Briggs & Stratton 1695353 User's Manual
Contents
1. WI 53074 0997 www MasseyLawn com Briggs amp Stratton Yard Power Products Group Copyright 2007 Briggs amp Stratton Corporation Milwaukee WI USA All Rights Reserved gt SNAPPER PRODUCTS 535 Macon Street McDonough GA 30253 www Snapper com AGCO LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 AGCOLawn com2. lt gt Simplicity vo MASSEY FERGUSON AGCO gt SNAPPER OPERATOR S MANUAL Turboless Twin Catcher Turboless Twin Catcher Mfg No Description 1695353 38 Turboless Twin Catcher LL CAUTION Read and follow all instructions Manual Part No 1734772 Revision 01 Rev Date 05 2007 TP 100 4528 01 AT SMAN SAVE THESE INSTRUCTIONS READ THE MANUAL The operator s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation Safe operating techniques an explanation of the product s features and controls and maintenance information is included to help you get the most out of your equipment investment Failure to obey the safety rules could result in loss of control of the unit sever personal injury or death to you or bystanders or damage to property or equipment Safety Icons The alert symbol is used to identify safety information about hazards that can result in personal injury A signal word DANGER WARNING or CAUTION is used with the alert symbol to indicate the likelyhood and the potential severity of the injury In addition a hazard icon may be used to represent the type of hazard An explanation of hazard levels and icons are as follows DANGER This indicates a hazard which if not avoided will result in serial injury or death A WARNING This indicates a hazard which if not avoided could result in seri
3. on carriage bolt D Secure the front of lower chute A to carriage bolt Lift discharge deflector up E Figure 11 Slide the notch of bracket G on to deflector hinge rod F D using wing nut B and locknut C SA RN Figure 11 Install Lower Discharge Chute Ommogou n Lower Chute Wing Nut Nut Carriage Bolt Discharge Deflector Deflector Hinge Rod Bracket Figure 12 Install Discharge Tube A Boot Discharge Tube Seal Puck Metal Wire Form Slits INSTALL DISCHARGE TUBE 1 Slide discharge tube B Figure 12 into seal C It may be necessary to lengthen several slits F in order for tube A to fit into seal B 2 Attach the discharge tube B and Inset to boot A and secure the tube by moving wire form E down over metal puck D mmogogo 10 Normal Removal amp Installation of Lower Discharge Chute Note See previous pages for more detailed installation and operation instructions if necessary 1 Lift discharge deflector up E Figure 13 2 Slide the notch of bracket G on to deflector hinge rod F 3 Secure the front of lower chute A to carriage bolt D using wing nut B and locknut C Note Locknut C is intended to keep wing nut B permanently on carriage bolt D A Lower Chute Figure 13 Install Lower Discharge Chute Wing Nut Locknut Carriage Bolt Dis
4. 7 16 14 x 1 1 4 Existing Figure 3 Baffle Assembly Install Baffle and Blade Note Units with an anti blowout baffle do not require the Clean Sweep baffle 1 Remove mower deck See OPERATOR S MANUAL 2 Install notched side of baffle A Figure 3 to discharge side of deck securing with 5 16 18 x 2 carriage bolt C and 5 16 18 locknut D Install 5 16 18 wing nut F and locknut G to carriage bolt C as shown 3 Secure center of baffle A to deck using 5 16 18 x 2 carriage bolt C spacer B and nut D Secure LH end of baffle A to deck using 5 16 18 x 5 8 carriage bolt E and nut D 4 Remove right hand blade A Figure 5 Use a block of wood to prevent blade rotation while loosening the capscrew 5 Reinstall the large washer B Figure 6 spring washer C and capscrew D Use a wooden block A to prevent blade rotation while tightening the capscrew D to 45 55 ft Ibs 61 75 Nm Figure 5 Blade Installation Mowers A 4x4 Wood Block B Hex Washer C Spring Washer D Blade Capscrew Install Lower Chute Components INSTALL BRACKET AND PIN ON LOWER CHUTE 1 Secure the puck C Figure 6 to lower chute A using 5 16 18 x 3 4 capscrew D and 5 16 18 locknut E 2 Install bracket F and deflector prop G to lower chute A using 5 16 18 x 3 4 capscrews D and 5 16 18 locknuts E Figure 6 Install Pin and Bracket omnmgo
5. al injury or death A CAUTION This indicates a hazard which if not avoided might result in minor or moderate injury Hazard Symbols and Meanings a Remove Key Before Servicing Rotating Parts Do Not Touch Table of Contents Operator Safety toa iride Reato amp 2 Operator Safety is Gora ille lana 2 Safety Decals cott ode tet eee Gb eoe core oen tra 2 Mowing with the Catcher 3 Before Operation I n 3 After Operation 3 Storing the Catcher 3 ASSUME rale Ae ee le ES oe ee oe es 5 Install Mounting Plates amp Spacers Broadmoor 1600 2600 LT Series 5 Install Baffle and Blade 6 Install Lower Chute Components 7 Install Bag and Cover Support 8 Install Hitch and Upright Support Assembly 8 Install Cover Assembly LL 8 Install Collector Bags 9 Install Lower Discharge Chute 0 cc cece cece eee ees 9 Install Discharge Tube LL 10 Normal Removal amp Installation 11 Lower Discharge Chute 11 Bagger Removal exu thie Rive ie bes 12 VET ASB OD ZELO uonej ejsu 9 ra 3 JJ 1 3 lt A GENERAL WARNINGS Know the unit s controls and how to stop quickly READ THE OPERATOR S MANUALS Read and obey all safety decals Only allow responsible adults who are familiar with the instructions to operate the unit Disengage the PTO Shut off the engine and wait for all moving parts to stop before attaching adjustin
6. charge Deflector Deflector Hinge Rod Bracket UH E ra 3 E JJ 1 3 lt eOmmog ouo 11 Normal Removal amp Installation A Hitch Support G Discharge Tube Assembly H Wire Form B Cover I Puck C Pin J Boot D Hair Pins K Seal E Bag L Frame Spacers F Grass Bag Hanger Figure 14 Normal Installation amp Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger the mower deflector MUST be properly installed in the down position and retained by the spring latch Bagger Removal 1 Disconnect the discharge tube G Figure 14 from boot J by moving wire form H up and out from metal puck I Remove discharge tube G from seal K 2 Remove hair pin clips D and pins C then remove cover B see Figure 9 Note To prevent loss of parts reinstall pins C and hair pins D in support assembly hinge pivots E Figure 9 12 3 Remove and empty bags E Figure 10 4 5 Lift discharge deflector up E Figure 13 Loosen do not remove wing nut B and lock nut C Slide lower chute A off carriage bolt D and deflector hinge rod F Normal Removal amp Installation 13 Simplicity MANUFACTURING INC 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www SimplicityMfg com vo MASSEY FERGUSON LAWN amp GARDEN EQUIPMENT 500 N Spring Street PO Box 997 Port Washington
7. d other debris which may be caught or thrown by the mower blades Check grass condition If wet wait until later in the day If grass is wet the grass catcher is likely to become plugged For efficient bagging air circulation under the mower deck through the chute and into the bag is very important For this reason BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover A CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet as well as the Operator s Manual for the tractor and any other attachments Never operate on slopes greater than 17 6 10 After Operation Remove any debris from the the screen on the underside of the lid The blower housing and tube should be removed for cleaning Inspect the grass bags for wear or damage Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover Storing The Grass Catcher Clean the grass catcher thoroughly using a mild detergent other products may damage the tube Remove any debris from the screen on the underside of the lid If paint has been scratched on metal parts touch up with paint or apply a thin film of oil to prevent corrosion S
8. g or disconnecting any part of the collection system Check the collection system to make sure it is bolted tightly to the unit DO NOT operate the unit without either the entire grass catcher or the deflector in place Turn off the PTO to disengage the blades when not mowing DO NOT mow in reverse unless absolutely necessary Always look down and behind before and while travelling in reverse DO NOT turn sharply when travelling alongside a building or any object Slow down before turning DO NOT carry passengers When collection system is removed from the mower deck the deflector must be properly installed Collector bags are subject to deterioration and wear during normal use Inspect the bag SAFETY DECALS This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your rider attachments and mower should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is impor
9. pen the hopper while the mower blades are turning Do not operate the mower without the complete catcher in place 3 Decal WARNING Thrown Objects Hazard Part Number 1732819 Read and obey all operation and warning decals Mowing with the Catcher Always operate with throttle at full speed when mowing Grass should be cut often and not too short If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging If grass is long operate with mower in high cutting position for first pass cutting again in a lower position on a second pass Do notopen the cover with mower engaged If a large amount of cut grass is spilling out from under deck the tube may be plugged or the bags may be full discontinue mowing stop the unit disengage the PTO shut off the engine and then empty the catcher or clear the tube A WARNING ALWAYS shut off the tractor Disengage the PTO and allow all moving parts to stop BEFORE disconnecting or clearing tube or emptying catcher Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine rider and mower free of grass leaves and excess grease Do not stop or park rider over dry leaves grass or combustible materials Before Operation Clear the lawn of all sticks stones wire an
10. tant The safety decals below are on your product If any decals are lost or damaged replace them at once See your local dealer for replacements TP 600 2562 01 AT SMA periodically for tears holes or weak spots and replace with a new bag that meets manufacturer s durability standards If the mower stalls or the collector chute plugs 1 Disengage the PTO 2 Stop the engine and remove the key 3 Set the parking brake and wait for all moving parts to stop 4 Remove the foreign object or clear the chute with a piece of wood before restarting the engine NEVER place hands into COLLECTOR OR MOWER housing to clear jammed objects Blower OR MOWER may rotate when object is removed For added stability and to prevent tipping or loss of control a Use reduced speed on uneven ground and when turning corners b Reduce loads on hillsides It is recommended that the collection system be kept only half full when negotiating any slopes Start mowing on slopes when the collection system is empty c Mow up and down the face of slopes never across the face of any slope Never operate on slopes greater than 17 6 10 These labels are easily applied and will act as a constant visual reminder to you and others who may use the equipment to follow the safety instructions necessary for safe effective operation Attachment Decal Thrown objects hazard Objects thrown by the mower can seriously injure or kill you Do not o
11. tore in a dry area Dry thoroughly before storing for a long period of time Always store away from moisture A CAUTION Do not leave grass in bagger containers Empty containers after each use and before storing Failure to do so may result in spontaneous combustion which could develop into a fire Assembly INSTALL MOUNTING PLATES BROADMOOR 1600 2600 LT SERIES Install Plates amp Spacers 1 Mount the side brackets C Figure 1 to both sides of the frame using the holes shown Secure with one 3 8 16 x 1 capscrew D 3 8 lockwasher B and 3 8 16 nut A per side 2 Install the rear spacers C Figure 2 Secure with two 1 2 13 x 2 1 2 capscrews E washers D spacers C and 1 2 13 nylock nuts A per side Figure 1 Install Side Brackets A Nut 3 8 16 B Lockwasher 3 8 C Side Bracket D Capscrew 3 8 16 x 1 Figure 2 Install Rear Spacers A Nylock Nuts 1 2 13 B Capscrew 1 2 13 x 2 1 2 C Spacers D Washers 1 2 lt gt E Ex Torque Capscrew to 45 55 ft Ibs 61 75 Nm rATTCI O Baffle New Spacer New Carriage Bolts 5 16 18 x 2 New Locknuts WHIZ Lock 5 16 18 New Carriage Bolt 5 16 18 x 5 8 New Wing Nut Assembly Large 5 16 18 New Locknut Center Lock 5 16 18 New Grass Shield Existing Blade High Lift New Hex Washer Existing Washer Existing Capscrew
12. wp Lower Chute Locknut 1 4 20 Puck Metal Capscrews Thin Head 5 16 18 x 3 4 Locknuts 5 16 18 Bracket Defflector Prop INSTALL BAG AND COVER SUPPORT INSTALL COVER ASSEMBLY 1 Install the bag and cover support B Figure 7 to 1 Attach cover assembly B Figure 9 to bag upright support A using reinforcement plate C support bracket A using hinge pivots E Secure and 3 8 16 x 1 capscrews D and 3 8 16 locknuts cover using cover hinge pins C and hair pins D E as shown as shown Figure 7 Install Bag and Cover Support Figure 9 Install Cover Assembly A Upright Support A Bag Support Bracket B Bag and cover Support B Cover Assembly C Reinforcement Plate C Cover Hinge Pins D Capscrews 3 8 16 x 1 D Hair Pins E Locknuts 3 8 16 E Hinge Pivots INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY 1 Attach hitch and upright support assembly A Figure 8 to frame spacers B as shown Figure 8 Attach Hitch and Upright Support A Hitch and Upright Support Assembly B Frame spacers INSTALL COLLECTOR BAGS 1 Raise the cover A Figure 10 2 Attach collector bags B using grass bag hanger C to bag hanger post D Figure 10 Install Collector Bags A Cover B Collector Bag C Grass Bag Hanger D Bag Hanger Posts INSTALL LOWER DISCHARGE CHUTE 1 2 Note Locknut C is intended to keep wing nut B permanently
Download Pdf Manuals
Related Search