CHIEF MP3 User's Manual
Contents
1. C 6 cable ties ASSEMBLY AND INSTALLATION NOTE The iPod docks NAID1B NAID4B are designed for I NAID1B shown use with 19 wide equipment racks See the specific A installation instructions provided with the rack for 30 pin connector additional installation information 1 Attach the dock A within the rack using four 10 32 x 3 4 header point Phillips screws not included See Figure 1 BUZZ lo 6 oo o oro 6 oro oro ss 55 855 8555 Ga oro o oro 0 0 0 TELEL NE1F2023 rack shown with NAID1B Figure 1 NOTE Push iPod dock drawer IN to both open and close drawer 2 Plug iPod into 30 pin connector in dock A See Figure 2 3 Plug cables into appropriate connection point See Figure 2 NOTE The iPod may be charged through the USB jack on back of dock or by using the USB power supply and adapter B for iPod Rear view A Audio out jack q a ID El l USB jack 3 Video out jack Rear view Figure 2 4 Fully extend drawer and leave it open See Figure 2 5 Use cable tie loops C as desired for strain relief and to manage cables See Figure 2 IMPORTANT If cables are tied down while the drawer is shut cables may be disconnected or damaged when drawer is opened Make sure d2. USA International Europe Asia Pacific gt TI gt TI gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 I al 2 O S Yr consume
3. INSTALLATION INSTRUCTIONS NAID1B NAID4B IPod Dock Our Mounts Your Vision NAID1B NAID4B Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follovv the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsi
4. bility to make sure all components are properly assembled and installed using the instructions provided WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair A WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS NAID1B NAIDIB COMES WITH A GLOBAL USB 5V POWER SUPPLY amp IPOD DOCK WITH REMOTE 6 83 LL J 173 6 1204 i 19 01 SS LL AL I a A 285 gt 724 YE Me ji 44 5 o o 443 112 6 NAID4B NAID4B COMES WITH A GLOBAL USB SV POWER SUPPLY 8 POD DOCK WITH REMOTE aa 1204 71 iol o 19 00 E 482 6 S 4 55 72 4 T msg TT i El 442L e 2 112 6 1 00 4 87 dia ji CD DIMENSIONS INCHES MILLIMETERS Installation Instructions NAID1B NAID4B TOOLS HARDVVARE PARTS EE EM lover se am 4 10 32 x 3 4 header point Phillips screws not included vs B 1 USB power supply amp US adapter cables and remote control
5. rawer is fully extended when securing cables in order to provide a proper length and unhindered operation 6 Close drawer and complete the installation following the rack installation instructions NAID1B NAID4B Installation Instructions Installing an IR Emitter Optional NOTE For a discrete clean look a space was designed in front of the dock yet behind the IR window to allow for a third party IR emitter to be installed Emitter wire may be routed along the side and out the back 1 With drawer closed remove iPod dock from drawer See Figure 3 NAID1B shown Figure 3 2 Open drawer and install IR Emitter not included to front of drawer or on front of iPod dock sensor as per IR Emitter s manufacturer s instructions See Figure 4 3 Use cable ties C as desired to manage IR Emitter cable See Figure 4 NAID1B shown B IR emitter not included Figure 4 4 Close drawer and reinstall iPod dock to drawer See Figure 5 NAID1B shown Figure 5 Installation Instructions NAID1B NAID4B NAID1B NAID4B Installation Instructions Installation Instructions NAID1B NAID4B NAID1B NAID4B Installation Instructions GCHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002206 Rev00 2012 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 09 12
Download Pdf Manuals
Related Search