Chief Manufacturing FSD-4100 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS FSD 4100 LCD Flat Screen swing Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit The LCD Flat Screen Swing Down mount is a sturdy versatile solution for LCD flat screen display or touch screen control system mounting with 15 or smaller monitors The all steel mount provides smooth side to side pivot 70 or 220 screen rotation and extends and retracts 2 3 4 to allow for larger screen capacity Hidden cable management permits aes thetic installation while preventing wires from being pinched BEFORE YOU BEGIN e Caution To prevent damage to the mount which could affect the equipment that will be attached to it and void the factory warranty thoroughly study all instructions and illustrations before you begin the installa tion Pay particular attention to the Important Warnings and Precautions on Page 1 e The mount is designed to be installed on cabinetry or supporting framework The cabinet to which the FSD 4100 is anchored must be capable of supporting 75 pounds 34 Kg e If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 CHIEF MANUFACTURING INC 8832 000010 Rev C 1 800 582 6480 952 894 6280 FAX 952 894 6918 2007 Chief Manufacturing 8401 EAGLE CREEK PARKWAY www chiefmfg com SAVAGE MINNESOTA 55378 USA 04 07 Installation Instructions FSD 4100 TTT PRECAUTIONS WARNING A WARNI2. NOTE Numbers in refer to parts in PARTS on page 4 1 Remove two screws securing base cover 10A and remove cover see Figure 1 2 Determine the exact mounting location prior to installation considering the unit s total arm radius 3 Using the mounting plate as a template mark mounting hole locations see Figure 2 4 Drill three 1 4 holes at the locations marked in step 3 WARNING Improper installation can result in serious dam age to the display or personal injury Make sure that the structural members can support a redun dant weight factor five times the total weight of the equipment If not reinforce the structure before installing the FSD 4100 5 With the FSD 4100 correctly oriented and level secure it to the surface using fasteners 20 and 30 6 Check mount to insure it is level and adjust to level if neces sary MOUNT THE DISPLAY 1 Make sure no power is supplied to the display before attempt ing to mount the display WARNING Watch for pinch points Do not put your fingers or cables between movable parts 2 Align the appropriate slots in the bracket with the four mount ing holes of your LCD display see Figure 3 WARNING Make sure the mounting screws used to secure your display panel to the mounting bracket are the proper length and diameter If you are unsure about screw length and or diameter consult the display manufacturer before proceeding 3 Using the proper length and dia
3. NOTE Other tools may be required depending on the method of installing the mount CONTENTS ee hetke D RAN ee o dl EET EE VENC E E DES TL ee EEES LEC aemiceesemmDnteumateen es dd NOU EE CS prain e lt 2 DES LOE US saaa a aa meteo A LE elses OM Nan Oe EO toma d Installation Instructions FSD 4100 DIMENSIONAL DRAW IN G 4 4 D a Ua Aa ES Ren T T f f fb m e ta pA L SNL Installation Instructions FSD 4100 INSPECT TRE UNIT BEFORE INSTALLING WARNING Watch for pinch points Do not put your fingers between movable parts 1 Carefully inspect the FSD 4100 for shipping damage If any damage is apparent call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage NOTE Read all instructions before starting installation 2 Lay out components to ensure you have all the required parts before proceeding see DIMENSIONAL DRAWING on page 2 and PARTS on page 4 Installation Instructions FSD 4100 PARTS 10 Mount 10A Base Cover Mow a Beco a m o e Sows oax s AD Allen Wieneh S32 a E 10 10A 10B Installation Instructions FSD 4100 FSD 4100 INSTALLA TION VVARNING Itis the responsibility of the installer to verify that the surface to which the FSD 4100 is anchored will safety support the combined load of all attached components and equipment Install the FSD 4100 as follows
4. base cover 10A on base and secure using two screws see Figure 10 35 Degree Stop Figure 11 Remove 35 Degree Stop 110 Degrees Figure 13 Wrap Cables In Base Installation Instructions FSD 4100 Check Rotation 1 Rotate screen in one direction until it reaches its stop see Fig ure 14 2 If there is any binding or pinching correct problem 3 Rotate screen in the opposite direction until it reaches its stop see Figure 15 4 If there is any binding or pinching correct problem 5 If your cables do not allow you to reach the 110 degree limit reinstall the 35 degree limitation screw Figure 14 Rotate In One Direction Figure 15 Rotate In Opposite Direction 10
5. NG alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre sponding instructions e WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can sup port a redundant weight factor five times the total weight of the equipment If not reinforce the structure before installing the FSD 4100 e WARNING Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted e WARNING The installer is responsible for verifying that the surface to which the FSD 4100 is anchored will safely support the combined load of all attached components or other equipment e WARNING The weight of the display placed on the FSD 4100 must not exceed 15 Ibs 6 8 kg the maximum load capacity of the FSD 4100 e WARNING Watch for pinch points Do not put your fingers between movable parts e WARNING Make sure the mount and brackets are correctly oriented e CAUTION Check the unit for shipping damage before you begin the installation e CAUTION Overtightening adjustment bolt will cause excessive wear and may distort adjustment components NOTE Hardware for attaching this unit to the mounting surface is not supplied EUU eS RE DL DA RE E ES DE EL e Phillips screw driver e Electric drill motor e 1 4 Drill bit
6. lot in the bot tom of the arm see Figure 8 4 Secure the power audio video cables using tie wraps 5 Proceed to Right and Left 35 Degree Rotation on page 8 or Right and Left 110 Degree Rotation on page 9 depending upon your application Figure 8 Route amp Tie Wrap Cables Arm Installation Instructions FSD 4100 Right and Left 35 Degree Rotation L Turn the base 35 degrees in one direction to its stop see Figure 9 Neatly and carefully route the power audio video cables through the slot in the side of the base Secure the power audio video cables using a tie wrap 70 Trim excess from tie wrap Install cable cover 10B on arm and secure using screw see Figure 10 Install base cover 10A on base and secure using two screws see Figure 10 35 Degrees Stop Figure 10 Install Base and Cable Covers Installation Instructions FSD 4100 Right and Left 110 Degree Rotation L NS A E Using an Allen wrench provided remove the 35 degree stop see Figure 11 Turn the base 110 degrees in one direction to its stop see Figure 12 Neatly and carefully wrap power audio video cables twice inside base with no slop or slack in cables see Figure 13 Route power audio video cables out access hole in base Secure cables to base using a tie wrap 70 Trim excess from tie wrap Install cable cover 10B on arm and secure using screw see Figure 10 Install
7. meter screws 40 or 50 and spacers 60 as necessary secure your display to the mount NOTE If your display is not equippedwith 75 mm or 100mm mounting pattern contact Chief Manufacturing to check for an adapter plate for your display model Screws yew OF Figure 3 Secure Display Installation Instructions FSD 4100 ADJUSTMENTS Screen Height Adjustment 1 Using a screw driver slightly loosen the screws 40 or 50 securing the display panel to the mounting bracket see Figure 4 2 Adjust the display panel to the desired height PERR 3 Screws 3 Using a screw driver tighten the screws securing the dis Securing play panel to the mounting bracket Monitor Arm Tension Adjustment CAUTION Overtightening adjustment bolt will cause exces sive wear and may distort adjustment components 1 Using a 5 32 Allen wrench 80 slightly tighten or loosen the tension adjustment bolt at the base of the arm see Figure 5 2 With display mounted cycle the FSD to check for desired Figure 4 Loosen Tighten Screws tension Securing Monitor 3 Repeat Step 1 and Step 2 until desired tension is obtained Tension Adjustment Bolt Figure 5 Adjust Arm Tension Installation Instructions FSD 4100 CABLE MANAGEMENT 1 Remove screw and cable management cover 10B see Figure 6 2 Route the power audio video cables down the arm see Figure 7 3 Route the power audio video cables through the s
Download Pdf Manuals
Related Search