Canon IP6000 User's Manual
Contents
1. 3 Don t place the Reservoir Bottles too much higher or lower than the printer 4 Suggested using in a dry place between 15 and 35 degree Avoid exposure to direct sunlight 5 Don t reverse or lean the continuous ink supply systems during shipping Please make sure all the ink filling holes and ventilation holes are closed tightly during transportation Otherwise the ink may leak 6 Don t sway the cartridge frequently It may cause ink leakage 7 Don t pull out the connector of cartridge and don t tear off adhesive tape at the bottom of cartridge 7 Warning 1 Not drinkable keep it out reach of children 2 Avoid exposure to direct sunshine and don t keep it in high or freezing temperature 3 Avoid collision and fallen down PDF HEH pdfFactory Pro wAWRA Gt www fineprint cn2. the cartridges into cartridge carriage left edge 4cm distance from bottom side Clip the tube on the other side of the support Adjust the tube line make sure cartridge Move the cartridge carriage to the right side arm as shown in the picture carriage can move to the both sides and the of printer Check if there is any problem tube line can come out through the bottom of when moving the cartridge like the position in red circle PDF SEH pdfFactory Pro whHheAS Get www fineprint cn Too long is no good Install well 4 Refill Ink Please pay attention to the ink level in the reservoirs if the ink level is below 1CM as the picture shown above please use refill kits to fill ink into Reservoir bottles Carefully pull out the rubber plugs from the ink refill holes There is possibility of ink spattering Pls be careful Refill ink according to the colors Then re cap the rubber Please keep the printer and the reservoir bottles at the same horizontal line during the process of refilling ink 5 Attention for Maintenance Take out the CISS including the inner cartridges and other components Then remove support arm from printer and re install original cartridges Please inquire local dealer before sending to maintenance 6 Notice 1 Please don t take out cartridge at random after installing the CIS system Keep the reservoir bottles on the same level with the printer 2 Try to keep at least 1 2 inch of ink in the bottles
3. Continuous Ink Supply System for CANON PIXMA IP6000 Installation Instruction For ST Prefilled Version This Version of the Continuous Ink FlowSystemcomes with Prefilled Cartridges and Auto Reset Chips You just need to fill the Reservoir bottles and print The whole operation is very easy It s really an effective tool to save your money PDF cee ERY pdfFactory Pro iHIWRA GME www fineprint cn CIS for CANON PIXMA IP6000 Instruction Thank you for purchasing DP Continuous Ink Supply System We appreciate your support and will try our best to make your experience with our products a pleasant one Printing has been a different experience ever since you installed ST Continuous Ink Supply system on your own printer Just imagining being able to print without regard to the ink level in those expensive little cartridges Please take your time installing ST Continuous Ink Supply system Do not remove your old cartridge until you have the ST CIS system primed and ready to install to prevent the drying of heads In addition make sure you are getting perfect nozzle checks before installing the ST CIS system The ST CIS system won t be able to work properly if the nozzles are previously clogged Most people get a perfect nozzle check the first time after installing the ST Continuous Ink Supply system others may need to run two or three cleaning cycles or let the printer sit for a while before they get the perfect results 1 General Guid
4. e 1 Components A CIS system 1 set B Air filters 6pcs C SupportArm 1 set D Refill Kit 6 pcs E Instruction CD 1pc relit kits 2 Opening box inspection a Check whether all the accessories are ready b Check whether there s leakage of CIS System whether some tubes have been separated from CISS If there is please kindly to contact the local dealer C Check whether there is air space in the tube If the length of air space is more than 20cm please clean the printer head for 2 or 3 times before printing 2 Printer testing 1 Check whether the printer is in normal condition like mechanical status lubrication status etc 2 Print testing lines to ensure the printing head is good condition 3 Print pictures to see whether the printing image is ok PDF cee EAI pdfFactory Pro iWHIWRA Gt www fineprint cn 3 Installation Procedures 1 First step Put CISS on the left side of the printer In the meantime place all the tubes at correct position Then pull the small rubber plug out of Air hole and insert the air filters into air holes as the pictures shown above 2 Install cartridges Pls turn on power Open the cover the cartridge carriage will Turn off the printer and unplug it move automatically to Change Cartridge Place Then take off original Cartridges 3 Installation of continuous ink system Take off the CIS cartridge s bottom cap and Stick support arm 2 5cm distance from
Download Pdf Manuals
Related Search