Citizen Systems CT-S601 User's Manual
Contents
1. Cash drawer kick out cable connector Screw for ground wire N CAUTION Connect only the cash drawer kick out cable connector to the cash drawer kick out connector Do not connect a telephone line Signals cannot be output from the cash drawer kick out connector while printing 9 1 Connector pin configuration DRAWER1 Cash drawer 1 drive signal Hh e pops Hirose or equivalen DRSW Cash drawer switch input mi Applicable connector 4 VDR Cash drawer drive power supply TM3P 66P Hirose or DRAWER2 Cash drawer 2 drive signal eguivalent GND Signal ground common groundon circuits 2 Electric characteristics 1 Drive voltage 24 VDC 2 Drive current Approx 1 A max not to exceed 510 ms 3 DRSW signal Signal levels L 0 8 V 2 to 3 3 3 DRSW signal DRSW signal status can be tested with the DLE EOT GS a or GS r command or at pin 34 on the parallel interface port 4 Drive circuit Cash drawer kick out connector Shielded Lex i 3 3V VDR Cash drawer open close switch 1 Cash drawer Printer N CAUTION Cash drawers 1 and 2 cannot be operated at the same time B The solenoid used for the cash drawer should be 24 Q or more Do not allow the electric current to exceed 1 A Excessive current could damage or burn out the circuits D 3 4 Precautions for Installing the Printer2. LINE THERMAL PRINTER MODEL CT S601 User s Manual CITIZEN SYSTEMS JAPAN CO LTD If you want to dispose of this product do not mix it with general household waste There is a separate collection systems for used electronics products in accordance with legislation under the WEEE Directive Directive 2002 96 EC and is effective only within European Union Wenn Sie dieses Produkt entsorgen wollen dann tun Sie dies bitte nicht zusammen mit dem Haushaltsmull Es gibt im Rahmen der WEEE Direktive innerhalb der Europ ischen Union Direktive 2002 96 EC gesetzliche Bestimmungen f r separate Sammelsysteme f r gebrauchte elektronische Ger te und Produkte Si vous souhaitez vous d barrasser de cet appareil ne le mettez pas la poubelle avec vos ordures m nag res ll existe un syst me de r cup ration distinct pour les vieux appareils lectroniques conform ment la l gislation WEEE sur le recyclage des d chets des quipements lectriques et lectroniques Directive 2002 96 EC qui est uniquement valable dans les pays de l Union europ enne Les appareils et les machines lectriques et lectroniques contiennent souvent des mati res dangereuses pour l homme et l environnement si vous les utilisez et vous vous en d barrassez de facon inappropri e Si desea deshacerse de este producto no lo mezcle con residuos dom sticos de car cter general Existe un sistema de recogida selectiva de aparatos electr ni
3. 42 CITIZEN SYSTEMS JAPAN CO LTD 6 1 12 Tanashi cho Nishi Tokyo shi Tokyo 188 8511 Japan Tel 81 0 42 468 4608 Fax 81 0 42 468 4996 http www citizen systems co jp TZ74916 00F A87667E 09 10
4. The printer can be used horizontally vertically or installed on a wall However the 56015 built in power supply type cannot be used vertically or installed on a wall Use the optional stand for vertical applications and the optional brackets for wall installations Please refer to the manual for further details Horizontal position Vertical position Wall installation Change the paper near end sensor settings for vertical and wall installations The factory setting for the paper near end sensor is for horizontal installations Refer 3 7 Adjusting the Paper Near end Sensor N CAUTION Do not use the printer under the following conditions Locations subject to vibration or instability Locations that are very dirty or dusty Locations where the printer is not level e The printer may fall and cause an injury e The quality of printing may deteriorate M Oriented other than as specified e The printer may malfunction be damaged or cause an electric shock Precautions for horizontal installations E Do not set cutting to full cut Doing so may cause cutter jams Precautions for vertical wall installations B Adjust the paper near end sensor D e 3 5 Partition for Paper Roll Set the partition to the width of the paper roll you are loading The partition is set at the factory to the position shown below For 3 inch type 80 mm wide paper roll For 2 inch type 58 mm wide paper ro
5. M Avoid using torn pieces of paper or paper spliced with plastic adhesive tape Avoid forcibly pulling already loaded paper by hand Avoid using a sharp pointed device to operate panel buttons M Be sure to firmly insert the cable plugs into their mating sockets e A cross connection may damage the printer s internal electronics or the host system s hardware B Only use the printer with devices that have designated solenoid specifications for the cash drawer interface connector Neglecting this caution may result in malfunction or failure N CAUTION To prevent injury and printer failures from worsening observe the following B While the paper cover is open be careful to not touch the manual cutter that is in the paper eject slot E Do not touch the printing surface of the thermal head B Do not touch any of the moving parts e g paper cutter gears active electric parts while the printer is working Bin case of trouble do not attempt to repair the printer Ask Citizen Systems service for repair E careful that the covers do not pinch your hands or fingers E careful of the sharp edges on the printer Do not allow them to injure you or damage property e May result in electric shock burn or injury If the printer emits smoke an odd smell or unusual noise while printing immediately abort the current print session and unplug the printer from the electric outlet 1 DAILY MAINTENANCE Obse
6. TTT Notes 1 If the paper cover or front cover is open in standby 2 f the paper cover or front cover is open when printing or feeding paper 3 Buzzer sounds when MSWB 1 buzzer setting is set to ON 5 OTHER 5 1 External Views and Dimensions Unit mm 192 mad lu 120 Yd E AC adapter type 36 5 2 Printing Paper Use the paper shown in the following table or paper of the same quality Paper type Product name Recommended TF50KS E2D from Nippon Paper PD150R or PD160R from Ohji Paper PA220AG HP220A HP220AB 1 F230AA P220AB or PB670 2 color paper from Mitsubishi Paper Unit mm Paper width 83 Paper width 80 Printable side LO CH S Paper 65 75 75 85 thickness um Core inner 1 25 4 diameter d mm Core outer diameter D mm N CAUTION Use paper that is wound as follows B Not creased and fits tight to the core Not folded B Not glued to the core Rolled with the printable side out cg 5 3 Manual Setting of Memory Switches Memory switches are used to set various printer settings The memory switches can be set manually set by hand on the printer or by commands This section explains how to perform manual settings For information on how to set the memory switches using commands please refe
7. following conditions M Avoid locations subject to vibration or instability M Avoid locations where the printer is not level e The printer may fall and cause an injury The quality of printing may deteriorate B Do not obstruct the printer s air vents B Do not place anything on the printer M Do not cover or wrap the printer in cloth or blankets Doing so could cause heat to build up and deform the case or start a fire M Avoid using the printer near a radio or TV set or from supplying it from the same electric outlet as these appliances Avoid using the printer interconnected with a cable or cord that has no protection against noise For interconnections use shielded or a twisted pair of cables and ferrite cores or other anti noise devices M Avoid using the printer with a device that is a strong source of noise e The printer may have an adverse effect on nearby radio or TV transmissions There may also be cases when nearby electrical appliances adversely influence the printer causing data errors or malfunction B installed in any orientation other than those specified e Malfunction failure or electric shock may result Connect the printer to a ground Electric leakage may cause an electric shock B Do not connect the printer s ground to any of the following Gas piping e A gas explosion could result Telephone line ground Lightning rod e f lightning strikes a large surge of current may cause fire
8. low paper near end or there is no paper paper end e ERROR LED red Flashes if the print head is hot the paper cover is open a cutter lock occurs and so forth e FEED button Press this button to feed paper In case of a cutter lock remove the cause of the lock close the paper cover and then press the FEED button The printer enters the mode for setting memory switches and running self printing Ei Refer to 4 4 Self printing gt Refer to 4 6 Error Messages E Refer to 5 3 Manual Setting of Memory Switches 218 Rear connectors Cash drawer Interface connector kick out Power connector AC adapter type serial parallel USB etc connector AC inlet built in power supply type Interface connector serial parallel USB etc Connects to the interface cable The serial interface board is equipped with a DIP switch Cash drawer kick out connector Connects to the cable from the cash drawer Power connector AC adapter type Connects to the AC adapter cable AC inlet built in power supply type Connects to the AC power cord 14 2 2 Inside the paper cover Paper end sensor PE sensor Platen Auto cutter Button to change paper near end sensor Manual cutter Print head thermal Paper thickness selection lever Paper near end sensor PNE sensor e Platen Feeds the paper Paper near end sensor PNE sensor Detects when the paper i
9. or shock Water pipes e Plastic water pipes should not be used for grounding Those approved by a Waterworks Department may be used M Before connecting or disconnecting the grounding lead to or from the printer always unplug it from the electric outlet PRECAUTIONS IN HANDLING THE PRINTER N WARNING Please observe the following precautions for power source and power cord E Do not plug or unplug the power cord with a wet hand M Use the printer only at the specified supply voltage and frequency Use only the specified AC adapter with the printer B Check to make sure that the supply outlet from which the printer is powered has a sufficient capacity B Do not supply the printer from a power strip or current tap shared with other appliances E Do not plug the power cord into an electric outlet with dust or debris left on the plug E Do not use a deformed or damaged power cord E Do not move the printer while its power is Neglecting to handle it properly may result in printer failure emission of smoke fire or electric shock e An overload may cause the power cord to overheat catch fire or the circuit breaker to trip B Do not allow anything to rest on the power cord Do not place the printer where the power cord may be stepped on B Do not use or carry the printer with its power cord bent twisted or pulled E Do not attempt to modify the power cord unnecessarily M Do not place the power cord near a
10. 0 Print Character Print Mode Width Space CITIZEN CBM1000 58 mm Auto Valid 432dots linefeed WEE Auto Valid 576dots linefeed Cream S8mm Weitbata Invalid asados omm WaitData invalid S 6dots Auto Valid 432dots linefeed 60 mm Auto Valid 436dots linefeed 80 mm Auto Valid 576dots linefeed 83 mm Auto Valid 640dots linefeed 58 mm Odot 1dot WaitData 80 Odot WaitData iin WaitData 203dpi WaitData 420dots WaitData Invalid 436405 WaitData Invalid 57605 Individual setting mode Set the memory switches individually Do the settings while confirming the memory switch function and settings on the printout 1 2 3 Load paper While the paper cover is open press and hold the FEED button while turning the power on Press the FEED button twice and close the paper cover The printer enters the mode for setting memory switches individually The printer prints Memory SW 1 and the current setting 0 off or 1 on The current settings for memory switches 7 to 10 are not printed Memory SW 1 00000000 Current setting Current memory switch Press the FEED button The list of memory switches cycles through in order from Memory SW 1 gt Memory SW 2 gt Memory SW 10 gt Save To Memory Memory SW 1 gt each time the FEED button is pressed Press the FEED button until the number for the memory s
11. 38400 bps 57600 bps 115200 bps oS ai ie uU MSW8 1 Print Width 576dots 640dots 576dots 512dots 436dots 432dots 3 inch type 420dots 384dots 360dots 390dots 546dots 384dots 390dots 546dots 2 inch type MSW8 2 Paper Type 1 Color 1 Color Normal 2 Color Normal Normal 1 Code Page PC 437 PC 437 Katakana PC 850 858 PC 860 PC 863 PC 865 PC 852 PC 866 PC 857 WPC1252 Space page PC 864 Thai Code 18 MSW9 2 Int Char Set USA France Germany England Denmark Sweden Italy Spain Japan Norway Denmark 2 Spain 2 Latin America Korea Croatia China MSW9 3 ON OFF MSW9 4 JIS Shift JIS JIS 1015 Shift JIS MSW10 1 Print Density 100 70 96 75 80 96 85 96 90 96 95 96 100 105 96 110 96 115 96 120 96 125 96 130 96 135 96 140 96 MSW10 2 Print Speed Level 9 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 MSW10 3 ACK Timing Before Busy Before Busy Same Period After Busy MSW104 Reeva Jl MSW10 6 Tone 1 Tone 2 Tone 3 Tone 4 Note f print data is very dense the print head is hot data transmission is slow or some other conditions the motor and printing may occasionally stop which causes white stripes in the printout To print high density data set MSW2 3 Spool Print to ON to reduce striping although this increases the time before printing starts For a serial interface increase the transmission speed to prevent the motor from stopping
12. Printers with a USB interface do not have DIP switches so the DIP switches all appear off on the self printing printout BF 4 5 Hexadecimal Dump Printing Print received data in hexadecimal If problems such as missing or duplicated data occur this function allows you to check whether or not the printer is receiving data correctly How to do hexadecimal dump printing 1 Load paper 2 While the paper cover is open press and hold the FEED button while turning the power on and then close the paper cover 3 The printer prints HEX dump print mode followed by the received data printed in hexadecimal numbers and some characters How to stop hexadecimal dump printin Do one of the following to stop printing Press the FEED button three times a row Turn off the power e Receive a reset command from an interface N CAUTION un B The printer prints if there is no character corresponding to the data None of the commands function during hexadecimal dump printing B If print data does not cover a complete line press the FEED button to advance the paper Print example HEX dump print mode 61 62 63 64 65 66 67 OA OD OD OD OD abcdefg GID JE 5 gone a 4 6 Error Messages Paper end The end of the roll of paper is detected at two stages paper near end and paper end When paper near end is detected the PAPER LED lights Prepare a new paper roll When paper end is detected the PAPE
13. R LED and ERROR LED light Load a new paper roll Paper cover open Do not open the paper cover during printing If the paper cover is opened the ERROR LED lights or flashes Check the paper and always pull a few cm of paper straight out of the printer before closing the paper cover Printing resumes Sending a command to resume printing may be required depending on the memory switch setting Cutter locked If the auto cutter cannot move because of a paper jam or something else the ERROR LED flashes Remove the cause of the trouble and press the FEED button If the auto cutter still does not operate and the paper cover does not open refer to 4 3 Clearing a Cutter Lock 2 Cm Refer to 4 3 Clearing a Cutter Lock 2 Print head hot When you print dense characters dark images or for an extended time in a hot environment the print head temperature increases If the print head exceeds a specified temperature the printer stops printing and waits for the print head to cool When this happens the ERROR LED flashes Printing resumes automatically when the print head cools The status display for various messages is shown below POWER LED PAPER LED ERROR LED Status green orange red 7 Papernearem oms Lgs Paper cover open or front Lights Lights Yes eee E TT m m Paper cover open or front Lights Yes mmm m LITTLE Doo p m a em o ue ICT oo TTT om oc oo AW uq poem mmm V
14. anywhere maximum 3 inch 83 mm paper roll size Choose from two models with either 3 inch 83 80 mm or 2 inch 60 58 mm wide paper rolls Built in power supply or AC adapter types available Printer status and errors indicated by LED and a buzzer Equipped with a fast and quiet cutter Easy to clear cutter jams e Interchangeable interface Built in cash drawer kick out interface e Memory switches make customization possible Store user defined characters and logos on user memory Barcode and 2D barcode printing supported 2 color printing supported when specified paper used Driver and utility software included 1 2 Unpacking Make sure the following items are included with your printer e Printer e Interface cover AC power cord Power switch cover e Sample paper roll e CD ROM Ll l2 Quick Start Guide 1 AC adapter 1 1 e USB cable 2 1 Notes 1 CT S601A only 2 USB interface types only In designated markets C 2 47 AC powercord USBcable Sample Quick Start paper roll Guide CT S601S ri el i Built in power supply type CD ROM Interface cover 36AD3 AC adapter built in AC adapter AC power USB cable Sample 36AD2 cord paper roll n e Power switch EST Quick Start cover CD ROM Interface cover Guide 1 3 Model Classification Model numbers indicate printer features according to the following system Power suppl
15. be stored in memory Settings remain stored in the memory even if the printer is turned off 16 3 SETUP 3 1 Connecting the AC Power Cord 1 Turn off the power 2 For the built in power type printer connect the AC power cord to the AC inlet and insert the plug into an electric outlet For the AC adapter type printer connect the cable connector of the AC adapter to the power connector Next connect the AC power cord to the AC inlet and insert the plug into an electric outlet AC inlet S AC adapter AC inlet AC power cord AC power cord Built in power supply type AC adapter type N CAUTION M Use only an AC adapter that complies with the specified ratings B Always hold the AC adapter s cable connector by the connector when removing or inserting it B Use an AC power source that does not also supply power to equipment that generates electromagnetic noise B Pulling on the AC power cord may damage it cause a fire electric shock or break a Wire B if a lightning storm is approaching unplug the AC power cord from the electric outlet A lightning strike may cause a fire or electric shock B Keep the AC power cord away from heat generating appliances The insulation on the AC power cord may melt and cause a fire or electric shock E if the printer is not going to be used for a long time unplug the AC power cord from the electric outlet B Place the AC power cord so that people do
16. cautions for Installing the Printer aaa 21 3 5 Partition for Paper ROW d en o is Rei 22 3 6 Setting the DIP Switch on the Serial Interface Board 23 3 7 Adjusting the Paper Near end Sensor 24 3 8 Setting Paper Thickness eese nnne nen 25 SA DN e it Le WEE 26 3 10 Attaching the Power Switch Cover 27 3 11 Attaching the Interface Cover 28 3 12 Removing the Interface Cover 28 4 MAINTENANCE AND TROUBLESHOOTING 29 4 1 P riodic Cleaning EE 29 4 2 Clearing a Cutter LOck 1 reiia 30 4 3 Clearing a Cutter LOCK 2 ener 31 44 5el1 PiINUN09 lt gids 32 4 5 Hexadecimal Dump Rrmtmg 33 4 6 eg teme iso de oci tien ivo 34 Bi OTHER ee eege 36 5 1 External Views and 36 5 2 Printing adas 37 5 3 Manual Setting of Memory Switches 38 1 GENERAL OUTLINE The CT S601 line thermal printer series is designed for use with a broad array of terminal equipment including data POS and kitchen terminals These printers have extensive features so they can be used in a wide range of applications High speed 200 mm s printing Design so compact it can be installed
17. cos usados seg n establece la legislaci n prevista por la Directiva 2002 96 CE sobre residuos de aparatos el ctricos y electr nicos RAEE vigente nicamente en la Uni n Europea Se desiderate gettare via questo prodotto non mescolatelo ai rifiuti generici di casa Esiste un sistema di raccolta separato per i prodotti elettronici usati in conformit alla legislazione RAEE Direttiva 2002 96 CE valida solo all interno dell Unione Europea Deponeer dit product niet bij het gewone huishoudelijk afval wanneer u het wilt verwijderen Er bestaat ingevolge de WEEE richtlijn Richtlijn 2002 96 EG een speciaal wettelijk voorgeschreven verzamelsysteem voor gebruikte elektronische producten welk alleen geldt binnen de Europese Unie Hvis du vil skille dig af med dette produkt ma du ikke smide det ud sammen med dit almindelige husholdningsaffald Der findes et separat indsamlingssystem for udtjente elektroniske produkter i overensstemmelse med lovgivningen under WEEE direktivet direktiv 2002 96 EC som kun er gaeldende i den Europaeiske Union Se quiser deitar fora este produto n o o misture com o lixo comum De acordo com a legislac o que decorre da Directiva REEE Res duos de Equipamentos El ctricos e Electr nicos 2002 96 CE existe um sistema de recolha separado para os equipamentos electr nicos fora de uso em vigor apenas na Uni o Europeia Jezeli zamierzasz pozby sie tego produktu nie wyrzucaj go razem ze zwyktymi domow
18. ctory settings unless printing on thick paper or there is a problem with the print density Ei Refer to 1 3 Model Classification 1 Turn off the power 2 Press the cover open lever 3 Open the paper cover 4 Set the paper thickness selection lever to A for thick paper or B for regular paper Gently press on the side of the lever with a pointed object such as a pen to move the paper thickness selection lever Paper thickness selection lever A Thick paper 85 um 150 um B Regular paper 65 um 85 um Factory setting 96 3 9 Loading Paper 1 Press the cover open lever while the power is on 2 Open the paper cover 3 Load the paper roll so that the printable side of the paper is facing down as shown by arrow A 4 Pull a few cm of paper straight out in the direction of arrow B 5 Close the paper cover in the direction of arrow C until you hear a click Paper is fed and cut automatically if the factory settings are set E Refer to 5 3 Manual Setting of Memory Switches N CAUTION B Always use the specified types of paper rolls B Confirm that the paper roll is set correctly If the paper is skewed and not coming straight out of the paper cover open it and straighten the paper Always pull a few cm of paper straight out of the printer if you open the paper cover while paper is loaded M Press on the center of the pa
19. g describes the degree of hazard and damage that could occur if the printer is improperly operated by ignoring the instructions indicated by the warning symbols N WARNING Neglecting precautions indicated by this symbol may result in fatal or serious injury N CAUTION Neglecting precautions indicated by this symbol may result in injury or damage to property A A o This symbol is used to alert your attention to important items This symbol is used to alert you to the danger of electric shock or electrostatic damage This symbol denotes a request to unplug the printer from the wall outlet This symbol is used to indicate that the power supply must be grounded This symbol is used to indicate useful information such as procedures instructions or the like This symbol is used to indicate prohibited actions PRECAUTIONS ON PRINTER INSTALLATION N WARNING M Do not use or store this product in a place where it will be exposed to Flames or moist air Direct sunlight Hot airflow or radiation from a heating device Salty air or corrosive gases Ill ventilated atmosphere Chemical reactions in a laboratory Airborne oil steel particles or dust Static electricity or strong magnetic fields Neglecting these warnings may result in printer failure overheating emission of smoke fire or electric shock E Do not drop any foreign object nor spill liquid into the printe
20. igital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian department of communications Pour L utilisateurs Canadiens Cet appareil num rique de la Classe A est conforme la norme NMB 003 du Canada Cet appareil num rique ne d passe pas les limites de car gorie a pour les missions de bruit radio manant d appareils num riques tel que pr vu dans les r glements sur l interf rence radio du d partment Canadien des communications GENERAL PRECAUTIONS Before using this product be sure to read through this manual After having read this manual keep it in a safe readily accessible place for future reference The information contained herein is subject to change without prior notice Reproduction or transfer of part or all of this document in any means is prohibited without permission from Citizen Systems Note that Citizen Systems is not responsible for any operation results regardless of omissions errors or misprints in this manual Note that Citizen Systems is not responsible for any trouble caused as result of using options or consumables that are not specified in this manual Except explained elsewhere in this manual do not attempt to service disassemble or repair this product Note that Citizen Systems is not responsible for any damage attributable to incorrect operation handling or imp
21. ipe off the sensor s protective sheet Make sure there are no water drops on the cotton swab before wiping Platen Print head Sensor s protective sheet N CAUTION B The print head is hot immediately after printing Do not touch it E Do not touch the print head with bare hands or metal objects B Do not use alcohol or cleansers to clean the surface of the sensor s protective sheet Doing so may fog the sensor s protective sheet B Paper scraps may stick to the platen when adhesive labels are full cut depending on the printer s environment the diameter of the paper roll and the quality of the label backing 29 4 2 Clearing a Cutter Lock 1 The ERROR LED flashes and the auto cutter blade remains extended because a foreign object or paper jam is obstructing it D POWER PAPER ERROR If the ERROR LED is flashing clear the locked cutter as shown below 1 Press the cover open lever while the power is on 2 Openthe paper cover 3 Remove any jammed paper including any scraps of paper Remove the paper roll that is loaded in the holder also 4 Reload the paper roll and close the paper cover N CAUTION B The print head is hot immediately after printing Do not touch it E Do not touch the print head with bare hands or metal objects If the paper cover does not open the auto cutter blade is still extended cutter lock Ei Refer to 4 3 Clea
22. ll 1 Turn off the power 2 Press the cover open lever 3 Open the paper cover 4 Set the partition in a slot that matches the size of the paper roll you are using However to use an 83 mm wide paper roll remove the partition 5 Refer to 5 3 Manual Setting of Memory Switches to change the paper width settings Partition O o T 0 H HARRAH Notes 1 2 inch type 58 60 mm 2 3 inch type 80 83 mm N CAUTION Make sure the partition is not slanted when setting it for 58 mm or 60 mm paper rolls 99 3 6 Setting the DIP Switch on the Serial interface Board Turn off the printer and unplug the power cord from the electric outlet Remove the mounting screws of the serial interface board Remove the serial interface board from the printer Set the DIP switch according to the following table 5 m Serial interface board mounting screws N CAUTION When setting the DIP switch do not remove any screws except the serial interface board mounting screws The function of each switch is shown below Shaded values are factory settings However factory settings differ depending on the destination market Switch no Function ON OR 3 Handshake LD Brenn 7bts O Parity check Ye 5 jPwyseesin Oddparty Refer t
23. not trip on it 3 2 Connecting Interface Cables 1 Turn off the power 2 Orient the interface cable correctly and insert it into the interface connector Parallel interface USB interface hub type USB interface Ethernet and Powered USB interfaces are available as options in addition to those listed here N CAUTION B Always unplug the AC adapter from the printer before connecting the printer to a Powered USB interface Failure to do so may damage the host PC For information about installing a Powered USB interface contact your Citizen Systems dealer E When disconnecting the cable always hold the connector B Be careful not to insert the USB interface cable into the cash drawer kick out connector B To connect more than one printer to a single computer via a USB interface you must change the serial number of the USB interface 18 Use a serial interface cable with the connection layout shown below 25 pin 25 pin cable 9 pin 25 pin cable PC Printer PC Printer N CAUTION Place the interface cable so people do not trip on it 3 3 Connecting the Cash Drawer 1 Turn off the power 2 Confirm the orientation of the cash drawer kick out cable connector and connect it to the cash drawer kick out connector at the back of the printer 3 Remove the screw for the ground wire 4 Screw the cash drawer s ground wire to the body of the printer Cash drawer kick out connector X
24. ny heating device e Neglecting these cautions may cause wires or insulation to break which could result in electric leakage electric shock or printer failure If the power cord sustains damage contact your Citizen Systems dealer M Do not leave things around the electric outlet Supply power to the printer from a convenient electric outlet readily accessible in an emergency Pull the plug to immediately shut it down in an emergency Insert the power plug fully into the outlet B f the printer will not be used for a long time disconnect it from its electric outlet B Hold the plug and connector when plugging or unplugging the power cord or signal cable after turning off the printer and the appliance connected to it N CAUTION Caution label is attached in the position shown in the following figure Carefully read the handling precautions before using the printer THIS LABEL INDICATES THE RISK OF BURNS DUE TO THE HIGH TEMPERATURE OF THE PRINT HEAD AND A RISK OF BEING CUT BY THE MANUAL AND AUTO CUTTERS WHILE THE PAPER COVER IS OPEN B Do not transport this printer with the paper roll inside e Printer failure or damage may occur To prevent possible malfunction or failure observe the following M Avoid operating the printer without paper properly loaded Avoid the use of paper not complying with specifications e May result in poor print quality
25. o table below Baud rate selection Baud rate bps When switch no 1 is set to OFF you can use a command or a memory switch to select 1200 38400 57600 or 115200 bps _ c 3 7 Adjusting the Paper Near end Sensor Change the settings of the paper near end sensor to set the position at which the near end of the paper is detected 1 Use a pointed object such as a pen to gently press the button to change the paper near end sensor 2 Press and hold down the button while moving the paper near end sensor up down right and left The sensor positions are shown below for the various diameters of the paper roll used Unit mm Diameter when detected as near end Diameter of core of paper roll used C Paper near end sensor function is off Note Position of sensor when shipped from factory However factory settings differ depending on the destination market N CAUTION B The amount of paper remaining on the roll diameter of the roll depends on the type of paper used B The paper roll diameters in the table are guidelines Button to change paper near end sensor A and B are for horizontal installations and a and b are for vertical or wall installations 24 3 8 Setting Paper Thickness Set the paper thickness selection lever to the thickness of the paper Thick paper can only be used with the label printing model To get the best print quality do not change the fa
26. ocedure to enter individual setting mode Press the FEED button until Save To Memory is printed Open the paper cover Press the FEED button for at least two seconds All memory switches change to the factory settings Close the paper cover 40 The function of each memory switch is shown in the following table Shaded values are factory settings Pater OFF ON O Mswre Reewd Mswi hl vaa MSwi8 Sims hel Vaid EIE EL swat eene MSWzs Spool Print MSwzs ReumeskPE J N84 777 MSwze Reewd Fed Mw Reewd mea msws2 PesignalbyPNE Im MSws4 Reewd Fed MSwss Reewd MSwse Reewd mea msws7 CBMi00Mode maia Vei NC OOO O swat eene Weu Reserved eene Pe Resewd Dusas Reene eil MSWa Resewd mi 7 J ven ven 17360 1408 Venue Reseved 77 OO mswss Reseved bel Venez Reseved Fed msws7 Reseved bel MSWe8 Reeve mea swe A Forbrver RT Vaid ChaaderSpas Invalid vaia MSwes Reewd ed MSWes Reserved eil MSWes Resewed mea MSwee Reewd mea E Reserved ee Reserved Sept Feier ia setting Setting value
27. open lever 94 N CAUTION M Before starting to do maintenance work be sure to turn off the printer and unplug the power cord from the electric outlet Bi Be careful not to touch the manual cutter while the front cover is open Be careful not to touch the opening for the auto cutter while the paper cover is open B The print head is hot immediately after printing Do not touch it E Do not touch the print head with bare hands or metal objects If the above procedure does not retract the auto cutter contact your Citizen Systems dealer 4 4 Self printing While paper is loaded press and hold the FEED button while turning the power on Hold the FEED button down for about one second and then release it to start self printing The printer prints its model name version DIP switch settings memory switch settings and a list of built in fonts CT 59601 DLOO XXXX AURA KKK PROG BOT XXX XXX FPGA TTF XXX XXX FONT ANK XXX XXX Memory switches SW1 12 3 4 5 Firmware version oO 9D Interface Type USB or Serial Interface Memory Serial Interface f switch Bald tate MODUS CEDE Serial communication actin Data bit 8 bits status g Parity None USB or Serial interface models only Buffer size Handshaking DTR DSR Buffer Size 4K Bytes Dip switches DS1 DIP switch settings 123245878 USB or Serial interface ON models only OFF O000000 0 Note
28. per cover to close it securely Bi Be careful of paper cuts while loading the paper B Do not touch the print head manual cutter or auto cutter while the paper cover is open Doing so may cause a burn or cut 96 3 10 Attaching the Power Switch Cover Attach this cover to prevent the power switch from being used 1 Press the power switch cover onto the power switch compartment until it clicks Power switch cover Put a screwdriver or other pointed object into the grooves on the power switch cover to remove it OF 3 11 Attaching the Interface Cover Attach the interface cover to the back of the printer The shape of the interface cover is different depending on the type of power source 1 Press the interface cover as shown in the diagram until you hear it click CT S601S CT S601S a E 4 MAINTENANCE AND TROUBLESHOOTING A dirty print head or platen may reduce printing quality or cause malfunctions Also if paper dust collects on the sensor s protective sheet paper cannot be detected correctly We recommend cleaning the printer periodically every 2 to 3 months as shown below 1 Turn off the power 2 Press the cover open lever 3 Open the paper cover Wait a few minutes until the print head cools 4 Useacotton swab dampened with ethyl alcohol to wipe off any dirt and dust that is on the print head and platen 5 Useacotton swab dampened with a little water to w
29. r Do not place any object on the printer either B Do not drop any metallic object such as paper clips pins or screws into the printer B Do not place a flower vase pot or anything containing water on the printer E Do not spill coffee soft drinks or any other liquid into the printer E Do not spray insecticide or any other chemical liquid over the printer Dropping a metallic foreign object into the printer may cause printer failure fire or electric shock Should it occur immediately turn the printer off unplug it from the supply outlet and call your local Citizen Systems dealer Do not handle the printer in the following ways B Do not subject the printer to strong impacts or hard jolts e g being stepped on dropped or struck Never attempt to disassemble or modify the printer Neglecting to handle properly may result in printer failure overheating emission of smoke fire or electric shock B install use or store the printer out of the reach of children e Electric appliances could cause an unexpected injury or accident if they are handled or used improperly Keep the power cord and signal cables out of the reach of children Also children should not be allowed to gain access to any internal part of the printer The plastic bag the printer came in must be disposed of properly or kept away from children Wearing it over the head may lead to suffocation CAUTION Do not use the printer under the
30. r defined characters and logos Bar code types UPC A E JAN EAN 13 8 columns ITF CODE39 CODE128 CODABAR NW 7 CODE93 PDF417 OR Code 4 25 mm 1 6 inch changeable using commands Paper roll Paper roll 83 mm 80 mm 60 mm 58 mm x maximum 83 mm Paper thickness 65 75 um core tube diameter inner 12 mm outer 18 mm 75 85 um core tube diameter inner 25 4 mm outer 32 mm Interface Serial RS 232C compliant parallel IEEE 1284 compliant USB USB with hub Ethernet Powered USB Supports 2 cash drawers 4 bytes 45 bytes DC 24 V 35 Approximately 45 W normal printing 3 W standby AC adapter 4 Rated input AC 100 to 240 V 50 60 Hz 150 VA 36AD2 36AD3 Rated output DC 24 V 2 1A ight CT S601S Approx 2 kg CT S601A Approx 1 6 kg CT S601S 145 W x 192 D x 148 H mm CT S601A 145 W x 192 D x 120 H mm e Operating temperature 5 to 45 C 10 to 9096 RH no condensation and humidity Storage temperature 20 to 60 C 10 to 9096 RH no condensation and humidity Reliability Print head life 150 km 200 million pulses at normal temperature and humidity using recommended paper Auto cutter life 2 million cuts at normal temperature humidity using recommended paper and paper thickness Safety standard 5 UL C UL FCC Class A TUV Bauart CE Marking Notes 1 When paper width is 83 80 60 or 58 mm 2 The number of printable columns is selected using a memory switch The numbe
31. r of columns noted in this table refer to typical models The number of columns varies depending on specifications 3 Characters appear small because the dimensions include a blank area surrounding each character 4 The 36AD2 is the AC adapter packaged as an accessory with the CT S601A The 36AD3 is the AC adapter built in to the CT S601S 5 Compliant if the Citizen Systems AC adapter 36AD2 36AD3 is used 2 EXPLANATION OF PRINTER PARTS 2 1 Printer Appearance Names of parts Paper cover Cover open lever Operation panel Front cover Power switch Front cover Maintenance cover release button Front view Rear view Paper cover Open to load paper Cover open lever Use this lever to open the paper cover Front cover Open and close this cover to clear a cutter lock T Refer to 4 3 Clearing a Cutter Lock 2 Front cover release button Press this button to open the front cover eoo Power switch Press this button to turn the power on or off e Maintenance cover Not applicable for this product N CAUTION Do not open the maintenance cover Operation panel PAPER LED POWER LED green orange ERROR LED red la N POWER PAPER ERROR E FEED button POWER LED green Lights when the power is on turns off when the power is off Flashes when data is incoming or a memory error has occurred PAPER LED orange Lights orange when paper is
32. r to the Command Reference Quick setting mode The settings for the memory switches for a replacement printer s manufacturer model paper width and character spacing can be set at the same time to the optimum settings Do the settings while confirming the selected items on the printout 1 Load paper 2 While the paper cover is open press and hold the FEED button while turning the power on 3 Press the FEED button three times and close the paper cover The printer enters memory switch quick setting mode The selectable item Manufacturer and the selection are printed Manufacturer CITIZEN Selection Selectable item 4 Press the FEED button A selection is printed in order through the cycle each time the FEED button is pressed Press the FEED button until the selection you want is printed 5 Press the FEED button for at least two seconds The selection is set If there is another selectable item it and the selection are printed 6 Repeat steps 4 and 5 to select and set the printer s model paper width character spacing EPSON T88 only When all the items are set Save To Memory is printed 7 Press the FEED button for at least two seconds The changed memory switch settings are saved and a list of them is printed The printer exits quick setting mode when printing is finished Selected item Automatic memory switch settings Paver Character MSW2 4 MSW3 7 MSW8 1 MSW6 2 Mie See Full Col CBM100
33. ring a Cutter Lock 2 4 3 Clearing a Cutter Lock 2 The paper cover is designed to be opened if the cutter locks by pressing the cover open lever If this does not open the paper cover use the following procedure to clear the locked cutter 1 Turn off the printer and unplug the power cord from the electric outlet 2 Press the front cover release button with a pointed object such as a pen and open the front cover in the direction of arrow A Slide the front cover 3 to 4 mm in the direction of arrow A and rotate it forward 3 Lift the protective sheet and turn the cutter gear in the direction of arrow B to return the auto cutter to a position where the paper cover can be opened Turn the cutter gear until the auto cutter blade retracts in the direction of arrow C If the blade of the auto cutter does not move when you turn the cutter gear in the direction of arrow B turn it in the other direction 4 Press the cover open lever 5 Open the paper cover 6 Remove whatever caused the cutter to lock 7 Close the front cover Rotate the front cover in the opposite direction of arrow A and then slide it until it clicks 8 Load a paper roll and close the paper cover 9 Insert the power cord plug into an electric outlet and turn the power on Check that the POWER LED lights Protective sheet Paper cover Auto cutter blade Cutter gear Front cover release button Front cover Cover
34. roper operating environments that are not specified in this manual Data is basically for temporary use and not stored for an extended period of time or permanently Please note that Citizen Systems is not responsible for damage or lost profit resulting from the loss of data caused by accidents repairs tests or other occurrences f you find omissions errors or have questions please contact your Citizen Systems dealer f you find any pages missing or out of order contact your Citizen Systems dealer for a replacement CITIZEN is a registered trade mark of Citizen Holdings Co Japan CITIZEN es una marca registrada de Citizen Holdings Co Jap n Company names and product names in this manual are trademarks or registered trademarks of relevant companies Copyright 2009 by CITIZEN SYSTEMS JAPAN CO LTD E SAFETY PRECAUTIONS WHICH SHOULD BE STRICTLY OBSERVED Before using this product for the first time carefully read these SAFETY PRECAUTIONS Improper handling may result in accidents fire electric shock or injury In order to prevent injury to operators third parties or damage to property special warning symbols are used in the User s Manual to indicate important items to be strictly observed After having read this Manual keep it in a safe readily accessible place for future reference Some of the descriptions contained in this manual may not be relevant to some printer models The followin
35. rve the following precautions for daily maintenance B When cleaning the printer always turn it off and unplug it from the electric outlet M Use a soft dry cloth for cleaning the surface of the printer case For severe stains use a soft cloth slightly dampened with water Never use organic cleaning solvent such as alcohol paint thinner trichloroethylene benzene or ketone Never use a chemically processed cleaning cloth B To remove paper dust use a soft brush N CAUTION e The thermal head is at a dangerously high temperature immediately after printing Allow it to cool off before starting maintenance work Visit the following site to get documentation drivers utilities and other information http www citizen systems co jp english support index html THE TABLE OF CONTENTS 1 GENERAL OUTLINE el e rcc e s 9 IST vv adole nad berx deu bres fa Cad Pu eM Ia 9 BB rere dino EE 10 13 Model ClaSSWICQUOM EE 10 124 BASIC SD SCINICA TIONS EEN 11 2 EXPLANATION OF PRINTER PARTS 12 2 1 Printer AD PCaraniCe EE 12 2 2 Inside the paper cover 15 2 3 Other Built in Functions s kas as uso Yeu eege 16 MES R I e D dS 17 3 1 Connecting the AC Power 17 3 2 Connecting Interface Cables 18 3 3 Connecting the Cash Drawer aa 19 3 4 Pre
36. s near the end of the roll Adjust the position of the sensor to determine when it detects the end of the paper is near Button to change paper near end sensor Change the position of the paper near end sensor to match the paper being used Refer 3 7 Adjusting the Paper Near end Sensor e Manual cutter For cutting the paper manually when printing is finished Auto cutter Automatically cuts the paper when printing is finished Cm Refer to 5 3 Manual Setting of Memory Switches Print head thermal Prints characters and graphic data on paper paper rolls Paper end sensor PE sensor Detects when there is no paper Printing stops when this sensor detects there Is no paper 15 Paper thickness selection lever Use this lever to select regular or thick paper according to the thickness of the paper being loaded N CAUTION Do not change the position of the paper thickness selection lever from the factory setting Cm Refer to 3 8 Setting Paper Thickness 2 3 Other Built in Functions e Buzzer Buzzes when errors occur or when operations or command operations are performed gt Refer to 4 6 Error Messages User memory You can save user defined logo and character data in this memory Data remains stored in this memory even if the printer is turned off For information on how to save data refer to the Command Reference e Memory switch Setting of various kinds of functions can
37. witch you want to change is printed 39 10 Press the FEED button until Save To Memory is printed 12 Press the FEED button for at least two seconds A setting for the memory switch is printed through the cycle each time the FEED button is pressed for at least two seconds Press the FEED button for at least two seconds to cycle through the list until the function of the memory switch you want to change is printed Power ON Info Valid Current setting Memory switch function Press the FEED button A setting is printed each time the FEED button is pressed in order through the cycle When the current settings are printed the ERROR LED lights Press the FEED button until the setting you want is printed Press the FEED button for at least two seconds The selected settings are set The next memory switch function and settings are printed Repeat steps 5 to 7 to change different functions for the current memory switch number Open the paper cover and close it The changed memory switch settings are printed Repeat steps 4 to 9 to change functions for a different memory switch number Press the FEED button for at least two seconds The changed memory switch settings are saved and a list of them is printed The printer exits individual setting mode when printing is finished Memory switch initialization Set all the memory switches to the factory settings m e Do steps 1 through 3 of the pr
38. y DC No power source S Built in power supply type A AC adapter type Paper width 3 3inch 80 83 mm 2 2inch 58 60 mm Interface PA Parallel RS Serial RS 232C UB USB only UH USB with hub ET Ethernet standard type ES Ethernet multi function type UP Powered USB Note Market J Japanese 56015 3 RS E BK PLM1 EL BM sensor No Label M1 Left side No M2 Right L Label printing side PNE sensor No P PNE sensor Body case color WH Cool white BK Black E Europe Asia U North America C China AC power cord serial I F screw firmware and other specifications vary according to markets 10 1 4 Basic Specifications trem Specifications CT S601 Line thermal dot print method Print width 1 80 mm 640 dots 72 mm 576 dots 64 mm 512 dots 54 5 mm 436 dots 54 mm 432 dots 52 5 mm 420 dots 48 mm 384 dots 45 mm 360 dots 48 75 mm 390 dots 68 25 mm 546 dots 8 8 dotsimm 208 dpi 200 mm s fastest print density 100 1600 dot lines s Number of print Maximum number of characters columns 2 columns Dot configuration Paper width 83 mm 80mm 60mm 58 Font A FB n amp 4 4 Foc 8 7 9 52 Character size 3 Font A 1 50 x 3 00 mm Font B 1 13 x 2 13 mm Font C 1 00 x 2 00 mm Character type Alphanumeric international PC437 850 852 857 858 860 863 864 865 866 WPC1252 katakana Thai code 18 384 KB capable of storing use
39. ymi odpadkami Wedtug dyrektywy WEEE Dyrektywa 2002 96 EC obowiazujacej w Unii Europejskiej dla uzywanych produkt w elektronicznych nalezy stosowac oddzielne sposoby utylizacji Declaration of Conformity This printer conforms to the following Standards The Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2002 95 EC and the WEEE Directive 2002 96 EC LVD EN60950 1 EMC EN55022 Class A EN61000 3 2 EN61000 3 3 EN55024 This declaration applies only to the 230 V model IMPORTANT This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference CAUTION Use shielded cable for this equipment Sicherheitshinweis Die Steckdose zum Anschlu dieses Druckers nahe dem Ger t angebracht und leicht zuganglich sein For Uses in Canada This Class A digital apparatus complies with Canadian ICES 003 This d
Download Pdf Manuals
Related Search