Chamberlain RGAIPI User's Manual
Contents
1. colder will beep for approximately 30 environments seconds indicating that programming is successful To stop the beeps earlier press the Select Button on the Indoor Intercom Program Outdoor Intercom to Gate Operator Refer to the owner s manual of the gate operator to find the location of the Learn button Step 2 Adhere rubber pads to bottom Repeat Steps 1 and 2 for any additional intercoms Step 1 Press the Learn button on the gate operator Outdoor Intercom Step 2 Within 10 seconds press and hold the Learn button on the Outdoor Intercom until a beep is heard Install 4 AA Alkaline batteries not provided Lithium batteries recommended for colder environments Mount Outdoor Intercom The Outdoor Intercom should be mounted where it is easily accessible to a driver The Outdoor Intercom can be mounted by using the included screws or by using the double sided mounting tape It is recommended to use the mounting tape on surfaces such as metal or glass Mounting with Screws Step 1 Mount Outdoor Intercom with small silver screws Screw the top two screws halfway into the mounting surface Place back of Outdoor Intercom over screws Tighten screws Put the remaining silver screws into the bottom holes of Outdoor Intercom Tighten screws Mounting with Tape Step 1 Clean back of Outdoor Intercom and mounting surface using the alcohol wipe Step 2 Peel off whi2. CHAMBERLAIN Overview The Wireless Gate Access Intercom allows homeowners to communicate with guests at the gate and operate the gate from inside the house The Indoor Intercom emits a doorbell sound and establishes a secure 900 Mhz digital radio link with the Outdoor Intercom The Wireless Gate Access Intercom is compatible with various Chamberlain Wireless Products and all Chamberlain Gate Operators Carton Inventory oo Rubber Pads Ba Mounting Tape m Alcohol Wipe Outdoor Intercom Operation amp Features Indoor Intercom Volume Button Talk Power On Select Button AC Adapter Learn Button Dipswitch 1 Dipswitch 2 On Off To turn Indoor Intercom ON press any button To turn Indoor Intercom OFF hold down the Volume button for 5 seconds Model RGAIPI Wireless Gate Access Intercom Talk Button Following the ringing of the doorbell by a guest press and hold the Talk button to talk to the guest Once the link to the Outdoor Intercom is made any other intercoms in the network cannot hear the conversation Select Button During a conversation the Select button can be pressed to open the gate A beep will be heard and the gate will open To open the gate when not in a conversation press and hold the Select Button for 10 seconds Volume Pressing the Volume button repeatedly will cycle through volume levels Battery The AA Alkaline batteries not provided will last up t
3. Check the batteries in both intercoms Ensure the Indoor Intercom is programmed to the Outdoor Intercom See Program Indoor Intercom to Outdoor Intercom Indoor Intercom is not getting expected transmission range Keep antenna vertical Keep Outdoor Intercom away from trees metal objects and electrical wiring Cell phones cordless phones or other radio devices near the Indoor Intercom may also limit range Indoor Intercom beeps once every ten minutes The battery is low in the Indoor Intercom Replace with AA Alkaline batteries or operate it with AC Adapter not provided A 9 12 volt 500mA AC Adapter may be used center positive polarity on the round plug Indoor Intercom beeps three times every ten minutes The battery is low in the Outdoor Intercom Replace with AA Alkaline batteries Need to clear Indoor Intercom s memory Press and hold Learn button an initial beep will be heard Continue to hold until a second beep is heard about 15 seconds Ensure other intercoms are not activated during this time Intercoms in the network that are on will signal during the clearing process Once memory is clear the intercom can be programmed to a new network Outdoor Intercom does not function Check batteries in Outdoor Intercom When you press the Call button you should hear a tone Ensure Outdoor Intercom is connected to a network Mounting Template 1 3 8 I BF 4 1 4 A 114A3670B FOR TECH
4. NICAL SUPPORT DIAL OUR TOLL FREE NUMBER 1 800 528 9131 www chamberlain DIY com NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2008 The Chamberlain Group Inc All Rights Reserved
5. o a year depending on use Lithium batteries recommended for colder environments When batteries are low intercom will emit two beeps every ten minutes An AC Adapter not provided can also be used to power the intercom In this case both the power and channel lights will remain on Outdoor Intercom OPTIONAL Call Button Learn Button Dipswitch Call Button To communicate with the Indoor Intercom press and release the Call button A doorbell sound will be heard on the Indoor Intercom Once a secure link is made the Call button on the Outdoor Intercom does not need to be pressed to speak again Battery The AA Alkaline batteries not provided will last up to a year depending on use Lithium batteries recommended for colder environments Volume To increase the Outdoor Intercom volume set Dipswitch 4 to OFF Sensitivity To increase sensitivity on the Outdoor Intercom set Dipswitch 3 fe to OFF NOTE Dipswitch 1 must always remain ON Dipswitch 2 is not used o L gt ml Assemble Program Indoor Intercom to Indoor Intercom Outdoor Intercom Step 1 Press the Learn button on the Indoor Intercom until a beep is heard Step 2 Within 10 seconds press the Learn button on the Outdoor Intercom until a multi beep is heard Step 1 Install 4 AA Alkaline batteries not provided NOTE The Indoor Intercom Lithium batteries recommended for
6. te paper from mounting tape Firmly press mounting tape on back of Outdoor Intercom Peel paper from mounting tape Firmly press Outdoor Intercom onto mounting surface Secure Cover Secure cover with the two large black screws Program Additional Intercoms NOTE Some older versions of Chamberlain Wireless Intercoms are not compatible with the Gate Access Intercom Ensure that the additional intercoms state that they are compatible with Chamberlain s Gate Access Intercom The Indoor Intercom can be programmed to at least one other intercom to become a network or it can be programmed into an existing network Any intercom that has been programmed into the network can respond to a call and operate the gate Press the Learn button on the Indoor Intercom until a beep is heard Within 10 seconds put the new intercom into Learn Mode refer to table below INTERCOM LEARN MODE Press the Learn button until a beep is heard Press and hold both buttons for 5 seconds Each intercom will emit a tone when programmed into network Repeat for any additional intercoms NOTE Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared Press and release the Talk button on the Indoor Intercom to verify network is complete Troubleshooting Indoor Intercom does not receive voice transmission from Outdoor Intercom
Download Pdf Manuals
Related Search