area Connection Properties window Click lt Properties gt DSLAAU Manual Local Area Connection 2 Properties 2 x General Sharing Connect using BD corega USE ADSL LAN Modem Configure Components checked are used by this connection M 3 Client for Microsoft Networks yw Bile and Printer Sharing for Microsoft N
36. process has been completed Click lt OK gt 4 Amessage will be displayed indicating the software is being removed 5 You will be prompted to unplug your modem Unplug the USB cable from the PC and click lt OK gt 6 The Reboot window will appear Remove all disks from their drives select lt Yes gt reboot the computer now and click lt Close gt to reboot Note The USB cable must be unplugged before the system is rebooted 6 2 MAC OS 9 x Uninstall 1 Invoke the Uninstaller from corega DSLAAU folder Applications gt Corega USB ADSL Modem gt Uninstall 2 The Uninstall screen will appear Select lt Yes gt remove the software from my computer and click lt Next gt 3 The Removing Software screen will indicate that files are being removed DSLAAU Manual do so Unplug the cable and click lt OK gt 5 The Finish screen will appear The computer must be restarted to complete the uninstall process Select lt Restart now gt and click lt Finish gt EE ADSL Modem Installer Finished The installation is now complete Before using your modem you must restart your computer Would you like to restart now or later Restart now O Restart later Finish 3 Cancel gt 6 3 MAC OS X Uninstall 1 Invoke the Uninstaller from corega DSLAAU folder Go gt Applications gt Corega USB ADSL Modem gt Uninstall 2 The Uninstall screen will appear Select
37. s window may be used to alter IP settings DNS server ad dresses WINS addresses IP security options and TCP IP filtering options 5 Click lt OK gt to apply your changes and exit from the Internet Protocol TCP IP Properties window 6 The Local Area Connection Properties window will reappear Click lt OK gt to end the TCP IP options modification session Microsoft Windows Me TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Control Panel window Start gt Settings gt Control Panel Double click on the Network icon 2 Select TCP IP gt USB ADSL LAN Modem from the Configuration tab of the Network window Click lt Properties gt DSLAAU Manual Configuration dertiicaton Access Conta The following network components are inataled DisUp Adaptor USB ADSL LAN Modem TCPAP gt 3Com Etherlink 10100 PO For Complete PC TCPAP gt Diatlip Adapter Pamay Network Logon Chen tee Miercacit Netwerks File and Print Sharing Deserigtion TEPAP ts the protocol you i lo corel to the beber and mide sreo networks Cor _ Coca 3 From the IP Address tab of the TCP IP Properties window select either the Obtain an IP address Automatically or Specify an IP Address option depending on your network setup If yo
38. s gt Network Connections File Edit View Favorites Tools Advanced Help O a O a pO search E Folders E Address Network Connections Network Tasks E Create a new connection 9 Set up a home or small office network Start this connection LAN or High S Set as Default Connection Rename this connection a i 1 acd Create Copy J Delete this connection Dl 2 Change settings of this Ca ol Delete connection Rename Properties Other Places Gp Control Panel 3 The General tab of the Dial Up PPP Connection Properties window allows you to specify a different VPI and VCI if needed Contact your DSL service provider before altering this connection information Enter the VPI and VCI in the Phone Number field For example 0 88 te Dial Up PPP Connection Properties General Options Security Networking Advanced Connect using BISON channel corega USB ADSL Modem Phone number Area code Phone number 0 88 Alternates Use dialing rules Dialing Rule Show icon in notification area when connected DSLAAU Manual 4 From the Networking tab of the Dial Up PPP Connection Properties window select Internet Protocol TCP IP and click lt Properties gt gt Dial Up PPP Con nection Properties Genetal Options Secuity Networking Advanced Type of dial up server am caling
39. ss by selecting Use the following IP address click inside the circle to the left of it and typing the address in the space provided Change the DNS Server addresses to user defined addresses by selecting Use the following DNS server addresses click inside the circle to the left of it and typing the addresses in the spaces provided The Advanced button of the Internet Protocol TCP IP Proper ties window may be used to alter DNS addresses WINS addresses and IP security settings 6 Click lt OK gt to apply your changes and exit from the Internet Protocol TCP IP Properties window 7 The Dial Up PPP Connection Properties window will reappear Click lt OK gt to end the modifying TCP IP options session Microsoft Windows Me TCP IP settings are automatically set up during the software installation process The following procedure may be used to change TCP IP settings if necessary 1 From your PC desktop open the Dial Up Networking window Start gt Settings gt Dial Up Networking 2 From the Dial Up Networking window right click on the lt Dial Up PPP Connection gt icon and click lt Properties gt DSLAAU Manual Ew Ed Yew Favomer ooh Corecom Hep Peke o O Aseh Sri IAE KE Opara te prc sheet solid a 3 From the Networking tab of the Dial Up PPP Connection window select TCP IP marked with a check in the check box to the left and click lt TCP IP Setti
40. the connection Upon completion you will be connected to the Internet The Disconnect button may be used to remove the connection effectively disconnecting from the Internet Configuration f Ethernet Adaptor en2 al fa Service Provider Name gspn Password V Show PPPoE status in menu bar These settings can be changed in Network Preferences tar Status Connected To 192 100 100 25 Send Receive Connect Time 00 00 15 IP Address 192 100 100 115 AppendixB 4 B fA DSLAAU Manual Point to Point Protocal over Ethernet PPPoE Point to Point Protocol over Ethernet is a specification for connecting multiple computer users on an Ethernet to a remote site through common customer premises equipment PPPoE can be used to have an office or building full of users share a common DSL Digital Subscriber Line connection to the Internet PPPoE combines the Point to Point Protocol commonly used in dialup connections with the Ethernet protocol which supports multiple users in a local area network The PPP Protocol information is encapsulated within an Ethernet frame corega DSLAAU supports PPPoE for WAN and LAN applications as presented in this section PPPoE for WAN Applications PPPoE support is embedded into the WAN driver making the mo dem appear as a dial up modem to the operating system Dial Up Networking is used to establish a connection Follow the installation instructions provided in t
41. u select Specify an IP address type the IP Address and Subnet Mask in the spaces provided Consult with your network administrator to determine which option best suits your individual needs TCP IP Properties xi Bindings Advanced NeBlos DNS Configuration Gateway WINS Configuration IP Address An IP address can be automatically assigned to this computer IF your network does not automatically assign IP addresses ask your network administrator for an address and then type it in the space below 9 Specify an IP address IP Addiess Subnet Mask Detect connection to network media DSLAAU Manual 4 The Gateway tab allows you to add or remove gateways Consult with your network administrator to determine the appropriate addresses for your individual needs TCP IP Properties BE Bindings Advanced NeBios DNS Configuration Gateway wins Configuration IP Address The first gateway in the Installed Gateway list will be the default The address order in the list will be the order in which these machines are used New gateway Installed gateways 192 100 100 15 Remove To add a new gateway type the address in the New gateway field and click lt Add gt The new gateway will appear in the Installed gateways list To remove a previously installed gateway highlight the entry to be removed in the Installed gateways list and click lt Remove gt The gateway wi
42. using 89 corega USB ADSL LAN Modem 27 This connection uses the following items 87 8 Cient for Microsoft Networks File and Printer Sharing for Microsoft Networks M 8 005 Packet Scheduler i Internet Protocol TCP Description Transmission Control ProtocolAntemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected 4 The Internet Protocol TCP IP Properties window is used to modify the IP addresses and DNS Server addresses as follows Internet Protocol Ti Prope a 2 x General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 100 100 59 Subnet mask 255 255 255 0 Default gateway 192 100 100 15 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server A Alternate DNS server E p DSLAAU Manual Change the IP address to a user defined address by selecting Use the following IP address option click inside the circle to the left of it and typing the addresses in the spaces provided Change the DNS Server addresses to user defined addresses by selecting Use the foll
Download Pdf Manuals
Related Search