Clam Corp Fish Trap X 8236 User's Manual
Contents
1. 8236 Height 68 inches Length 79 inches Width 62 inches Weight 120 Ibs p n 108236 Instruction No 101914 Clam Customer Service Information NOTICE ONCE USED THIS SHELTER CANNOT BE RETURNED TO THE STORE IF YOU HAVE A WARRANTY CLAIM PLEASE CONTACT CLAM CORP CUSTOMER SERVICE BY EMAIL INQUIREY OR DIRECT BY CALLING m Customer Service Hrs 9am to 4pm Mon Fri Central Standard Time m Clam Corporation Inc 600 Clydesdale Trail Tole a dover look Medina MN 55340 lt q _ Phone 763 231 4120 m po m Fax 763 231 4121 Qu 0 l m m Email customerservice clamcorp com J m Website www clamcorp com CORP RATION Bill of Materials ITEM QTY P N DESCRIPTION ITEM OTY P N DESCRIPTION 1 4 101048 BLOCK SLIDE 17 1 101811 BASE MEDIUM XTR 2 18 101081 WASHER 1 4 FLAT 18 2 101813 BRKT RAIL HANGER 3 26 101082 LOCKNUT 1 4 THIN 19 1 101817 BRKT FRONTSEAT 4 8 101088 SCREW 1 4 20 X 0 75 PHILLIPS 20 6 101829 POLEASSY STRAIGHT POLE 5 2 101146 ANGLE 9 LONG ALUMINUM ANGLE 21 2 101830 POLEASSY BENTCANOPY 6 4 101147 SCREW 10 X 1 LONG PHILLIPS 22 2 101836 POLE ASSY FRONT SPREADER 7 1 101399 PLATE 6 SQUARE SWIVEL 23 1 101840 POLE ASSY REAR SPREADER 8 1 101424 BRKT REARSEAT 24 1 101842 TENT X C oj 9 4 101429 CAP 1 1 8 TUBE 22. n 101652 Step Four Seat Tube Assembly Completed in Step Three Seat Assembly Completed in Step Two 1 4 Thin Locknut p n 101082 1 1 8 Diameter Tube Cap p n 101429 Rear Seat Bracket p n 101424 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 Latch Clip p n 101442 Slide the Tubes of the assembly completed in Step Three through the Slide Blocks of the Seat Assembly completed in ore Two When the combined assembly is completed set aside for installation following the shelter assembly Step Five m Mongo e 1 4 Flat Washer 1 4 x 1 1 2 Screw 1 4 Thin Locknut p n 101082 Seat Rail Tube p n 101907 p n 101473 Use these two holes for mounting Canopy Bracket on opposite narrow end of Base 1 4 x 3 4 Screw p n 101088 Base and Bracket are cut away for visual clarity XTR Canopy Bracket p n 101810 1 4 Flat Washer p n 101081 Medium XTR Base p n 101811 Straight Canopy Pole Assy w Cap pin 101829 1 4 Thin Locknut p n 101082 1 4 Flat Washer p n 101082 ser je Pole Cap included with Pole Assy p n 101826 1 4 X 2 1 2 Screw p n 101906 Note Snap Button Direction all Straight Canopy Poles 1 4 Thin Locknut p n 101082 1 4 X 2 1 2 Screw p n 101906 Canopy Pole Cap included with Pole Assy p n 101826 Bent Canopy Pole Assy w Cap p
3. n 101830 1 4 Flat Washer p n 101081 Step Seven Rear Spreader Assembly p n 101840 Canopy Hoop Pole Assembly p n 101863 Canopy Pole Assembly hole of the Base hp f engagement hole of the Canopy Hoop snap button of the Canopy Pole Slide the Canopy Hoop Poles onto the Straight Canopy Poles until the snap buttons engage the holes near the ends of each Canopy Hoop Pole Extend the Rear Spreader Pole about 12 inches and tighten the tension knob Next Poke the tip of the Rear Spreader Pole into the hole of the Base and use to temporarily support the Canopy Hoop Poles as pictured 10 A Tent p n 101842 Sidewall Velcro lt 1 Drape the Tent over the supported hoops from the last step then under the Tent and spread out the Canop y Hoop Poles and then attach the Roof Velcro as you go When completed lay the attached Canopy Hoop Poles down onto the base Take the not installed Canopy Hoop Pole and prepare to feed the length of the pole through the Porch Hoop Sleeves sewn on the Tent under the front door Determine the correct orientation for the holes of the Canopy Hoop Pole so that the will mate properly with the snap buttons of the Bent Canopy Poles Next slide Canopy Hoop Pole through the Sleeve an then engage the snap buttons as you did in the prior step Gather the ends of the Draft Flap and pull them together stretching its length against the sidewall of the base Secure t
4. 5 4 101862 POLEASSY CANOPYHOOP 10 1 101442 CLIP LATCH 26 2 101864 POLEASSY ROOFSPREADER C 11 1 101466 HAMMOCK CLOTH ACCESSORY 27 1 101905 SEATASSY TWO TONE 12 8 101470 BOLT 1 4 DIA HEX HEAD BOLT X 1 2 28 8 101906 SCREW 1 4 DIA X 2 1 2 PHILLIPS 13 2 101473 SCREW 1 4 DIA X 1 1 2 PHILLIPS 29 1 101907 TUBE MED XTR SEATRAIL SCREW 1 4 DIA X 1 3 4 PHILLIPS 30 1 101909 MOLDING U CHANNEL 15 2 101652 TUBE 1 1 8 DIA 31 20 101938 SCREW 48 PHILLIPS id 16 2 101810 BRKT XTRCANOPY zj pp eee Seat Parts Diagram See pg 4 for Assembly Step One 10 x 1 Long Philips Screw _ 1 4 Thin Locknut p n 101147 p n 101082 1 1 2 X 1 3 4 Aluminum Angle X 9 Long p n 101146 Slide Block p n 101048 6 Square Swivel Plate p n 101399 1 4 Hex Head Bolt X 1 2 Long p n 101470 Step Two 1 4 Dia Hex Head Bolt X 1 2 Long p n 101470 Assembly from Step One Folding Seat Assembly shown folded amp bottom side up p n 101905 When completed set Seat Assembly aside for use in Step Four Step Three 1 4 Thin Locknut p n 101082 SHIPPED PACKED WITH TENT Cloth Accessory Hammock p n 101466 Front Seat Bracket p n 101817 1 1 8 Dia Tube Cap p n 101429 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 1 1 8 Dia Tube p
5. available for purchase at www clamcorp com Two install the Tow Rope drill two 1 2 holes in the sloped front of the Base Knot the ends of the Tow Rope after routing through the drilled holes Tow Rope p n 101249 15 Safety Instructions Please fully understand and follow all safety instructions as outlined Failure to do so could result in severe injury or death Do not use open flame heaters in your ice shelter Injury or death may result from fire if tent fabric is exposed to open flame The tent is not fireproof but the fabric is treated with a fire retardant that meets CPAI 84 specifications Application of any foreign substance may render the flame retardant properties ineffective Ice Armor fabric will melt when contact is made with hot surfaces i e heaters Death from asphyxiation may result from use of oxygen depleting heaters Open all vents for fresh air ventilation Never leave shelter unattended when set up Due to the increase in traffic snowmobiles autos etc on area lakes ice fishing can be hazardous at night If you choose to fish at night or in poor visibility conditions be sure to take precautions with lights or reflectors to show drivers your whereabouts Night time exterior reflectors must be visible to reduce risk of collisions Clam Corporation Inc warrants to the original retail purchaser that all Clams are free from manufacturers defects for one 1 year from the date of the or
6. he nt bla vi buckle and then align and attach the Velcro at the ends of the Draft Flap Next attach the Sidewall Velcro on each side of the Tent With the Tent now secured at all Velcro locations remove the Rear Spreader Pole that was used to temporarily support the Canopy Hoop Poles The Tent can now be set in the next step 11 op TAS BS p O thru 2 inches Cut away for visual clarity Porch Area Dorch Area U Channel Molding Vi p n 101909 about 12 inches To set the Tent grasp the Tent material at the rear of the shelter and pull it downward Observe the Porch Area of the tent lifting accordingly as you pull When the U Channel Molding is correctly installed the first Canopy Hoop Pole will lightiy touch the floor or will measure anywhere from 0 2 inches To achieve this condition start by finding the center of the Molding From behind the unit pull the mid point of the Tent downward and fold the Tent material under the Base Lip Press the midpoint of the Molding over the Tent material and the Base Lip Continue pressing outward from the mid point in both directions until you have secured about twelve inches of material to the base Having temporarily secured the tent to the base verify the proper position of the Canopy Hoop Pole at the front of the shelter If the position is not within the recommended measurement readjust the molding position and then recheck unti
7. iginal purchase Warranty does not cover cracked windows tent tears broken or bent hoops due to high wind weather conditions or unattended use Clam Corporation will replace or repair any part found defective within the one 1 year time limit All parts must be returned to Clam Corporation Inc Before returning any parts you must first call or write and acquire a return authorization All returns must be returned postage prepaid and include the original cash register receipt date and purchase price Limitation of Liability It is expressly understood that Clam Corporation liability for tts products whether due to breach of warranty negligence strict liability or otherwise is limited to the repair of the product as stated above Clam Corporation is not liable for any injury loss damage or expense whether direct or consequential including but not limited to loss of use income profit or damage to material arising in connection with the sale installation use of inability to use or the repair or replacement of Clam Corporation products Clam Corporation reserves the right to make alterations or modifications in its products at any time which in its opinion may improve the performance and efficiency of the product It shall not be obligated to make such alterations or modifications to products already in service 16
8. l the proper positioning is achieved Complete the installation of the U Channel Molding in the next step 12 Step fen Back Edge of Canopy Bracket Roof Spreader Pole Rear Spreader Pole p n 101864 p n 101840 8 Phillips Screw gt Front Spreader Pole p n 101938 p n 101836 Now that you have the correct measurement under your Canopy Hoop Pole continue applying the U Channel Molding around the shelter one direction from center and then the other pulling the material as you go so that surface is void of any major creases and is relatively wrinkle free From outside the Tent feel where the molding ends in korena to the Rear Edge of the Canopy Brackets If either end of the Molding extends past the Rear Edge of the Canopy Pole Brackets trim the Molding with a utility knife or side cutters to end an inch or two before the Rear Edge Install the Front Rear and Roof Spreader Poles as indicated ja bog the Front and Rear Spreader Poles to tighten the fit of the tent With everyihing fully extended the Canopy Hoop Pole at the front of the unit should be pushing against the floor Ifit seems that the tent is not tight enough after doing so or else you are unable to stretch the Tent enough to get this to happen you probably need to readjust the molding position If everything still looks good secure the Molding with the included 8 Phillips Screws Evenly space them about every ten to twelve inches and
9. or in areas that would benefit most such as inner curves etc Since there aren t any predrilled holes it s advisable to use a powered driver for this operation 13 Seating Installation Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the outside edge of the Base Lip With the Latch Clip hanging freely tilt the complete assembly downward until the interior of the Rear Seat Bracket surrounds the Support Tube Latch Clip Seating Installation cont Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket Secure the position of the Latch Clip by pushing it into the two holes located above the horizontal slot of the Rear Seat Bracket Bracket Holes l E ko Latch Clip N K N N SS i SECURED POSITION po NN a SSE s Swing the Latch Clip under the Support Tube e Squeeze the Latch Clip and push it through the slot of the Rear Seat Bracket a Secure by pushing the ends of the Latch Clip into the holes of the Seat Bracket Seat Bracket Support Tube WARNING ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM Included is a Tow Rope for those not planning to install the optional Tow Hitch Assembly
Download Pdf Manuals
Related Search