Clarion S100 User's Manual
Contents
1. If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed Doors are covered by system differently if the alarm is triggered by an open door for three full cycles the doors will be bypassed until the trigger ceases note Arming and disarming the system does not reset this func tion The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition If testing your system it is important to remember that the false alarm pre vention circuitry programming can cause zones fo be bypassed and appear to stop working If five chirps are heard when disarming false alarm prevention circuitry has been engaged If you wish to clear the false alarm prevention cir cuitry memory turn the ignition key on See Programming Options section of this guide for false alarm circuitry programming 13 diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from dis abling the entire system The microprocessor will also record and report any triggers that occurred during your absence Refer to the System Status Chirps and Table of Zones charts for diagnostic information arming diagnostics If t2. AED arming cycle Thirty seconds later the starter of the vehicle will be disabled To start the car it will be necessary to disarm the system with the remote It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Override switch the programmed number of times AED is disabled when the system is in valet mode 21 22 note This feature will only function if the Starter Kill relay has been installed Full trigger response 30 or 60 seconds This determines how long the full triggered sequence lasts Some states have laws regulating how long a security system can sound before it is considered a nuisance If your installer is programming the security system with the Pro Security Programmer the full triggered response can be programmed for any duration ranging from 1 to 180 seconds False alarm prevention Circuitry on or off Please refer to the false alarm prevention circuitry section of this manual for a further explanation If the false alarm prevention circuitry is programmed off the security system will respond to inputs from any sensor indefinitely note Because many states have laws regulating security sys tems programming false alarm prevention circuitry off may cause your system fo violate state laws Progressive door trigger on or off When the system is armed and a door is opened the system responds with ten chirps prior to beginning the full trig
3. and 4 are now bypassed Press a fifth time within five seconds The siren chirps five times followed by a long chirp All input zones except the ignition are now bypassed Continued pressing of will begin the Remote Sensor Bypass cycle over again note Remote Sensor Bypass only applies to a single arming cycle Once the system is disarmed and then re armed all the zones will be active again arming while driving Your system can be armed while driving the vehicle Simply press E on J your remote for two seconds while the vehicle is running or while the igni tion is on The siren will chirp once and then once more to indicate that the ignition is on The security system will not respond to any input except the door triggers and the Starter Kill if installed will not be activated The security system will disarm automatically whenever the ignition is turned off The siren will chirp twice and the LED will stop flashing note If programmed for the optional AntiCar Jacking fea ture arming with the remote will arm this feature See Anti Car Jacking section of this guide disarming To disarm the system press d You will hear two chirps and the parking lights will flash twice If the power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming refer to the Diagnostics section of this guide to deter m
4. eee e eee cece eee 2 Whatiis included xiii a dle 3 important information oooocoocococo eee eee ees 3 system maintenance 2 2 06 da mea heal tian Son ol a as 4 TECHO NOICE uti cota ba ew eink ae ove a we tee Bale 4 remote functions 0 eect eee teens 4 USING your SYStEM ooo 6 ACTIVE LALMING ns css ot a Peet Ge oia o Rows adi ada 6 DaSSIVELarMING a Rasa a eRe i PA RS de Ae eS 6 remote sensor bypass 2 2 2 ett eee 8 arming while Griving 2 4 tetera a wae eh ee ee BEE 9 A ae Sratece i dachtects R Gwe ged a aa ALR KAR cea 9 silence alarm without disarm 0 0 0 cee tees 9 disarming without a remote 00 000 0c eee ee ee 10 silent modena eede a a a dle 11 Pane MOJE gris Measles a kaka p iepa Walter paa aaa AO ag eh wales Ake 11 overmide ModE sca O deat aos 12 false alarm prevention circuitry 2 0 0 0 0000 o 13 diagnostics a i vine eae a 14 arming diagnostics 2 0 2 0 00 cee ee 14 disarming diagnostics 0 0000 cece eee ee 14 system status ChirpS ooo 15 tADIETOLZONCS 22 oro o SOR Gis a DT cas 16 interpreting zone diagnostics oooooooocoocoo 16 anti code grabbing o ooocooccococ tte eee eee 17 high Frequentes ia 17 individual remote recogniti0N ooccoccoccoco eee 18 POWer UD eros e a 18 power saving Mode ooocccco eens 19 programming options ooooccccccoc tte eee 20 installation Options 2 0 00 tenes 23 anti carjacking system 0 060 eee 24 armin
5. Model S100 gt Owner s Guide limited lifetime consumer warranty This Ungo Pro Security system is warranted against defects in material and workmanship The main unit is covered by this limited lifetime warranty This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer This warranty is to the Original Purchaser Owner and to the original vehicle in which it was installed into This warranty is not transferable to any subsequent owner s of the product s Warranty Program Main Unit Limited Lifetime Remote Controls One year from date of purchase Siren One year from date of purchase Shock Sensor One year from date of purchase LED One year from date of purchase Override Switch One year from date of purchase The Warranty does not cover batteries or products deemed damaged through alterations or installation It also does not cover products mishandled misused neglected abused water damaged or with removed altered serial numbers PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT This warranty does not cover the costs incurred for removal or reinstallation of the main unit and or any damage to the vehicle or the vehicle s electrical system The sole responsibility of Clarion Corporation of America Clarion under this Warranty shall be limited to the repair or replacement of the product at the sole discretion of Clarion I
6. anently separate you from your vehicle This system cannot prevent a carjacking attempt however it does en sure that if your vehicle is taken by an unauthorized user it will be dis abled after several progressive warnings as safely as possible Should a carjacking occur the anti carjacking system allows you to concern your self with your personal safety without worrying about your property The Starter Kill and the Anti Carjacking features provide the best com bination of personal safety and property protection available When properly installed the system can never inadvertently stop your vehicle in traffic or on railroad tracks while the vehicle is in operation It is unlike other systems that shut down your engine while it is running This system is designed to perform starter interrupt or starter kill The Starter Kill cannot shut down an already running engine it can only prevent an engine from starting in the first place important Any installation that allows this product to shut down a vehicle s engine when it is running is contrary to the product s design and intended usage and Ungo hereby ex pressly disclaims any liability resulting therefrom arming the anti carjacking system To arm the anti carjacking system turn the ignition to the ON position and press the arm button on the remote remote for one second The parking lights will flash and the siren will chirp once This can be done before driving or while d
7. arms after the 30 second countdown This feature only works if passive arming has been programmed note When programmed for passive arming and active lock if the system is disarmed without a door being opened the system will relock the doors when it passively rearms 20 gt Panic mode enabled disabled with the ignition on Some states have laws against siren capability in a moving vehicle gt Forced passive arming on or off If your system is programmed for passive arming and the forced passive arming feature has been programmed on the system will passively arm after one hour even if a protected entry has been left open This feature is useful if a door has been left ajar when leaving the vehicle Forced passive arming ensures that the security system will be armed in every situation note VVhen the system passively arms after one hour the entry point that has been left open and anything connected to the same zone is bypassed and cannot trigger the system However the remaining inputs to the system are fully operational gt Automatic Engine Disable AED on or off The purpose of this feature is to protect the vehicle from being stolen at all times regardless of whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be disabled 30 seconds after the ignition is turned off Once the key is turned off the LED will flash slowly one half its normal armed rate to indicate the
8. e Mode This is very useful when washing the vehicle or having it serviced In Override Mode the security system will not arm even with the remote remote but all convenience functions door locks trunk release etc will continue to work normally To enter or exit Override Mode OFF Y 2 27 No 1 Turn the ignition on Turn the ignition off Press and release the Override switch within 10 seconds The status LED will light solidly if you are entering Override Mode and it will go out if you are exiting Override Mode To enter or exit Override Mode using the remote 1 2 Se 4 Open any vehicle door Press Press Press P dl amp again The status LED will light solidly if you are entering Override Mode and it will go out if you are exiting Override Mode 12 false alarm prevention circuitry Your system has false alarm prevention circuity It prevents annoying repetitive trigger sequences due to faulty door pin switches or environ mental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm The system will inter pret those triggers as false alarms After the third trigger The system ignores or bypasses that sensor or switch along with any other sen sors or switches sharing the same zone for 60 minutes
9. e Override switch the programmed number of times within 15 seconds After five seconds the system will disarm If it does not you may have waited too long Turn the ignition off and on and try again To enter or exit valet mode gt Turn ignition to RUN position then turn to OFF position Press and release the Override switch within 10 seconds The status LED will light solid if you are entering valet mode and it will go out if you are exiting valet mode To activate Panic Mode gt Press and hold k down for one second To exit Panic Mode gt Press k on the remote To activate Silent Arm Disarm gt Press briefly before arming or disarming and the confirmation chirp s will be eliminated for that one operation only Location of Override switch Number of Override switch pulses for disarming 31 32 Get Started Get Protected A CLARION COMPANY Ungo Pro Security 661 W Redondo Beach Blvd Gardena Ca 90247 800 GO CLARION 2003 Directed Electronics Inc All rights reserved GS100 11 03
10. e control system with a push of a button Over rev protection open hood lockout brake pedal shutoff and automatic timer shutoff are all included This feature is only for automatic trans mission fuel injected gasoline vehicles External Receiver Antenna An optional external receiver antenna can be used to upgrade the remote receiver performance in areas of high radio interference such as military bases airports and hospitals 30 Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet QUICK REFERENCE GUIDE To arm using your remote gt You can activate or arm the system by pressing on your remote for one second When the system arms you will hear a short siren sound or chirp and the parking lights will flash once If the vehicle s power door locks have been connected to the system the doors will lock To disarm using your remote gt To disarm the system press Pal You will hear two chirps and the parking lights will flash twice If power locks are connected to the system the doors will unlock If the siren chirps either four or five times when disarming see Diagnostics section This is called notification of system alarming in your absence Arming while driving gt Press A on your remote for two second while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming without a remote gt Turn on the ignition Press th
11. each remote that is used with the system Then whenever a specific remote is used the system will recall the settings assigned to that remote Individual recognition lets up to four users of the system have different settings that meet their specif ic needs It is almost like having four separate alarms in your vehicle one for each user note This individual recognition cannot be programmed without a Pro Security Programmer and the necessary soft ware Check with your dealer for more information power up gt gt o This system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in valet mode and the battery is dis connected for any reason such as servicing the car when the battery is reconnected the unit will still be in valet mode This applies to all states of the system including arm disarm anti carjacking and valet mode 18 power saving mode ees Your system will automatically enter a power saving mode while armed or in valet mode after a period of time in which no operation has been performed This lowers the current draw to the vehicle s battery Power Saver mode takes over under the following conditions gt Power saving when the system is armed After the system has been armed for 24 hours the LED will flash at half its normal rate decreasing the system s current draw gt Power
12. econd before arming or disarming An optional aux iliary function such as trunk release can be controlled by pressing this button for 1 5 seconds The auxiliary output controls e Button The panic feature is controlled by pressing this button for two seconds A and gd Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously The auxiliary output controls using your system eee The buttons used in the instructions in this manual correspond to the standard configuration Remember this is not the only way your remote may be set up It can be custom configured to meet your needs active arming You can activate or arm the system by pressing A on your remote for one second When the system arms you will hear a short siren sound or chirp and the parking lights will flash once If the vehicle s power door locks have been connected to the system the doors will lock While the system is armed the status LED will flash approximately once per second indicating that the system is actively protecting your vehi cle If you hear a second chirp after arming and see the status LED flashing in groups refer to the Diagnostics section of this guide This extra chirp is notification of an open zone passive arming The system also can be programmed to arm itself automatically called passive arm
13. f it becomes necessary to send the product or any defective part to Clarion the product must be shipped in its original carton or equivalent carton fully insured with shipping charges prepaid Clarion will not assume any responsibility for any loss or damage incurred in shipping ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE UNDER NO CIRCUMSTANCES SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE DIRECT OR CONSEQUENTIAL ARISING OUT OF THE USE OR INABILITY TO USE OF THE PRODUCT BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLU SIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE THE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Should you have any difficulties with the performance of this product during warranty please call 1 800 GO CLARION or visit your local Ungo Pro Security dealer You may also contact the National Service Manager at the following address below for additional service help you may need Clarion Corporation of America Attn National Service Manager 661 W Redondo Beach Blvd Gardena Ca 90247 table of contents limited lifetime consumer warranty oooccoccccococo cece eee eee i standard remote configuration 000
14. g the anti carjacking system 00 000 0000 e eee eee 24 anti carjacking triggered sequence 0 00000 ee eee 25 disarming the anti carjacking system 0 00000 02 o 26 glossary of terms 2 5 02 sands A eal eee ee 27 security amp convenience expansions 000 cee eee eee 29 standard remote configuration controls the Arm function of al controls the Disarm function AUK controls Silent Arm Disarm and an Auxiliary output gt controls the Panic function M P m as 3 and al pressed together control an Auxiliary output what is included One control module A pair of four button remotes A dual stage shock sensor A six tone programmable siren The blue status LED indicator light A push button override switch Starter kill ready circuitry may require additional labor VVVVVV VY External receiver antenna important information Congratulations on the purchase of your state of the art vehicle securi ty system This system has been designed to provide years of trouble free operation Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty This owner s guide should help you to get the most out of your system Please take the time to read it prior to using the system system maintenance The system requires no specific maintenance Your remote contr
15. gered sequence If an instant trigger is desired the progressive door trigger can be programmed off Override pulse count The number of presses of the Override switch required to disarm the security system AED or the Anti Carjacking system can be programmed from one to five presses The default setting is one press Siren tones and chirp volume The output of the siren consists of six different tones in sequence Any of these tones can be eliminated by your dealer resulting in a unique easily identi fiable siren sound The siren chirps can be either full volume or six decibels quieter than the full alarm blast installation options The system has many options that may require extra parts and labor Some of the possibilities are listed here gt Progressive unlocking In most cars with electric power door locks the system can be configured so that when the system is disarmed only the driver s door unlocks A second press of the d button unlocks the other doors gt Anti Carjacking System is designed to help in the safe recovery of your vehicle in case of a carjacking Please refer to the Anti Carjacking System section of this guide for a complete explanation of how this operates 23 anti carjacking system o o The optional anti carjacking system feature is designed to ensure that any unauthorized user of your vehicle even if using your keys and remote control will not be able to perm
16. glass has been struck Backup Battery This keeps the system armed triggers the alarm and keeps the starter kill active if main battery power is disconnected Field Disturbance Sensor An invisible dome of coverage is estab lished by installing the radar sensor Your security system can then react to any intrusions into this field with the triggered sequence Headlight and Parking Light Automation The option will automat ically turn on your parking and headlights when it gets dark In addi tion it will turn your headlights on whenever the windshield wipers are used A remote function can also be used to turn on your parking and headlights for a programmed time Power Trunk Release The channel two output of the system can op erate a factory power release for the vehicle s trunk or hatch An addi tional relay may be required If the factory release is not power activat ed then a trunk release solenoid can often be added Power Window Control Power window control can be provided by one of two systems The firsts system provides control that will roll up two windows automatically when the system is armed or roll two win 29 dows down by using the remote The second system will roll two win dows both up and down This second system also provides one touch switch operation Override Start System For the ultimate in convenience the Override start system can start your vehicle monitor engine functions and power your climat
17. grammed number of times to disarm the Anti Carjacking System 26 note If the Anti Carjacking system has begun its chirping sequence the ignition must be turned off then on to disarm If you are driving the vehicle at the time pull to a safe place away from traffic and follow the triggered sequence disarm procedure glossary of terms o o o ooo Control Unit The brain of your system Usually hidden under the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s functions Starter Kill An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the sys tem is disarmed in valet mode or should the starter interrupt switch itself fail Your system is ready for this feature however installation may require additional labor Input A physical connection to the system An input can be provided by a sensor pinswitch or through an existing system in the vehicle such as ignition or courtesy lights LED Blue light mounted somewhere in the vehicle It is used to indi cate the status of your system It is also used to report triggers and faults in the system or sensors Shock Sensor This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass Siren Noise generating device usually in
18. he system is armed while an input is active door open sensor trigger ing etc the unit will chirp once when arming and then one more time a few seconds later This is notification that the zone is opened or bypassed note The open zone notification will not occur when using Silent Arm Disarm or if chirps have been programmed OFF The security system will ignore the input that was active when the sys tem was armed until the input goes away Three seconds later the sys tem will monitor that input normally For example if your vehicle has interior light exit delay and you arm the system before the interior light goes out you may hear open zone notification chirps Once the light shuts off however the doors are monitored normally disarming diagnostics Extra disarm chirps are notification that the alarm was previously trig gered If four chirps are heard when disarming the system was trig gered in your absence If five chirps are heard a zone was triggered so many times that false alarm prevention circuitry has bypassed that zone The status LED will indicate which zone was involved See Table 14 of Zones section of this guide The system will retain this information in its memory and continue to chirp four or five times each time it is disarmed until the next time the ignition key is turned on system status chirps The siren will chirp when arming disarming the system The pattern of chirps will audibly repor
19. he system will disarm If the system does not disarm you may have waited too long turn the ignition off and on and try again Location of override switch Number of Pulses important The unit can be programmed to respond to one to five pulses of the override switch for the disarm function Be sure to check with the installer for the desired programming 10 silent mode To temporarily turn off the arm or disarm chirps use Silent Arm Disarm Simply press for less than one second before arming or disarming and the confirmation chirp s will be eliminated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you note The warning response to lighter impacts is bypassed if the system is armed using Silent Arm Disarm This ensures that no chirps will be emitted by the siren in an area you want chirp free The system is still fully capable of triggering Only the warning response is bypassed panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your remote Just press e for two sec onds and you will enter Panic Mode The siren will sound and the park ing lights will flash for the programmed siren duration To stop Panic Mode at any time press e on the remote remote again 11 override mode You can prevent your security system from automatically arming and triggering by using Overrid
20. ill This will prevent the vehicle from being restarted thus immobilizing it at that spot Three minutes after the constant siren output begins the flashing parking lights and the siren will stop The starter kill will remain active 25 until the system is disarmed If the door is opened or the ignition is turned off and on in an attempt to restart the car the siren and light flashing will begin again disarming the anti carjacking system Take the time to familiarize yourself with the anti carjacking triggering sequence and the disarm procedure It is important to recognize and identify the trigger sequence and know how to disarm it in case of ac cidental activation Once the anti carjacking system is armed it does not disarm automat ically You must disarm it the next time you operate the vehicle You must disarm it with one of the following procedures If the system has not entered the triggered sequence siren has not started chirping 1 Turn the ignition on S 2 Press S on the remote for one second The lights will flash and the siren will chirp twice If the system has entered the triggered sequence siren has begun chirping pressing the disarm button of the remote will not disarm the Anti Carjacking System To disarm the system during an Anti Carjacking System trigger sequence oF 1 Turn the ignition on x s ES No 2 f is AN gt amp 2 Press the Override switch the pre pro
21. ine which zone caused the system to alarm silence alarm without disarm This feature makes it possible to silence and reset the system while it is triggering without disarming the system If the system is triggered and the siren has been sounding for longer than six seconds pressing or d on the remote will stop the trigger and return the unit to the armed state The system will not disarm but rather reset This pre vents you from disabling the system should you wish to disarm it with out visually checking the vehicle Pressing L after resetting the sys tem will disarm the system pressing this button during the first six sec onds of the triggered sequence will disarm the security system imme 9 J diately The six second timer is provided for your convenience in case the system is accidentally triggered disarming without a remote This feature allows you to disarm the security system without the remote should it be lost damaged or disabled In order to disarm the system without a remote you must have the vehicle s ignition key and know where the override switch is located Be sure to check with the installer for the location and the number of presses of the override switch required to disarm the system To disarm the security system turn the ignition to the ON posi tion Press the override switch the preset number of times one to five times within 15 seconds After five seconds t
22. ing If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the status LED will flash twice as fast as it does when the system is armed The siren will chirp once 20 seconds after the last door has been closed The system is not actually armed at that point The system arms and the doors lock if connected and programmed for passive locking at the 30 second mark but the siren will not chirp The early chirp pro 6 vides you with a 10 second warning prior to arming note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passive ly arm unless forced passive arming is programmed on See Programming Options section of this guide Additionally each time a protected entry is triggered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected as follows gt Light impacts will trigger a warning signal When triggered the siren will chirp and the parking lights will flash for a few seconds Heavy impacts will trigger the system The triggered sequence is between 1 180 seconds of constant siren and flashing parking lights If a door is opened the system will immediately start chirping the siren and flashing the parking light
23. ol is powered by a small lightweight 3 volt lithium battery that will last approximately one year under normal use When the battery weakens operating range will be reduced and the LED on the remote will dim fec id notice This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by the party responsi ble for compliance could void the user s authority to operate this device remote functions lt o This system uses a computer based learn routine to learn the remote buttons This makes it possible to assign any remote button to any sys tem function The remote initially comes programmed with Standard Configuration but may also be customized by an authorized dealer The buttons in all of the instructions in this manual correspond to a Standard Configuration remote standard configuration J A Button The arming function is controlled by pressing this button for one second L Button The disarming function is controlled by pressing this button for one second AUX Button Silent Arm Disarm and an optional auxiliary function are controlled by pressing this button Silent Arm Disarm works by pressing this button for less than one s
24. red but the LED has been reset by turning on the ignition your dealer can still recall the last two zones that were triggered Contact your dealer for details anti code grabbing The receiver and remotes each use mathematical formulas called algo rithms to change their codes each time the remote is used This technol ogy has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the remote in sync with the control unit even if you use the remote control out of range of the vehicle However if the remote has been pressed many times out of range of the vehicle or if the battery has been removed it may get out of sync with the control unit and fail to operate the system To re sync the remote control simply press A of the remote several times within range of the vehicle The alarm will automatically re sync and respond to the remotes normally high frequency Your system transmits and receives at 434 MHz This provides a cleaner spectrum with less interference and a more stable signal Enjoy a phe nomenal increase in range even in areas with high radio interference 17 individual remote recognition Individual remote recognition is a feature available Using the Pro Security Programmer a hand held programming tool your dealer can program many of the system settings The programmer makes it possi ble to program different settings for
25. riving the vehicle Once the system is armed 24 it will initiate its triggered sequence see below if any door is opened and closed If you are forced from the vehicle the system will trigger as the door is opened and closed This is how the system works to com bat intersection carjacking To protect against parking lot carjacking arm the Anti Carjacking System before leaving the vehicle The system will now trigger automatically the next time you or anyone drives the vehicle This helps to protect the vehicle if someone takes your keys and remote by force in a parking lot note If the AntiCarjacking system is armed while operating the vehicle and not disarmed prior to leaving the vehicle it is still armed and will trigger the next time the vehicle is driven anti carjacking triggered sequence Fifteen seconds after the last door has closed the system s status LED will begin flashing This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking Forty five seconds later the siren begins chirping and the parking lights begin flashing This time could be used to notify authorities that your vehicle has been hijacked and tell them what the Anti Carjacking system will do next Fifteen seconds after the siren chirps begin the siren s output will change to a continuous blast From this point on when the ignition key is turned off the system will immediately turn on the starter k
26. s Three seconds later the siren output changes to a continuous blast This progres sive response gives you time to disarm the system with your remote if you inadvertently open the door while the system is armed while still providing an instant response even if the door is immediately closed Turning on the ignition key will trip the same two stage response as opening a door The optional starter kill prevents the vehicle s starter from cranking remote sensor bypass Remote Sensor Bypass allows you to select which of the security sys tem s inputs or sensors will be active and which will be bypassed at the time that the system is armed See the Table of Zones section of this guide Pressing system will activate the Remote Sensor Bypass feature Each time E A again within five seconds of arming the security is pressed again a different security level is selected The different secu rity levels can be selected as follows gt Press A one time The siren chirps once The system is armed Press amp a second time within five seconds The siren chirps twice followed by a long chirp Zone 2 is now bypassed Press A a third time within five seconds The siren chirps three times followed by a long chirp Zone 4 is now bypassed Press A a fourth time within five seconds The siren chirps four times followed by a long chirp Zones 2
27. saving in valet mode When the system enters valet mode the LED illuminates steadily If the vehicle is not used ignition is not turned on for a period of one hour while the system is in valet mode the LED will shut off If the system remains in valet mode the LED will come back on the next time the ignition is turned on and then back off 19 programming options ese Programming options control what your system does during normal operation and require few or no additional parts However some may require additional installation labor The following is a list of the program settings with the factory settings in Bold gt Active arming only with the remote or passive arming auto matic arming 30 seconds after the last door has been closed gt Arming disarming confirmation siren chirps on or off gt The ignition controlled door lock feature on or off With this feature on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned off The system will not lock the doors when the ignition is turned on with any door open If your installer is programming the security system with the Pro Security Programmer ignition lock and unlock are independent features and can be programmed separately gt Passive door locking with passive arming or active door locking only when arming with the remote Passive locking allows the vehicle s doors to lock when the security system passively
28. stalled in the engine compart 27 ment of the vehicle It is responsible for generating the chirps you hear as well as the six tones you hear while the alarm is triggered Remote Hand held remote control which operates the various func tions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration Override Switch A small push button switch mounted somewhere inside the vehicle It is used to override the alarm when a remote is lost or damaged or to enter or exit valet mode Warn Away Lighter impacts to the vehicle will generate the Warning Zone response It consists of several seconds of siren chirps and park ing light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Two or more inputs often share the same zone 28 security amp convenience expansions _ Here we have listed only some of the many expansion options avail able Please contact your dealer for a complete explanation of all the options available to you Audio Sensor Metal on glass glass cracking and breaking glass each produce distinctive acoustic signatures The audio sensor uses a micro phone to pick up sounds and then analyzes them with proprietary acoustic software to determine if the
29. t the system s status as described below Action Arm Arm Disarm Disarm Disarm Number of Chirps 1 1 3 second delay 1 Description System armed System armed with open zone notification System disarmed System disarmed with previous alarm notice System disarmed false alarm circuitry active 15 table of zones The zone number is the number of LED flashes used by the system to identify that input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed Zone Number Dealer Installed of LED Flashes Description Options 1 Instant trigger often used for hood trunk pinswitches 2 Instant trigger a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger for optional sensors 5 Ignition trigger interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnos tics If you receive a open zone notification when arming or a notifica tion of an alarm in your absence when disarming look at the LED Active or triggered zones will be indicated by a pattern of blinks by the LED Example If Zone 3 was active or triggered the LED will blink three times with a two second pause Then it will blink three times again and repeat until the ignition is turned on 16 note Your system stores the last two triggered zones in memo ry If your system has been trigge
Download Pdf Manuals
Related Search