Coleman 100-RANG User's Manual
Contents
1. 54 PREPARING FOR OPERATION 1 Check the heater for possible shipping damage If any is found immediately notify your dealer 2 Follow all of the Safety Precautions 3 Install plumbing to a low pressure 1 2 psig maximum source of natural gas using a minimum 3 4 i d hose or flexible connector not over 10 feet in length 4 Connect the hose to the heater at the 1 2 SAE flare fitting at the inlet 5 Securely tighten all gas connections 6 Open the gas cock and check all gas connections with a START 1 Fully open the gas cock at the natural gas source 2 Place control knob of the safety pilot valve in pilot position and depress the knob admitting gas to pilot Push and release the piezo button until the pilot lights multiple tries may be necessary Alternately place a lighted match near the pilot pilot is above cutout in the middle pan If hose is filled with air allow a few minutes for gas to reach the pilot 3 When the pilot lights continue to hold the button on the Safety pilot valve depressed for 30 seconds then release 4 lf the pilot goes out wait 5 minutes and repeat the start procedure 5 When the pilot remains lit turn the knob left 1 4 turn to the ON position and the main burner will light CAUTION INADEQUATE FUEL SUPPLY or lowering burn rate can cause sooting STOP 1 Securely close the gas cock at the gas source 2 Depress the control knob of the pilot valve and turn clockwise to OFF position RESTART AFTERS2. Assembly 1 6505 Fitting Male Connector 1 14 3683 Floor Shield Assembly 1 7161 Nut Piezo 1 15 1098 Emitter Grill 1 3451 Electrode 1 A hazardous condition may result if a heater is used that has been modified or is not functioning properly When the heater is working properly The flame is contained within the heater The flame is essentially blue with perhaps some yellow tipping There is no strong disagreeable odor eye burning or other physical discomfort There is no smoke or soot internal or external to the heater There are no unplanned or unexplained shutdowns of the heater The parts list shows the heater as it was constructed Do not use a heater which is different from that shown A heater which is not working right must be repaired but only by a trained experienced service person Contact the factory for the service center closest to you phone number 909 981 5343 You may also obtain in warranty or out of warranty service by returning the product freight prepaid to Scheu Products Company 8855 Baker Ave Rancho Cucamonga CA 91730 INSTRUCTIONS FOR ORDERING PARTS All parts orders must show Heater Model No Item No Part No and Description We recommend that only parts Supplied by the manufacturer be used on this unit A locally purchased part may appear to be identical although in reality it might endanger the heater or the persons Operating the heater The heater should be serviced only
3. AFETY SHUTDOWN 1 Securely close gas cock at the gas source 2 Wait 5 minutes 3 Restart following Start procedure ANSI Z83 7b 1993 CGA 2 14 1972 Construction Heater SCHEU PRODUCTS COMPANY INC P O BOX 5050 UPLAND CA 91785 5050 MODEL 100 RANG SPC 100RANG Na ey er 2 Vj tp ify m i N AS l Yj A MHI i A WN AN fi NU f Sy Ls f FIPE OF GAS oronro Natural Gas INPUT RATING nnn 100 000 BTU hr MANIFOLDPRESSURE 4 Water Column 14 MAX GAS SUPPLY PRESSURE 1 2 psi MIN GAS SUPPLY PRESSURE 5 W C PARTSLIST Part Part Item No Description Qty Item No Description Qty 1 0814 Base Assembly 1 16 3101 Louvered Emitter 1 2 3095 Ballast 1 17 3102 Pan Hood 1 3 1074 Valve Shield Assembly 1 18 6500 Fitting 1 2 x Close Nipple 1 4 6113 Orifice 55 Drill 1 19 6259 Regulator 4 W C 1 5 1510 Pilot Assembly 1 20 6125 Fitting Male Connector 1 6 1072 Manifold Assembly 1 21 7253 Orifice Pilot 1 7 7616 Thermoelectric Valve 1 22 6384 Label Natural Gas Only 1 8 6067 Spacer 5 16 id x 1 2 5 4222 Bracket Piezo 1 9 1837 Pilot Tube Assembly 1 24 7291 Label Model Operating Instructions 1 10 6137 Fitting Female Elbow 1 6473 Ignitor Piezo 1 11 6234 Thermocouple 16 1 26 3106 Leg Base Side 2 7290 Manual Operating Instructions 1 27 3105 Leg Base Front 1 13 1594 Bracket Pilot Mounting
4. SCHEU PRODUCTS COMPANY INCORPORATED Mail P O Box 250 Upland CA 91785 Plant 8855 Baker Ave Rancho Cucamonga CA 91730 Telephone 909 981 5343 ASSEMBLY ANDOPERATINGINSTRUCTIONS MODELS 100 RANG SPC 100RANG CONSTRUCTIONHEATER YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS SO PLEASE READTHESE INSTRUCTIONS BEFORE YOU OPERATE THIS HEATER A GENERAL HAZARDWARNING FAILURE TO COMPLY WITH THE PRECAUTIONS ANDINSTRUCTIONS PROVIDED WITH THIS HEATER CANRESULT IN DEATH SERIOUS BODILY INJ URY ANDPROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE EXPLOSION BURN ASPHYXIATION AND CARBON MONOXIDE POISONING ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER IF YOUNEEDASSISTANCE OR HEATER INFORMATION SUCHAS ANINSTRUCTIONS MANUAL LABELS ETC CONTACT THE MANUFACTURER A WARNING FIRE BURN INHALATION AND EXPLOSION HAZARD KEEP SOLID COMBUSTIBLES SUCH AS BUILDING MATERIALS PAPER OR CARDBOARD A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS NEVER USE THE HEATERINSPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES OR PRODUCTS SUCHAS GASOLINE SOLVENTS PAINT THINNER DUST PARTICLES OR UNKNOWN CHEMICALS OPERATINGINFORMATION Intended use is primarily the temporary heating of buildings under construction alteration or repair A WARNING NOT FOR HOME OR RECREATIONAL VEHICLE USE SAFETY PRECAUTIONS 1 Check the heat
5. by a trained experienced service person Read the section on Servicing before ordering parts For parts order call 909 981 5343 SEPTEMBER 1999 P N 7290L
6. er thoroughly for damage DO NOT operate a damaged heater 2 DO NOT modify the heater or operate a heater which has been modified from its original condition 3 Provide atleast 5 W C but not over 1 2 psig to the heater inlet 4 Use an appropriate hose or flexible connector not over 10 ft in length 5 Operate the heater only with the 4 W C regulator provided by the factory 6 For indoor use only Area must be well ventilated Provide minimum openings of 2 sq ft near the floor and 2 sq ft near the ceiling 7 lf at any time gas odor is detected IMMEDIATELY DISCONTINUE operation until the source of gas has been located and corrected 8 Install the heater such that it is not directly exposed to water spray rain and or dripping water or wind 9 Maintain minimum clearance from normal combustible materials of 6 feet in all directions Locate 10 ft from canvas tarpaulins or similar coverings and secure them to prevent flapping or movement due to wind action 10 Operate only on a stable level surface 11 Since permanent skin tissue damage can occur avoid contact with the unit while is is operating or shortly after it has been shut off 12 Do not use on combustible floors 13 Do not move handle or service while hot or burning 14 Use only in accordance with local codes 15 Installation of this natural gas heater must conform with local codes or in the absence of local codes with the National Fuel gas Code ANSI Z223 1NFPA
Download Pdf Manuals
Related Search