CHIEF truss tilt adjustable mount User's Manual
Contents
1. Ajustar Regolare Afstellen Ajuster By Hand A mano Von Hand Com a mao A mano Met de hand A la main Optional Opcional Optional Opcional Opzionale Optie En option d 2 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Hammer Martillo Hammer Martelo Martello Hamer Res D 00 9 Marteau Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl a fourche Installation Instructions TPP Series TOOLS REQUIRED FOR INSTALLATION 2 7 16 7 16 5 32 9 16 9 16 included REQUIRED PARTS NOT INCLUDED TPK 3 o Truss Pole Kit example or TPK 4 p el X 8 Backplate B 1 PSB Interface bracket kit example 1 5 32 TPP Series Installation Instructions INSTALLATION WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It2. DIMENSIONS TOP MOUNTING BUTTON ON PSB XXXX DRAWING GOES HERE e 8 00 NOTE CUSTOM INTERFACE BRACKET NOT SHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN1 2 AND 2 IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT FACE TILTS 5 UP ek 90 15 DOWN i Q ATTACHES TO POLE TRUSS USING SERIES CLAMPS NOT INCLUDED APPROXIMATE CENTER OF DISPLAY DIMENSIONS INCHES TPP Series Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Measure Medir Messen Medir Misurare Meten Mesurer Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou y Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen
3. Backplate Hex head screws o Figure 4 4 Securely anchor TPP assembly to horizontal poles using Chief TPK accessory clamps not included following instructions included with TPK kit See Figure 5 Horizontal Installation o TPR clamps x 4 provided d Figure 5 5 Proceed to Display Installation section Vertical Installation The TPP assembly ships configured for vertical pole mounting 1 Securely anchor TPP backplate to vertical poles using Chief TPK accessory clamps not included following instructions included with TPK kit See Figure TPK clamps x4 not included Note Faceplate and tilt adjustable plate not shown for clarity Figure 6 Display Installation IMPORTANT Make sure no power is supplied to the display and the latching flag on the TPP is in the unlocked position before attempting to attach the display See Figure 7 Locked Unlocked Figure 7 WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the TPP
4. does not exceed 150 Ibs 68 04 kg TPP Series Installation Instructions 1 Attach PSB interface bracket to display using the instructions included with the PSB package 2 Using two people slide display with attached interface bracket B down over the four slots in the faceplate of the TPP A Make sure all four mounting buttons engage all four Q Latch slots in the TPP A See Figure 8 Latching flag on other side gt Display Q Latch slots x 4 Figure 8 3 With the mounting buttons of the display fully engaged in the slots of the TPP A secure the display on the TPP by raising the flag all the way up to the locked position See Figure 9 Display Mounting buttons in slots x 4 Figure 9 4 Ifthe flag does not fully engage remove the display and make sure all four mounting buttons are fully engaged in slots NOTE A security lock may be installed through the hole in the Q Latch flag for added security See Optional Security Lock section Tilt Adjustment WARNING IMPROPER HANDLING CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate support of display while adjusting tilt may cause display to fall Watch for pinch points Do not put your fingers between movable parts 1 Loosen tilt adjustment screws adjust to d
5. INSTALLATION INSTRUCTIONS Truss Tilt Adjustable Mount CHIEF TPP Series Our Mounts Your Vision TPP Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factor
6. RS
7. esired tilt up to 15 and tighten tilt adjustment screws See Figure 10 Note Interface bracket display trusses not shown for clarity Figure 10 Installation Instructions TPP Series Optional Locking Angle Tilt Holes The TPP can be tilted up to 15 degrees and features three holes used to set specific tilt 0 5 and 10 1 Loosen tilt adjustment screws adjust to desired tilt and tighten tilt adjustment screws See Figure 11 2 Install 1 4 fastener Grade 2 or better not provided into desired degree tilt hole See Figure 11 e 0 outside hole 5 middle hole e 10 inside hole DO 2 Tilt adjustment screws D za Ll 0 tilt hole 5 tilt hole Aa IL Ly 10 tilt hole Figure 11 Removing the Display 1 WARNING IMPROPER HANDLING CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate support of display while removing it may cause display to fall Watch for pinch points Do not put your fingers between movable parts WARNING Ensure Q Latch flag securing display is completely raised at all times except when removing or installing display The flag must be all the way up when installing or remov
8. ing cables With display securely supported unlock display from TPP A by lowering the flag all the way down to the unlocked position See Figure 12 Locked Unlocked 2 Figure 12 Using two people slide display up and out of TPP A See Figure 13 Q Latch slots x 4 Figure 13 TPP Series Installation Instructions Optional Security Lock A hole is provided in the Q Latch flag and faceplate to accommodate the insertion of a padlock not included or similar locking device 1 Insert padlock through lower hole Q Latch flag and face plate See Figure 14 Locked Faceplate Figure 14 10 Installation Instructions TPP Series 11 TPP Series Installation Instructions USA International Our Mounts Your Vision paia Europe Chief a products division of Milestone AV Technologies 8800 002566 Rev00 Asia Pacific 2014 Milestone AV Technologies www chiefmfg com 04 14 gt 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 42 852 2145 4477 f 9 CONSUME
9. is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The TPP assembly ships configured for vertical pole mounting The TPP can be reconfigured to attach to horizontal pipes Vertical Default Configuration Faceplate Tilt adjustable plate assembly Backplate Figure 1 To change the TPP for horizontal pole mounting proceed to Horizontal Installation section To use the TPP in the vertical configuration proceed to Vertical Installation section Horizontal Installation 1 Detach backplate from tilt adjustable plate faceplate assembly by removing the four hex head cap screws See Figure 2 02 aa Hex head SQ Sees x 4 Faceplate Tilt adjustable plate Backplate Figure 2 2 Rotate the backplate 90 Na agg 9 all J S 4 Sy N NU Figure 3 Installation Instructions TPP Series 3 Re attach backplate to tilt adjustable plate faceplate assembly using the four hex head cap screws inserted from inside the tilt adjustment plate See Figure 4 Horizontal Configuration x
10. y warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the TPP does not exceed 150 Ibs 68 04 kg e weight capacity of the TPP may be LIMITED to the lowest weight capacity of any other component or accessory used within the mounting system WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The TPP mount is designed for installation to a variety of pipe truss dimensions and can span a distance of up to 14 SAVE THESE INSTRUCTIONS Installation Instructions TPP Series
Download Pdf Manuals
Related Search