Cooper Lighting INVUE IMI-572 User's Manual
Contents
1. INVUE INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE General Upon receipt of fixture thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier Compare the catalog description listed on the packing slip with the fixture label on the housing to assure you have received the correct merchandise Ascent Strut Fixtures Sheet 1 of 5 Safety This fixture must be wired in accordance with the national electrical code and applicable local codes and ordinance Proper grounding is required to insure personal safety Carefully observe grounding procedure All work should be done by an electrician WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker panel or fuse box before installing or servicing WARNING Risk of Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 1 Open door by depressing LATCH BUTTONS into door and lifting Fig 1 BUTTONS 2 Remove DOOR while it is at a 20 30 angle to the housing This will allow the door to slide over and forward from the hinges Fig 2 3 Disconnect PRIMARY QUICK DISCONNECT by grabbing sides and pulling away from fixture Fig 3 PRIMARY QUICK DISCONNECT NOTE Fusing and the cube starter are accessible from the bottom exposed side of the POWER TRAY They may be ser2. LATE fixture until WALL BRACKET fits over WALL PLATE Tighten to support fixture as shown Fig 7 1 4 20 SOCKET SCREW Fig 8 Make wire connections in WALL BRACKET Wire the fixture ground lead to the supply ground lead Wire the fixture voltage lead to the supply voltage lead Fig 8 Wire the fixture common lead to the supply common lead NOTE To wire to circuits not having a neutral lead such as 480V connect the fixture voltage lead to one of the supply leads and the fixture common lead to the other supply lead WALL BRACKET NOTE Ensure wires are not pinched while closing WALL BRACKET to WALL PLATE r L bT eee BRACKET SUPPORT HOLES These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 572 AVU040062 INY UE Ascent Strut Fixtures INSTALLATION INSTRUCTIONS Settore 4 26 04 IMI 572 IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing WARNING Risk of
3. Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 9 To reinstall POWER TRAY hang POWER TRAY from POWER REFLECTOR Rotation Removal TRAY HINGE swing POWER TRAY up till POWER TRAY 10 Open DOOR by depressing LATCH BUTTONS into door LATCH snaps closed Reconnect PRIMARY QUICK Reference Fig 1 DISCONNECT Install lamp Reinstall DOOR at 20 30 angle to housing ensuring both hinges are engaged Close DOOR ensuring DOOR LATCHES are completely engaged Listen 11 To lower REFLECTOR press the two REFLECTOR TABS for both cams to click on each latch Fig 9 outward and swing the REFLECTOR down Fig 11a amp 11b The REFLECTOR may now be lifted off of its hinges for rotation or removal REFLECTOR NOTE Prior to installing the lamp check to make sure lamp is of proper type and wattage Observe lamp manufacturer s recommendations and restrictions regarding lamp operation NOTE Reflector are marked to insure reflector is installed in proper orientation regarding Street Side If other orientation is desired reflector may be rotated 90 in either direction REFLECTOR TABS REFLECTOR These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or mai
4. When maintenance is performed check torque on all fasteners and tighten to specified torque if required CLEANING The reflector and door glass may be cleaned with any suitable non abrasive glass cleaning solution soap or detergent and rinsed with clean water Please remove the reflector and door from the fixture prior to cleaning KEEP THIS DOCUMENT FOR FUTURE REFERENCE These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 572 AVU040062
5. ardware are shipped separately from the fixture 6 Assemble WALL BRACKET to SPACER and HOUSING with 2 BOLTS 2 FLAT WASHERS and 2 LOCK WASHERS by feeding BOLTS through holes in SPACER and into tapped holes in WALL BRACKET Fig 6A amp 6B Torque BOLTS as follows e 2 1 2 13 AEM 450 in lbs OR e 2 5 16 18 AES 130 in lbs A WARNING surPont Risk of Personal Injury Fixture may become damaged and or WALL unstable if not installed properly BRACKET Tighten all fixture components to their recommended torque values These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 ImI 572 AVU040062 INU LE Ascent Strut Fixtures INSTALLATION INSTRUCTIONS e t ors IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE nese acta RETAIN FOR FUTURE REFERENCE A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing 7 Hook WALL BRACKET over WALL PLATE and place 8 Push SUPPORT BRACKET into WALL BRACKET and lower SUPPORT BRACKET into SUPPORT HOLES in WALL P
6. ntenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 572 AVU040062 INVUJE INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE Ascent Strut Fixtures Sheet 5 of 5 A WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing WARNING Risk of Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 12 To remove the REFLECTOR disconnect the REFLECTOR CONNECTOR from the HOUSING Fig 12 REFLECTOR CONNECTOR 13 To reinstall reverse steps 12 and 11 listening for audible clicks as REFLECTOR TABS engage REFLECTOR NOTE This fixture is to be installed as a DOWNLIGHT ONLY This fixture is not suitable for UPLIGHT mounting configurations NEMA TWIST LOCK PHOTOCONTROL amp RECEPTACLE The photocontrol receptacle is factory installed and ordered with the fixture The photocontrol is ordered separately and must be field installed The voltage of the photocontrol must match the voltage of the fixture FUSING Single fuse is available for use with 120V 277V or 347V fixture Double fuse is available for use with 208V 240V or 480V fixtures MAINTENANCE
7. viced without opening the POWER TRAY Hold POWER TRAY HANDLE and press POWER TRAY LATCH away from the power tray Hinge power tray up and lift from fixture Fig 4 HANDLE These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting Customer First Center 1121 Hwy 74 South Peachtree City GA 30269 IMI 572 avuo4o062 INY UE Ascent Strut Fixtures INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing WARNING Risk of Personal Injury Fixture may become damaged and or unstable if not installed properly Tighten all fixture components to their recommended torque values 5 Using WALL PLATE as a template drill 4 holes in wall Install appropriate wall anchors not supplied and secure GASKET and WALL PLATE to wall with 4 1 2 13 X 1 12 long BOLTS y BAD Fig 6A and 4 Lockwashers Fig 5 Torque BOLTS to 450 in lbs A HOUSING SPACER WALL WASHERS BRACKET FLAT WASHERS NOTE The SPACER WALL BRACKET and associated components and h
Download Pdf Manuals
Related Search