Blaupunkt CAMBRIDGE RCR 45 User's Manual
Contents
1. does not light up the radio will also pick up weaker distant stations high sensitivity To switch over Press lo or dx On top of this the sensitivity levels can be adjusted separately for lo and dx see chap ter DSC programming Switching from stereo to mono FM If reception is poor you may get better sound quality by switching to mono Press the lo button for approximately 2 seconds With mono playback the stereo sign D will disappear from the display Each time the radio is switched on stereo playback is activated The unit will automatically switch to mono if the received signal is not strong enough for stereo playback Receiving traffic programme stations with RDS EON Many FM broadcasters offer traffic messa ges for their service area at regular intervals Alltraffic programme stations transmit a spe cial carrier signal alongside their program mes which is decoded by your car radio If this signal is identified TP will appear in the display Traffic Programme In addition to these there are also stations which do not actually transmit traffic pro grammes themselves but by using RDS EON they offer the possibility to receive the traffic messages broadcast by another traffic programme station in the same radio net work If you listen to one of these stations e g NDR3 TP will appear in the display provided the priority for traffic programme stations has been activated i e2. lt Press the desired preset button until the radio resumes play after the muting takes approximately 2 seconds confir med by beep Now the station has been stored The activated preset button is indicated in the display Notice Should you tune in a station which has alrea dy been stored before the corresponding preset button andthe memory bank will briefly flash in the display if you have selected another memory bank 25 ENGLISH Automatically storing the stron gest stations with Travelstore You can automatically store the six most powerful FM stations of your current recepti on area sorted according to their signal strength This function is particularly conve nient on longer trips Press the FMT button for more than 2 seconds The radio will search for the strongest FM stations and store them on the memory bank T Travelstore When this process has been completed the radio will play the first station If desired stations can also be stored manu ally on the Travelstore bank see Storing stations Recalling stored stations You can recall any stored station atthe touch of a button Select the waveband by pressing FMT or MeL On FM also choose the corre sponding memory bank by pressing the FMT button as many times until the desired bank appears in the display Press the corresponding preset button briefly to recall the station 26 Scanning stored stations with Preset Scan
3. You can have all of the stored stations played briefly on all wavebands On FM you can scan the stations of the Travelstore memory bank or of the two other storage levels Select the waveband lt On FM choose Travelstore or another memory bank using the FMT button To start Preset Scan lt Press PS The stations will be played for approximately 8 seconds each The positions blinking in the display show you the memory bank and preset position of the currently scanned station To select a station currently being scanned and switch off Preset Scan e Press PS briefly Scanning stations with Radio Scan Beginning with the station currently tuned in you can scan the waveband The radio will play each station for 8 seconds To start the scan Press SC briefly The scanned frequency or the station name will start flashing in the display During the actual scanning process SCAN will be displayed To select a station currently being scan ned and switch off the scan function Press SC briefly If no station is selected the scan function will be automatically switched off after the fre quency band has been run through comple tely The unit will tune in the station listened to before starting the scan Selecting the seek tuning sensi tivity You can alter the automatic seek tuning sensitivity If lo is displayed the radio will only pick up strong local stations low sensitivity If lo
4. ZG BLAUPUNKT deg 4 For this introduce the KeyCard into the slot with the contact area showing up KeyCard tongue pulled out Read also the information under Key Card theft protection system Flashing KeyCard tongue When the car radio is turned off the KeyCard tongue can be switched to flash for extra anti theft protection This feature can be switched on and off via DSC LED Rocker switch Seek tuning A Up v Down lt lt gt gt Up down in short intervals AF must be switched off lt lt gt gt To scroll through the broadcasting network when AF is activated e g NDR1 NDR4 Extra functions In the DSC mode Select and programme DSC functions Important notes Precautions Before starting to use your new car radio please read the information on Traffic safe ty and KeyCard theft protection System carefully Traffic safety As the driver of a motor vehicle it is your responsibility to pay attention to the traffic situation at all times Never use your car radio in a way that could distract you Please keep in mind that you travel a di stance of 14 m per second at a speed of only 50 km h Should the traffic situation become particu larly demanding we advise you notto use the radio Always make sure that you are still able to hear any warning signals coming from outsi de of the vehicle such as police or fire engine sirens so that you can reac
5. TA must be displayed If a traffic announcement is broadcast the radio will automatically switch to the linked traffic programme station in this case NDR2 for the duration of the message and return to the original programme NDR3 afterwards Traffic announcement priority on off If the priority for traffic announcement pro grammes is activated TA will light up in the display To switch the priority on or off Press the TA button When pressing TA while a message is being broadcast this message will be interrupted The unit will then switch back to the previous condition The priority for other traffic messa ges remains active Warning beep If you leave the reception area of the traffic programme station currently tuned into you will hear a warning beep after approximately 30 seconds This alarm tone will also be released when pressing a preset button which has no traffic programme allocated to it Switching the warning beep off a Tune into another station offering traffic information Press the rocker switch or lt a preset button which has a traffic programme station allocated to it Alternatively b Switch off the priority for traffic an nouncements Press TA TA will disappear from the display 27 ENGLISH Automatic seek tuning start tape operation When leaving the reception area of the tuned in traffic programme station while listening to a tape the system will aut
6. Radio Cassette Verona RCR 45 Operating instructions Niet NIS FMr S5 ge AF TETALI Spier eg EE BLAUPUNKT Bosch Gruppe i Uff d di d FMTS oar TP TLD FEA AN A9 Contents Short instructions 18 Important notes 21 Precautions sasinan aaa a A nad Aa 21 Traffic safety aa 21 Installation Connection 22 KeyCard theft protection system 22 Putting the unit into operation 22 Removing the KeyCard 22 Defining a second KeyCard Replacing a KeyCard 22 Displaying the radio pass data 23 Optical indication for extra security 23 Radio operation with RDS 24 AF Alternative frequency 24 REG regional programme eeeseeeees 24 Selecting a waveband 24 Automatic tuning 24 Manual tuning o e 25 Scrolling through the broadcasting network only FM eeens 25 Changing the memory bank FM 25 Storing stations a 25 Automatically storing the strongest stations with Travelstore 26 Recalling stored stations 26 Scanning stored stations with Preset Scan aaa 26 Scanning stations with Radio Scan 26 Selecting the seek tuni
7. a wrong KeyCard is inserted then CARD ERR will appear in the display In this case please do not go on operating the set After approximately 10 seconds the display will show TURN OFF Now turn off the set When inserting a card of a different kind like for example a credit card the display will show WRONG KC for approximately 2 se conds Remove the wrong card and turn off the set Do not make further adjustments until you have a correct KeyCard available Removing the KeyCard Never pull out the KeyCard directly First press the KeyCard in This releases the card and puts it in the proper position for being removed lt Now you can pull it out Defining a second KeyCard Replacing a KeyCard While operating the unit with the first Key Card you can define a second one to be also used with the set Insert the first KeyCard and turn on the set Press the DSC button and select LEARN KC with A V The display will switch to CHANGE Press the KeyCard in which releases the card and puts it in the proper positi on for being removed e Remove the first KeyCard and insert the new one while CHANGE is still being displayed Now you can also use the new KeyCard for operating your unit A maximum of two cards can be used per set When trying to define a third one the sy stem will automatically delete the access authorisation of that KeyCard which
8. echanism cassette tapes To avoid possible problems you should not use cassette tapes longer than 60 or 90 minutes C60 C90 Store your tapes in a cool place away from dirt dust and tempera tures exceeding 50 Celsius Allow very cold tapes to warm up before playing them in order to avoid uneven tape transport After approximately 100 hours of use dust partic les collected on the playback head or roller may lead to tape run problems and sound distortions Use a head cleaning tape to remove normal dirt build up For tougher cases use a cotton swab Q Tip soaked with alcohol Do not attempt to clean by inserting a hard object into the player Specifications Amplifier Output power Tuner Wavebands FM sensitivity FM frequency response Tape player Frequency response 4 x 6 W RMS power acc to DIN 45324 3 1 or 4 x 8 W max power acc to DIN 45324 3 2 87 5 108 MHz 531 1602 kHz 153 279 kHz 1 0 uV at 26 dB signal to noise ratio 35 16 000 Hz 35 16 000 Hz Subject to modifications 31 ENGLISH 2 96 Pf Blaupunkt Werke GmbH Bosch Gruppe K7 VKD 8 622 400 492 ce
9. etween 0 to 9 0 off Each alteration of this va lue is confirmed by a beep tone of the corresponding volume You can adjust the LED to flash for extra anti theft protection LED 1 LED always flash es when the unit has been swit ched off via the ignition LED 0 No flashing Loudness When listening at a low level the Loud ness function creates a more natural sound by boosting the low frequency range LOUD 1 Low boost LOUD 6 Max boost 29 ENGLISH RM LOCAL DIS LEARN KC 30 Radio Monitor With RM ON the unit will automatically switch to the tuner whenever the casset te is fast winding RM OFF The function is switched off lo To adjust the seek tuning sensitivity for local recepti on LOCAL 1 high sensitivity LOCAL 3 low sensitivity dx To adjust the seek tuning sensitivity for distant recep tion DIS 1 high sensitivity DIS 3 low sensitivity To define a second Key Card for use with the set Please read the information under KeyCard theft pro tection system To quit the DSC programming mode and store the adjustment Press DSC If the setting remains unchanged within 8 seconds the system will automatically store the last adjustment The display will switch back to the previous condition Overview of the DSC factory settings TA VOL 14 BEEP 3 LED Code 1 LOUD WI RM OFF LOCAL 1 DIS 1 Appendix Care notes M
10. ff Press AF briefly REG REG ON REG OFF With REG ON the system will only switch to a better alternative frequency if the latter belongs to a linked station offering the same regional programme see REG regional programme To switch REG on or off Press REG until REG ON or REG OFF appears in the display BEEP tone 7 lo dx To alter the automatic seek tuning sen sitivity If lo is displayed the radio will only pick up strong local stations low sensi tivity If lo does not light up the radio will also pick up weaker distant stations high sensitivity To switch over Press lo or dx briefly For more information see chapter DSC programming Cassette removal Press amp 8 Cassette loading slot Insert tape side A or 1 up the open side facing to the right Display Radio operation A NIR I NIG 5 FMTS Ib AF TETALI 2 NDR1 NDS Station abbreviation or frequency FM Waveband T Memory bank I II T 5 Preset button 1 6 CH Stereo lo Seek tuning sensitivity AF Alternative RDS frequency TP Traffic programme identifier TA Priority for traffic programme stations LD Loudness Tape operation E a fae ath AO AF TPTALD TR1 PLAY Side 1 or 2 19 11 PROG button East winding To switch to the other side of the cassette tape Press both buttons simultaneously The display shows TR1 PLAY or TR2 PLAY Fast wind
11. g cassette playback Press FR and FF simultaneously At the end of a tape side the mechanism changes directions automatically to play the other side Autoreverse The display shows TR1 PLAY for track side 1 or A or TR2 PLAY for track 2 or B Notice If there is too much tension on the tape during playback the set may switch over by itself before having reached the end of the tape side In this case check the condition of the cassette tape Sometimes it helps to rewind it completely DSC programming DSC Direct Software Control allows you to customise certain programmable basic set tings to suit your personal needs and prefe rences and then store them The basic settings for this audio equipment were made at the factory In the following you can find an overview of these settings so that you can always reset to these if desired If you wish to alter any of the programming press DSC The display will show you the adjusted con dition Use the rocker switch to select and adjust the functions described in the following A v Select function lt lt Adjust value gt gt Adjust value TA VOL To adjust the traffic an nouncement volume from between 1 to 9 The mes sage will then come through at this volume 1 low BEEP LED code LOUD Confirmation tone for all functions which require a button to be pressed for more than 2 seconds The volume can be adju sted from b
12. hed off the system will automatically shut down after one hour in order to avoid that the battery goes flat LD Loudness When listening at a low level the Loudness function creates a more natural sound by boosting the low frequency range To switch the Loudness on off Press LD For more information read chapter DSC programming 3 AUD GEO AUD To adjust the treble and bass frequen cies with the rocker switch A _ Treble w Treble lt lt Bass gt gt Bass GEO To adjust the balance left right and fader front rear with the rocker switch A Fader front v Fader rear lt lt Balance left gt gt Balance right To alter a setting e press AUD or GEO and then chan ge the value with the rocker switch The adjusted value is indicated in the display The last setting will be stored automati cally To finish the setting Press AUD or GEO If the setting remains unchanged within 8 seconds the display will switch back to the previous condition 4 DSC Direct Software Control Use the DSC function to customise certain programmable basic settings to suit your personal needs and prefe rences See chapter DSC pro gramming for more information AF Alternative frequency during RDS operation When AF lights up in the display the radio will automatically search for a frequency offering better reception of the same RDS programme To switch AF on o
13. ing FR Fast rewind stop by pressing FF FF Fast forward stop by pressing FR 12 SC Radio operation Scan sampling all stations to be recei ved Press SC briefly 20 G3 PS Preset Scan sampling all stations stored on the preset buttons Press PS briefly 1 2 3 4 5 6 preset buttons You can store six stations on each FM memory bank I Il T To store a station Press button during radio operation and hold down until the radio resumes play To recall a station Select the wave band and on FM also the desired me mory bank press FMT button as many times as required Then press the cor responding preset button briefly G5 TA priority for traffic announcements If TA is displayed the system will play traffic stations only TA on off Press button M L To select the MW or LW waveband Press button as many times until the desired band is adjusted G7 FMT FM Travelstore To switch between the FM memory banks Il and T Travelstore To switch over Press FMT as many times until the desired bank is indicated in the display To store the six most powerful stations automatically with Travelstore Store Press FMT seek tuning starts Recall Press FMT as many times until the display shows T Then briefly press one of the preset buttons 1 2 3 4 5 016 KeyCard theft protection system To operate the set it is necessary that you have inserted the KeyCard
14. ng sensitivity 26 Switching from stereo to mono FM 27 Receiving traffic programme stations with RDS EON 27 Traffic announcement priority on off 27 Warning been 27 Switching the warning beep off 27 Automatic seek tuning start 28 Adjusting the volume for traffic announcements and the warning beep 28 Tape operatioOn 28 Inserting a tape eccere 28 Removing a tape aaa 28 Fast Forward Rewind 28 PROG selector aaa 29 DSC programming 29 Overview of the DSC factory settings 30 Appendix ee 30 Care notes aan 30 Mechanism cassette tapes 30 SpecificatiOnsS 31 17 ENGLISH Short instructions Oha Off CH Volume This unit can also be switched on and off with the KeyCard 18 Also when being connected correctly you may turn the radio on and off via the ignition of your car Use one of the following possibilities to continue operating the set when the ignition is switched off a Switch on off with knob 1 b Remove insert the KeyCard c Press AUD 3 When turning on the unit with the Key Card or by pressing the AUD button the system will start to play with the volume adjusted last When operating the unit with the igniti on being switc
15. o that programme If you wish to continue listening to the first programme press the REG button REG ON appears in the display If you leave the service area of the regional programme tuned into or if you would like to take advantage of the full RDS service switch to REG OFF e Press the REG button briefly When active REG ON will be briefly dis played each time the radio is switched on Selecting a waveband With this car radio you can select between the following wavebands FM 87 5 108 MHz MW 531 1602 kHz LW 153 279 kHz Select the desired waveband by pres sing the FMT or M L button To switch between MW and LW Press MeL Automatic tuning A V Press A V the car radio will automati cally search for the next station When keeping the upper or lower part A V of the rocker switch depressed seek tuning will speed up in upwards or downwards direc tion Automatic tuning ih Ju A Up Vv Down lt lt gt gt Up down in short intervals AF must be switched off lt lt gt gt To scroll through the broadcasting network when AF is activated e g NDR1 NDR4 Manual tuning lt lt gt gt prerequisite AF is switched off e Press lt lt gt gt the frequency will change in short intervals in downwards or up wards direction When holding the right or left part of the rocker switch pressed down the frequency scan is speeded up Scr
16. olling through the broad casting network only FM You can use the lt lt gt gt buttons to tune in stations of your reception area If several programmes of one broadcasting network can be received you can scroll through them in forwards direction pressing gt gt or backwards using the lt lt button e g NDR 1 2 3 4 N JOY North German broad caster For this it is necessary that the stations have been received at least once and that AF has been activated before lights up in the dis play For this purpose you may start Travelstore seek operation Press FMT for 2 seconds the system starts to run through the frequency band If AF does not light up press AF With this the requirements for selecting sta tions with lt lt gt gt are fulfilled Changing the memory bank FM You can shift between the memory banks and T in order to store stations and recall them later The currently selected memory bank is indi cated in the display Press the FMT button as many times until the desired memory bank lights up in the display Storing stations On FM you can store six stations on the preset buttons 1 to 6 for each of the memory banks Il and T On MW LW you can store six stations each Select the waveband with FMT or MeL and on FM also the desired memory bank with FMT lt Tune in a station with the rocker switch either automatically or manually
17. omatically start searching for a new TA programme If no such station is found within approxima tely 30 seconds tape operation will be stop ped and a warning beep will sound To switch the warning beep off proceed as described above Adjusting the volume for traffic announcements and the warning beep This volume was preset at the factory You can alter the value using the DSC function see DSC programming TA 28 Tape operation Inserting a tape lt Turn on the set lt Insert a tape Insert the tape with side A or 1 showing up the open side facing to the right amp Press to eject the tape The tape will be played in the direction used last TR1 PLAY in the display means that track 1 or A is being played Removing a tape Press amp The cassette will eject Fast Forward Rewind Fast Forward Press FF At the end of a tape side the mecha nism changes directions automatically to play the other side Stopping Fast Forward operation Press FR Fast Rewind Press FR At the beginning of the tape the me chanism will automatically start play back Stopping Fast Rewind operation Press FF To switch to the other side of the cassette tape Press both buttons simultaneously The display shows TR1 PLAY or TR2 PLAY Fast winding FR Fast rewind stop by pressing FF FF Fast forward stop by pressing FR PROG selector To change the tape direction durin
18. t accordingly Therefore you should always select a mode rate volume for playing your car radio while you are driving 21 ENGLISH Installation Connection If you would like to install this equipment yourself or add any new componenis please read the enclosed installation and connec tion instructions carefully Do not connect the loudspeaker outputs to ground Use only the accessory and replacement parts approved by Blaupunkt 22 KeyCard theft protection system This car radio is supplied with one KeyCard as standard However the unit can also be operated with a second card If you have lost or damaged your KeyCard you can buy anew one from your specialised dealer When using two KeyCards you can indivi dually store the following functions Bass treble balance and fader settings assignments of preset buttons Loudness TA traffic announcement volume BEEP volume In addition to this the settings activated be fore switching the radio off such as the waveband station TA priority Loudness AF REG ON OFF and seek tuning sensitivi ty will also remained stored This ensures that the basic settings you have programmed will automatically be activated as soon as you have inserted your KeyCard Putting the unit into operation lt Turn on the set and introduce the Key Card into the slot with the contact area showing up KeyCard tongue pulled out The car radio is now ready for operation If
19. was not used for the learning process Displaying the radio pass data You can use the KeyCard supplied with the unit to display the individual radio pass data such as the model name the type number 7 6 and the serial number e Press and hold down preset buttons 1 and 6 while switching on the unit e Press the MeL button within 2 seconds The radio pass data will move through the display several times To quit the function e Press any button Optical indication for extra security When the car is stationary the KeyCard tongue can be switched to flash for extra anti theft security For this the following requirements must be fulfilled Permanent 12 V supply and the ignition lead must be connected correctly as illustra ted in the installations instructions LED 1 must be adjusted in the DSC mode Please refer to chapter DSC programming LED 23 ENGLISH Radio operation with RDS Radio Data System The Radio Data System offers you more convenience when listening to FM radio sta tions More and more radio stations have begun to broadcast RDS information alongside their programmes As soon as a programme has been identified the station name including a regional identi fier if applicable will appear in the display for example NDR1 NDS regional program me in Lower Saxony Germany When RDS is activated the station buttons become programme buttons You now know exactl
20. y which programme you have tuned into making it easy to find the desired station quickly But RDS offers you further advantages AF Alternative frequency The AF Alternative Frequency function makes sure that the strongest frequency of the currently selected programme is always tuned in automatically This function is activated when AF appears in the display In order to switch this function on or off press the AF button briefly While searching for the strongest reception signal the radio may switch to mute briefly If SEARCH appears in the display when 24 switching on the radio or recalling one of the stored frequencies the unit is automatically searching for an alternative frequency SEARCH will disappear from the display when the alternative frequency has been found or after the frequency band has been run through completely If the reception quality of the selected pro gramme becomes too bad Tune into another station REG regional programme Certain radio programmes are split up at times into regional programmes offering lo cal information The 1st programme broad cast by NDR for example offers program mes with different contents in the northern states of Germany Schleswig Holstein Ham burg and Lower Saxony at certain times of the day If you are listening to one program me and move to an area where another linked regional programme becomes stron ger the unit will switch t
Download Pdf Manuals
Related Search