Chauvet 38c User's Manual
Contents
1. A To avoid signal transmission problems and interference it is always advisable to connect a DMX signal terminator Do not allow contact between the common and the fixture s chassis ground Grounding the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other Fixture Linking 5 Appendix You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run synchronized shows on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support Fixtures on a serial data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 32 fixtures should be connected on one data link Connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal Maximum recommended serial data link distance 500 m 1640 ft Maximum recommended number of fixtures on a serial data link 32 13 4 19 2010 1 08 PM 3 Pin to 5 Pin Conversion Chart If you use a controller with a 5 pin DMX output connector you will need to use a 5 pin to 3 pin adapter The chart below details a prope2. THERMAL Maximum ambient temperature oocccconcococococococnconacoconacoconacononncononarnnonnrnnonnrnronaranenananos 104 F 40 C ORDERING INFORMATION LEDAN SOG airn A aa LEDRAIN38C WARRANTY INFORMATION W AA osana N meunceneee ea enced eae emaen 2 year limited warranty Technical Specifications 17 4 19 2010 1 08 PM
3. and blue These are accessed via the DIP switches on the back of the fixture Each of the 3 colors may be mixed with different intensities Please see the chart below for further explanation Mode DIP switches Master Static 8 9 10 On Static Red 1 2 On Static Green 3 4 On Static Blue 5 6 On Fixture Linking In order to use this fixture in a DMX or master slave operation you must daisy chain using DMX cables to link from one fixture to another 7 S 7 S la P Additional signal link out 0 YATIONLNOO 05 XWA 5 Appendix 10 4 19 2010 1 08 PM DMX Channel Values 7 CH Mode CHANNEL VALUE FUNCTION 4 Red 000 lt gt 255 Dimmer 0 100 9 Green 000 gt 255 Dimmer 0 100 3 Blue 000 lt gt 255 Dimmer 0 100 No Function Color Macros Speed CH 6 values 32 223 000 gt 255 Slow Fast Strobe RGB amp Macro only No Function Slow Fast Mode RGB mode Pulse effect 0 100 using RGB faders Pulse effect 100 0 using RGB faders 6 Pulse effect 100 0 100 using RGB faders Auto fade transition Auto snap transition 3 colors Auto snap transition 7 colors Sound triggering mode Dimmer 000 gt 255 Intensity RGB Macro modes 0 100 3 CH Mode CHANNEL V
4. carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Manual Conventions CHAUVET manuals use the following conventions to differentiate certain types of information from the regular text CONVENTION MEANING 10 A DIP switch to be configured lt Menu gt A key to be pressed on the fixture s control panel 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified for example showing the operating mode current status MENU gt Settings A sequence of menu options to be followed ON Icons A value to be entered or selected This manual uses the following icons to indicate information that requires special attention on the part of the user ICONS MEANING This paragraph contains critical installation configuration or operation information Failure to comply with this information may render the fixture partially or completely inoperative cause damage to the fixture or cause harm to the user This parag
5. than this In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Never connect the device to a dimmer pack Make sure the power cord is never crimped or damaged Never disconnect the power cord by pulling or tugging on the cord Never carry the fixture directly from the cord Always use the hanging mounting bracket Avoid direct eye exposure to the light source while it is on 4 4 19 2010 1 08 PM 2 INTRODUCTION Features e 3or 7 channel DMX 512 LED PAR can e Operating modes 3 channel RGB control 7 channel RGB macros run strobe speed automatic sound dimmer Static colors and RGB color mixing with or without DMX controller Built in automated programs via master slave or DMX with variable speed Built in sound activated programs via master slave or DMX Pulse effect with adjustable speed Additional Features e Additional power output max 37 units e Double bracket yoke doubles as floor stand Product Overview DIP Switches DMX Out DMX In Microphon 2 Introduction 5 Power In Power Out Fuseholder Microphone Sensitivity Adjustment Knob 4 19 2010 1 08 PM 3 SETUP AC Power A A This fixture runs on 100 240 VAC 50 60 Hz Before powering on the unit make sure the line voltage t
6. ATO Ite e o a RT PST 10 O A A II O ee Tic ede ast E 10 OUI CLIC IA A 10 EST 2 1 GM O16 NAAA SS SEER TSE err 10 FING LINKING A A a nc Lect ec Rm 10 DWESHANNECVALUES ci ee aaa coe ce diran daba elec hilt tate Detalles do 11 APPENDIX 0000 Bray Me ERM SEES EAES AE o A OS 12 A A 12 GENERAL MAINTENANCE sicario dd iii 12 DATAN te ai Pe A a ai 13 PMX PDF OAD cian at se cc io laca do de ee dal lacio aro cel ENE 13 Cable CONNECIONS estomindos 258s 25 5 haa data lili dai ltda ds dica i desa 13 1 0121 2a 154 ae ence ren Rn tee AAR CLR PRE ROR Rt A PTE ERECTED Na DE Be ROR NS REIT REESE REET RE OR ARTO 13 IPN TO Dar ING ONVERSION CHAR dd 14 SETTING UP X DMX SERIAL DATA LINK adas bs 14 SETTING THE OTARTING ADDRES Sea E ed aaa 15 ENE R AU TROUBLE SHOOTING o e 15 CONTACT US na task tested 15 FRE EIN cS OCR Re EEEE E AT E AAEE E uta aan punctuate ta eos 16 CAN garcia peice te II ta decent decane alta tt did tac teat accepts acl css ted tadashi Stereo taetansetbee 16 SEG ANIC a eaa e cat tert ta dscns echt cecum dct lot dene ah eats a a 17 CHAUVET 2010 All Rights Reserved Information and specifications in this User Manual are subject to change without notice CHAUVET assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual 1 BEFORE YOU BEGIN What is included gt 1xLEDrain 38C gt 1x Warranty Card gt 1x User Manual Unpacking Instructions Immediately upon receiving a fixture
7. ALUE FUNCTION 4 Red 000 lt gt 255 Dimmer 0 100 9 Green 000 lt gt 255 Dimmer 0 100 3 Blue Dimmer 0 100 5 Appendix 11 Color Macros overrides CH 1 3 When CH 6 is set 032 223 CH 5 controls the speed 4 19 2010 1 08 PM 9 APPENDIX DMX Primer There are 512 channels in a DMX connection Channels may be assigned in any manner A fixture capable of receiving DMX will require one or a number of sequential channels The user must assign a starting address on the fixture that indicates the first channel reserved in the controller There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required Choosing a start address should be planned in advance Channels should never overlap If they do this will result in erratic operation of the fixtures whose starting address is set incorrectly You can however control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation In other words the fixtures will be slaved together and all respond exactly the same DMX fixtures are designed to receive data through a serial Daisy Chain A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture Use an order that
8. Snapshot seamos O Outdoor Use LEDrain3 It s bu Sound Activated Y Cree Minki IC EA Master Slave ES Auto ranging z Power Supply veer serviceable CTE User Manual DA Valve Innovation Performance 3000 N 29 Ct Hollywood FL 33020 U S A 800 762 1084 954 929 1115 FAX 954 929 5560 www chauvetlighting com TABLE OF CONTENTS T BEFORE YOU BEGIN cursar aces cceceaus aces eaa eaa eeaeee eTa aera iaaeaie 3 WEA TI INOUE D ataa a aE E E E 3 UNPACKING NS a A 3 MANTENEMOS e E 3 A A ee Se ee SE SOE Ee ASE I ee 3 sy Vel al NUNES E Oe EEN Se re OT Ta S 4 INTRODUCTION tape easement eran ite nA o eR eR ee e el EA 5 PEA RE SHAS ate ccc tS e e dd a o termediate lh dd dae 5 PRODUCT OVERVIEW atracado oido iodo 5 ne ten lA Crk O MERLE PULES EVIE SESS OTA VREO A PUEI ETRE SECRET SOOO SR OTE UAE ONE TERESI EISEN APNE AE SS Ae SOLACE EROS SM AE SINCE 6 NN 6 POW CT LINING A onan etn ail atti Gel aa te ahaa anata aaNet al aac kaha 6 o A a a 7 OOD E AN O II II la yes A nen sec A 7 1518181198 AEPA ESE nme nen Rice aan ee Meee A aN er ae nen A E eT Oe NR re en E ne ce 7 4 OPERATING INSTRUCTIONS caiste aiii tic 8 CONFIGURING THE STARTING ADDRESS dada 8 MI A O EETA 8 ACCESSING THE 2 PERSONALES a A IA AA E E A EA E Acad 8 MASTER SLAVE MODE SOUND ACTIVE AUTO MODE STATIC COLORS cocococconacionecacconanconenancononcnnonanconnan conan cononn conca nacen nene nana 9 STROBE PE ED A A AAA A dada 9 TAI ONE
9. e include the following information on a piece of paper inside the box Your name Your address 3 Your phone number The RMA A brief description of the symptoms Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customer s responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Any other claim for items such as missing component part damage not related to shipping and concealed damage must be made within seven 7 days of receiving merchandise 16 4 19 2010 1 08 PM Technical Specifications WEIGHT amp DIMENSIONS HEC Peer o gan tenet ee eee ee eee ee ee ee eee 6 2 in 157 mm AAA e sect ors ANAE EET E EEOAE EENE E EAEE EEE TE 7 4 in 188 mm A O y O E ees 11 2 in 284 mm A 2 8 lbs 1 2 kg POWER Auto ranging Power Supply usar diia 100 240 VAC 50 60 Hz Power Consumption 120 VAC 60 HZ ooooocccnnncccncnncccnnncnnnnanonnnnncnonos 10 W 0 2 A max 0 2 A inrush Power Consumption 230 VAC 50 HZ cocoooccncconoccnncononcnncononnnnnnnnnnnnnnnos 9 W 0 1 A max 0 2 A inrush Power ouput sais 37 units max FUSE omia oa e II EN F 2 A 250 V LIGHT SOURCE EDS T a a EER a e a e a ad 75 x 10 mm 25 red 25 green 25 blue 100 000 hrs PHOTO OPTIC Lumian e O T a a ee 1 033 lux Beant ANO Essere E r N 15 Field UNS tach cle o E a aconloiasiano ide 23
10. o read the data on the channel indicated by the starting address For example a fixture that uses seven DMX channels and is addressed to start on DMX channel 100 will read data from channels 100 101 102 103 104 105 and 106 Choose the starting addresses for each fixture so that the channels used do not overlap In addition you should note the starting address selected for future reference The LEDrain 38C fixture uses seven or three DMX channels If this is your first time using DMX we recommend reading the DMX Primer section in the Appendix DMX Operation This is the operating mode which will allow for control with an external DMX controller You must set the starting address for this mode If this is your first time using DMX then it is recommended that you refer to the DMX Primer section in the Appendix of this manual Mode DIP switches DMX 1 9 set to the DMX starting address 10 Off Accessing the 2 Personalities There are two personalities for this fixture There is the standard 7 channel personality with strobe and color macros and then there is the basic 3 channel RGB personality Please see the DIP switch settings to access each of these personalities below Mode DIP switches 7 CH 11 12 Off 3 CH 11 On 5 Appendix 8 4 19 2010 1 08 PM Master Slave Mode Sound Active Auto Mode Static Colors This mode allows a single unit to run a standalone program while 1 or more other units foll
11. o which you are connecting it is within the range of accepted voltages Always connect the fixture to a switched circuit Never connect the fixture to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used only as a 0 to 100 switch To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture or refer to the fixture s specifications chart A fixture s listed current rating indicates its average current draw under normal conditions Always connect the fixture to a circuit with a suitable electrical ground Power Linking A A 3 Setup This fixture contains power linking via the Edison outlet located in front of the power input cable Please see the diagram below for further explanation The maximum quantity of fixtures that may be linked is 37 Additional power link out Fixture 2 P Ss Z Fixture 1 The power linking shown in this document is for the Chauvet North American version ONLY Therefore it is the customer s responsibility to check with the Dealer Distributor regarding power linking on the local version of the product Connections and availability may change depending on the power requirements and or regulations of each country region 6 4 19 2010 1 08 PM Mounting 3 Setup Orientation The LEDrain 38C may be mo
12. optics Clean with soft cloth using normal glass cleaning fluid Clean the external optics at least every 20 days Clean the fixture at least every 30 60 days Always dry the parts carefully after cleaning them Never spin a fan using compressed air 12 4 19 2010 1 08 PM Data Cabling To link fixtures together you must obtain data cables You can purchase CHAUVET certified DMX cables directly from a dealer distributor or construct your own cable If you choose to create your own cable please use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference DMX Data Cable Use a BeldenO 9841 or equivalent cable which meets the specifications for EIA RS 485 applications Standard microphone cables cannot transmit DMX data reliably over long distances The cable must have the following characteristics Type shielded 2 conductor twisted pair Maximum capacitance between conductors 30 pF ft Maximum capacitance between conductor and shield 55 pF ft Maximum resistance 20 ohms 1000 ft Nominal impedance 100 140 ohms Cable Connectors INPUT Cabling must have a male XLR connector on one end and a female XLR connector on the other end 120 ohm 1 4 W resistor between pin 2 DMX and pin 3 DMX on the output of the last fixture DMX connector configuration COMMON O 3 8 OUTPUT 2 A eee Ara chy ES Po A EE
13. ow the same operation This requires the fixtures to be linked with DMX cables Please see the section on Fixture Linking 1 The Master unit may be operated in Automatic Sound Active and Static Colors 2 Adjust the DIP switches to the Slave position on the slave units and they will react the same as the Master See below for DIP switch assignment Mode DIP switches Slave 2 11 Off 1 On Strobe Speed This fixture has a strobe speed adjustment which will decrease the maximum speed Please see the setting below for lowering the strobe rate for compatibility mode Mode DIP switches Standard mode 6 Hz 18 Hz 12 On Decreased Speed 2 Hz 6 Hz 12 Off 5 Appendix 9 4 19 2010 1 08 PM Standalone Operation Automatic This fixture has a preprogrammed color fade program This is accessed via the DIP switches on the back of the fixture and the speed may be increased as well Please see the chart below for further explanation Mode DIP switches Master Auto 7 9 10 On Increase Speed 1 6 On add more DIP switches to reach higher speed Sound Active This fixture has preprogrammed sound triggered chases These are accessed via the DIP switches on the back of the fixture and the sensitivity may be adjusted using the audio adjustment knob Please see the chart below for further explanation Mode DIP switches Master Sound 10 On Static Colors This unit has separate DIP switches for each of the 3 colors red green
14. provides for the easiest and most direct cabling Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors The shield connection is pin 1 while pin 2 is Data Negative S and pin 3 is Data positive S General Maintenance A 5 Appendix To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance e Unplug fixture from power e Use a vacuum or air compressor and a soft brush to remove dust collected on external vents e Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue e Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens e Gently polish optical surfaces until they are free of haze and lint The cleaning of external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates Damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s
15. r cable conversion 3 PIN TO 5 PIN CONVERSION CHART Conductor 3 Pin Female Output 5 Pin Male Input Ground Shield Pin 1 Pin 1 Data signal Pin 2 Pin 2 Data signal Pin 3 Pin 3 Not used Pin 4 Not used Pin 5 Setting up a DMX Serial Data Link Universal DMX Controller l l ea ee eee h 1 Connect the male 3 pin connector side of a O Om JOOOOUO Q Q 22 Z the DMX cable to the output female 3 pin So LILI ee ohn gt eses uy ka lir E y ax 0 connector of the controller E 0 Q Or 0 9 3 gt 19 O49 B 2 0 Bo 2 Connect the end of the cable coming from 2S me ne 2 2 the controller which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector This drawing provides a general illustration of the DMX input output panel of a lighting fixture 3 Then proceed to connect from the output as stated above to the input of the following fixture and so Continue the link 5 Appendix 14 4 19 2010 1 08 PM Setting the Starting Address This DMX mode enables the use of a universal DMX controller device Each fixture requires a start address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that uses six DMX channels and wa
16. raph contains important installation or configuration information Failure to comply with this information may prevent the fixture from functioning correctly WO gt 1 Before You Begin This paragraph reminds you of useful although not critical information 3 4 19 2010 1 08 PM Safety Inst ructions Please read these instructions carefully It includes important information about the installation usage and maintenance of this product 1 Before You Begin Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure there are no flammable materials close to the unit while operating The unit must be installed in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots are blocked Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse source Secure fixture to fastening device using a safety chain Maximum ambient temperature Ta is 104 F 40 C Do not operate fixture at temperatures higher
17. s addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 and 105 Choose start addresses so that the channels used do not overlap and note the start address selected for future reference If this is your first time addressing a fixture using the DMX control protocol we suggest jumping to the Appendix section and reading the heading DMX Primer It contains very useful information that will help you understand its use General Troubleshooting SYMPTOM POSSIBLE CAUSE S e Excessive circuit load Breaker Fuse keeps blowing Short circuit along the power wires e No power e Loose power cord e Wrong DMX addressing Device does not power up e Damaged DMX cables Wrong polarity settings on the controller Fixture is not responding to DMX Loose DMX cables Faulty DMX interface Faulty Main PCB e Non DMX cables e Bouncing signals Loss of signal e Long cable Low level signal e Too many fixtures e Interference from AC wires POSSIBLE ACTION S Check total load placed on the electrical circuit Check for a short in the electrical wiring internal and or external Check for power on power outlet Check power cord Check Control Panel and unit addressing Check DMX cables Check polarity switch settings on the controller Check cable connections Replace DMX input Replace Main PCB Use only DMX compatible cables Install terminator as sugge
18. sted Install amplifier right after fixture with strong signal Install an optically coupled DMX splitter after unit 32 Keep DMX cables separated from power cables or black lights If you still have a problem after trying the above solutions please contact CHAUVET Technical Support Contact Us World Wide General Information CHAUVET 3000 North 29 Court Hollywood FL 33020 voice 954 929 1115 fax 954 929 5560 toll free 800 762 1084 Technical Support CHAUVET 3000 North 29 Court Hollywood FL 33020 voice fax World Wide Web 5 Appendix 954 929 1115 Press 4 954 929 5560 Attention Service www chauvetlighting com 4 19 2010 1 08 PM Returns Procedure Claims 5 Appendix Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Return Merchandize Authorization Number RMA Products returned without the RMA will be refused Call CHAUVET and request an RMA prior to shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return Be sure to pack fixture properly any shipping damage resulting from inadequate packaging is the customer s responsibility As a suggestion proper UPS packing or double boxing is always a safe method to use CHAUVET reserves the right to use its own discretion to repair or replace product s If you are given an RMA pleas
19. unted in any safe position provided there is adequate room for ventilation Rigging Be sure that the structure can support the weight of the fixture Please see the Technical Specifications section of this manual for a detailed weight listing Mount the fixture securely This may be done with a screw nut and bolt or a hanging clamp The hole in each bracket is 13 mm in size When rigging consider routine maintenance and control panel access Please see the following steps for installation e Be sure to orient the gel frame release so that it is pointing up Please see the diagram below for a visual reference e If the power link out is intended to be used with multiple fixture take into account the length of each power cable and mount the fixtures close enough to one another to accommodate for this e When aiming the fixtures you may use the bracket adjustment knob Loosen the knob adjust to the desired angle and then tighten the knob by turning clockwise Do not use tools for this step as it may cause damage e There is a secondary portion of the bracket which may be used primarily for floor standing positions e Safety cables must always be used Mounting Bracket Secondary bracket used primarily for standing position 7 4 19 2010 1 08 PM 4 OPERATING INSTRUCTIONS Configuring the Starting Address Each fixture requires a starting address from 1 512 A fixture requiring one or more channels for control begins t
Download Pdf Manuals
Related Search