CDA FWV460 User's Manual
Contents
1. appliance has been fitted with a BS 1363A 13 amp fused plug To chai follow the steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to connect an alternative plug If the fitted plug is not suitable for your socket outlet then it should be cut off and disposed o electric shock A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e The wire which is coloured GREEN and YELLOW must be connected to the terminal whic by the Earth symbol a or coloured GREEN and YELLOW e The wire which is coloured BLUE must be connected to the terminal which is marked with coloured BLACK e The wire which is coloured BROWN must be connected to the terminal which is marke coloured RED or BROWN If in doubt regarding the electrical connection of this appliance consult a qualified electrician supply cable the appliance may require removing for servicing N B Ensure that the plug socket is situated in an easily accessible place CDA To contact our Customer Care Department or please contact us on the details belo2. metre water hose can be cut down to the required length using a sharp knife You should ensure no burrs are left on the hose The water connection fitting and flow reducer are prefitted However if you should need to reconnect the fitting proceed as follows Connect one push fit tap adaptor to each end of the water hose fig 4 Insert the supplied flow restrictor and black o ring into the tap adaptor as per fig 6 Please note the flow restrictor should be fitted to the tap adaptor that is to be fitted to the water supply tap Secure the tap adaptor that does not contain the flow restrictor to the valve on the back of the appliance and then connect the remaining tap adaptor to the mains water supply tap Once both tap adaptors are securely fitted turn on the water supply and check for leaks oo Flow restrictor Please note Due to the weight of this appliance the housing unit must be secured to the wall prior to installation You must ensure that all water connections are sound and check there are no leaks before completing installation For best performance the mains water pressure must be between 011 3 bar Do not use outdoors Do not install near a hob or oven To reduce the risk of electric shock do not mount over a sink Electrical information Warning This appliance must be earthed Green amp Yellow to Earth Brown to 13 Amp Fuse Cord Clamp The mains lead of this
3. press ON before emptyi holding 9 to flush the system through with the bicarbonate solution from the water 5 Repeat steps 3 and 4 6 Fill the water tank with 2 5 of water 7 Use the water empty function press and hold M and then press ON before emptyin W to clear out any bicarbonate solution remaining 8 Repeat steps 6 and 7 9 Turn the ice maker off 10 Turn the mains water supply back on if applicable or fill the water tank 11 Turn the ice maker on Normal operation will resume The Icemaker Bicarbonate of soda is a safe compound and poses no risk to health It is commonly availa supermarkets You should only use cold drinking water in this appliance with water hardness level less th The water tank can be removed for cleaning following the steps above and then lifting it The water storage tray is located below the ice drawer In normal use this fills with water dispensing this does not constitute a fault The Icemaker To make ice The icemaker will make ice automatically once it is switched on and will continue to make i is full Whenever ice is removed the icemaker will make more ice until the compartment i To dispense water The amount of water dispensed from the water nozzle is controlled by three different butt U water glass D water jug W manual setting this button dispenses water as long as the button is pressed The water nozzle is height adjustable for ease of use
4. the machine at the switch on the left side of the machine Push the machine back into the housing Switch on the machine by pressing the ON button The machine is now ready for use and the display shows ICE ON WATER READY Duk wn The water tank It is possible to use the appliance without connecting it to the mains water supply There i can be used in this instance To ensure the best results from your appliance it is recomme emptied frequently and refilled with fresh water and no water be left in the tank for long When the water tank is empty the message WATER MISSING will show on the display To fill the water tank 1 Pull the machine out of its housing by lifting the handle of the machine and pulling it t 2 Open the lid of the water tank and fill it until the water is 4cm from the top level The 3 Push the machine back into the housing Please note You should follow the steps below in order to remove any impurities from the system and from your ice maker Failure to carry out this simple procedure could cause problems or da icemaker 1 Turn off the mains water supply if applicable 2 Use a sterilising solution such as Milton fluid to clean the removable ice drawer and the the instructions supplied with the sterilising solution to ensure the ice drawer is thorou 3 Fill the internal water tank with 2 51 of water then add a spoonful of bicarbonate of so 4 Use the water empty function press and hold Mand 2 then
5. To adjust the height hold the black o nozzle and raise or lower it to the height required The nozzle will automatically remain at To change the preset buttons It is possible to adjust the amount of water dispensed by the preset buttons U e D To under the water nozzle and press button 5 until the required amount has been dispensed pressing buttons Wer for the water glass button or buttons Wer X for the water jug b Please note To stop water dispensing once a preset button has been pressed simply press the button a To dispense ice When the ice drawer is full the display shows ICE FULL WATER READY Open the drawer fully and use the scoop provided to remove the ice as required Please note To ensure the ice is fresh we recommend you empty the ice drawer every 6 8 hours If the ice drawer is not emptied for a long period of time the appliance will go on standby minutes and the display shows ICE OFF WATER READY After the standby period has end to make ice again If you do not want to wait for the standby period to finish press the O Care and maintenance Always disconnect the appliance from the power before any cleaning or maintenance As the icemaker has a stainless steel or enamel surface you should use a nonabrasive clean including Cif will scratch the surface and could erase the control panel markings Stainles cleaned by simply using a dilute solution of water and mild detergent and drying to a shine Propr
6. a reminder of the need to dispose of household appliances separa a crossed out wheeled dustbin Please note This appliance is designed solely to produce ice cubes and dispense chilled water Other ty and may prove dangerous The CDA Group Ltd will not be held liable for any damage caus the appliance e Read all instructions thoroughly before use e Before first use you must allow the icemaker to settle for at least twenty four hours pri e To protect against fire electrical shock and injury to persons do not immerse cord or pl e The use of accessory attachments not recommended by The CDA Group Ltd may resul e Ifthe appliance is switched off you should allow five minutes before switching it on ag damage to the compressor Icemaker oe al Control Panel Water Nozzle Ice Drawer Water Tray Drip Tray Icemaker control panel 1 2 3 4 1 On button 2 Off button 3 Water glass button this button dispenses a small amount of water 4 Water jug button this button dispenses a large amount of water 5 Manual water button this button dispenses water as long as the button is pressed 6 Maintenance button this button allows the icemaker to automatically empty the The Icemaker Before first use Pull the machine out of its housing by lifting the handle of the machine and pulling it t Fill the water tank even if the appliance is to be plumbed in to the mains water supply Turn on
7. fe CDA Manual for Installation Use and Maintenance Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect u Please note that CDA reserve the right to invalidate the guarantee supplied with this produc or misuse of the appliance Under no circumstances should any external covers be removed for servicing or maintenan qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cust with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This appliance has been designed constructed and marketed in compliance with safety 2006 95 EEC Low voltage and requirements of EMC Directive 2004 108 EEC This appliance has been manufactured to the strictest standards and complies with all Electrical safety LVD and Electromagnetic interference compatibility EMC Parts inte food conform to EEC 89 109 4 IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT DIRECTIVE 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It authority differentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences fi deriving from inappropriate disposal and enables the constituent materials to be recovere energy and resources As
8. ietary stainless steel cleaners are available We recommend the CDA E Cloth available for cleaning stainless steel surfaces You should remove and clean regularly the water tank the ice compartment drawer and b Once cleaning is complete reconnect the mains power supply If the appliance is not to be used for prolonged periods of time you should empty clean tl appliance To empty the icemaker follow the steps below 1 Press and hold button 9 and together and then press button ON This will em icemaker s internal system The display will show ICE OFF WATER EMPTY to con system is empty 2 Empty the ice from the ice compartment w Place a jug under the water nozzle and press button M until no more water is disp 4 To make sure the pipework is completely empty you should unscrew the cap at th the last of the water IMPORTANT Steam cleaners must not be used when cleaning this appliance Ensure that all parts are correctly replaced after cleaning before attempting to use the ice Troubleshooting WATER MISSING shows in the display The water tank is empty and needs to be refilled ICE FAULT WATER READY shows in the display Turn the icemaker off with OFF and the main switch on the side before at first switch on switching it on again The icemaker emits a continuous beep UV Sterilizer needs replacing contact CDA Customer Care The dispensed water has an unpleasant taste Ensure that only water pi
9. pes suitable for drinking water are used ICE FAULT shows in the display Turn the icemaker off with OFF remove some ice and turn it on again We recommend that the unit is not left on permanently IMPORTANT Do not operate with a damaged cord plug after the appliance malfunctions or has been da contact CDA Customer care for inspection repair or adjustment Installation IMPORTANT THIS APPLIANCE SHOULD BE FITTED BY SUITABLY QUALIFIED PERSON 1 Slide the base unit into the housing ensuring the dimensions are correct as per figure 1 2 Fix the base unit in place by attaching the 10 screws in to the holes as shown in figure 2 and figure 3 If the sides of the base are not flush with the sides of the housing then use the shims provided 3 Push the runners fully closed on the base unit 4 Connect the plug to the plug socket This must be accessible after the appliance has been installed 5 Using an appropriate supply pipe connect one end of the hose to the threaded inlet of the valve on the dispenser located at the rear of the appliance 6 Insert the flow restrictor between two rubber washers then connect the other end of the pipe to the mains water supply drinking water only 7 Insert the appliance into the housing ensuring that the runners on the machine are located in the runners on the base unit Then slide the appliance fully into the housing Installation If necessary the included 6
Download Pdf Manuals
Related Search