Black & Decker Trimmer GL5530 User's Manual
Contents
1. Whilst holding the handle 2 rotate the head 8 anti clockwise Tighten the collar 6 by turning it anti clockwise Slide the edge guide out of the motor housing Ensure that the edging guide 9 is fully extended an audible click will be heard Note The head will only rotate in one direction Switching on and off To switch the tool on squeeze the trigger lever 1 To switch the tool off release the trigger lever Warning Never attempt to lock the trigger lever in the on position Hints for optimum use General In order to achieve optimum cutting results only cut dry grass Trimming Hold the tool as shown in fig K Gently swing the trimmer from side to side When cutting long grass work in stages from the top Take small cuts Keep the tool away from hard objects and delicate plants Cutting line will wear faster and require more feeding if the cutting is done along pavements or other abrasive surfaces or heavier weeds are being cut Ifthe tool starts running slowly reduce the load Edging Optimum cutting results are achieved on edges deeper than 50 mm Do not use the tool to create edges To create edges use an edging spade Guide the tool as shown in fig L To make a closer cut slightly tilt the tool Fitting a new spool of cutting line fig M GL4525 amp GL5028 only Replacement spools of cutting line are available from your Black 8 Decker dealer cat no A64812. Attaching the second handle fig C GL4525 amp GL5028 only Slide the second handle 5 on to the main handle 2 in an upwards direction Secure the second handle in place with the screw 13 provided Attaching the second handle fig D GL5530 only Press in and hold both of the buttons 14 on the side of the handle Slide the second handle 5 in place over the buttons 14 Warning Ensure that the teeth on the button are correctly aligned in slots in the handle and that the handle is secure Adjusting the position of the secondary handle fig E GL5530 only The second handle 5 can be adjusted to provide optimum balance and comfort Press in the button 15 on the left side od the handle Rotate the second handle 5 into the required position Release the button 15 Warning Ensure that the teeth on the button are correctly aligned in slots in the handle and that the handle is secure Adjusting the height of the tool fig F This tool has a telescopic mechanism allowing you to set it to a comfortable height There are multiple height settings To adjust the height setting proceed as follows Disconnect the tool from the supply Loosen the adjustment collar 16 by turning it clockwise Gently pull the tube 17 in or out of the handle 2 to the desired height Tighten the adjustment collar 16 by turning anti clockwise Releasing the cutting line In transit the cutting line is
3. Sono disponibili soltanto le parti evidenziate Solo estan disponibles las peizas listadas So se encontram disponiveis as pecas listadas Gedeeltelijke ondersteuning alleen de getoonde onderdelen zijn beschikbaar E16196 www 2helpU com Ya BLACK S DECKER GL4525 GL5028 Partial support Only parts shown available Nur die aufgefuerten teile sind lieferbar Reparation partielle Seules les pieces indiquees sont disponibles Supporto parziale Sono disponibili soltanto le parti evidenziate Solo estan disponibles las peizas listadas So se encontram disponiveis as pecas listadas Gedeeltelijke ondersteuning alleen de getoonde onderdelen zijn beschikbaar e 11 ZH S E16197 www 2helpU com 20 09 10 lt gt Do not forget to register your product www blackanddecker co uk productregistration Register your product online at www blackanddecker co uk productregistration or send your name surname and product code to Black amp Decker in your country Australia Black 8 Decker Australia Pty Ltd 20 Fletcher Road Mooroolbark Victoria 3138 New Zealand Black 8 Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black 8 Decker 210 Bath Road Slough Berkshire SL1 3YD 90568682 REV 2 Tel 03 8720 5100 Fax 03 9727 5940 Tel 64 9 259 1133 Fax 64 9 259 1122 Tel 01753 511234 Fax 01753 551155 Helpline 01753 574277 04 2011
4. Complete cassettes containing a spool of cutting line are also available cat no A6442 Unplug the tool Keep the tabs 18 depressed and remove the spool cover 19 from the housing 7 Original instructions a Remove the empty spool 20 from the housing Remove any dirt and grass from the spool cover and housing Take the new spool and push it onto the boss in the housing Rotate the spool slightly until it is seated Unclip the end of one of the cutting lines and guide the line into the eyelets 21 The line should protrude approx 11 cm from the spool cover Align the tabs 18 on the spool cover with the cut outs 22 in the housing Push the cover onto the housing until it snaps securely into place Warning If the cutting lines protrude beyond the trimming blade 23 cut them off so that they just reach the blade Fitting a new spool of cutting line fig N amp O GL5530 only Replacement spools of cutting line are available from your Black amp Decker dealer cat no A6481 Complete cassettes containing a spool of cutting line are also available cat no A6442 Unplug the tool Keep the tabs 24 depressed and remove the spool cover 25 from the housing 11 fig N Remove the empty spool 26 from the spool cover Remove any dirt and grass from the spool cover and housing Take the new spool and push it onto the boss in the spool cover Rotate the spool slightly until it is
5. seated Unclip the end of one of the cutting lines and guide the line into one of the eyelets 27 fig O The line should protrude approx 11 cm from the spool cover Unclip the end of the other cutting line and guide the line into the other eyelet The line should protrude approx 11 cm from the spool cover Align the tabs 24 on the spool cover with the cut outs 28 in the housing fig N Push the cover onto the housing until it snaps securely into place Warning If the cutting lines protrude beyond the trimming blade 10 cut them off so that they just reach the blade Winding new line onto an empty spool fig P R GL5530 only You may wind new cutting line onto an empty spool Replacement packs of cutting line are available from your Black amp Decker dealer cat no A6170 31 m A6171 50 m Remove the empty spool from the tool as described above Remove any remaining cutting line from the spool Feed 2 cm of cutting line into one of the holes 29 in the spool as shown fig P AAA A gt Original instructions Bend the cutting line and anchor it in the L shaped slot 30 Wind the cutting line onto the spool in the direction of the arrow Make sure to wind the line on neatly and in layers Do not criss cross fig R When the wound cutting line reaches the recesses 31 cut the line Let the line protrude approx 12 cm from the spool and hold a finger on the line to keep it in
6. taped to the spool housing Remove the tape holding the cutting line to the spool housing 7 Connecting the tool to the mains fig G Connect the female plug of a suitable extension cable to the power inlet 4 Loop the cable through the cable restraint 3 Insert the mains plug into a mains outlet For wired in cable units Make sure the cable is looped through the cable restraint prior to connecting the plug to the mains outlet Warning The extension cable must be suitable for outdoor use Use Warning Let the tool work at its own pace Do not overload Setting the tool to trimming or edging mode fig H 1 amp J The tool can be used in trimming mode as shown in fig E or in edging mode to trim overhanging grass along lawn edges and flower beds as shown in fig F Trimming mode fig H For trimming the trimmer head should be in the position shown in fig H If it is not Disconnect the tool from the supply Loosen the adjustment collar 6 by turning it clockwise Whilst holding the handle 2 rotate the head 8 clockwise Tighten the collar 6 by turning it anti clockwise Slide the edge guide 9 into the motor housing Note Note The head will only rotate in one direction H o Edging mode fig 8 J For edging the trimmer head should be in the position shown in fig If it is not Disconnect the tool from the supply Loosen the adjustment collar 6 by turning it clockwise
7. E DIRECTIVE ce GL4525 GL5028 GL5530 Black amp Decker declares that these products described under technical data are in compliance with 2006 42 EC EN 60335 1 EN 60335 2 91 2000 14 EC Lawn Trimmer L lt 50 cm Annex VIII KEMA Quality B V Utrechtseweg 310 6802 ED Arnhem The Netherlands Notified Body ID No 0344 Level of accoustic power according to 2000 14 EC Article 12 Annex Ill L lt 50 cm L measured sound power 95 dB A uncertainty K 1 dB A L guaranteed sound power 96 dB A uncertainty K 1 dB A These products also comply with directive 2004 108 EC For more information please contact Black amp Decker at the following address or refer to the back of the manual The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of Black amp Decker Kevin Hewitt 4 Vice President Global Engineering Black amp Decker Europe 210 Bath Road Slough Berkshire SL1 3YD United Kingdom 21 04 2011 Guarantee Black amp Decker is confident of the quality of its products and offers an outstanding guarantee This guarantee statement is in addition to and in no way prejudices your statutory rights The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area If a Black amp Decker product becomes defective due to faulty materials workmanship or lack of conformity within 24 months from t
8. away from the cutting line at all N times especially when switching on the motor Before using the appliance and after any impact check for signs of wear or damage and repair as necessary Never operate the appliance with damaged guards or without guards in place This appliance is double insulated therefore no earth wire is required Always check that the power supply corresponds to the voltage on the rating plate E gt Original instructions Ifthe supply cord is damaged it must be replaced by the manufacturer or an authorised Black amp Decker Service Centre in order to avoid a hazard Electric safety can be further improved by using a highsensitivity 30 mA Residual Current Device RCD Features This appliance includes some or all of the following features 1 On off switch Handle Cable restraint Power inlet Second handle Guard Spool housing Head Edge guide Assembly Warning Before assembly make sure that the tool is switched off and unplugged Fitting the guard fig A B Remove the screw from the guard Keeping the guard 6 square to the strimmer head 8 slide it into place until the retaining tab clicks into place Ensure that the guide rails 10 on the guard 6 are correctly aligned with the guide rails 11 on the strimmer head 8 fig A Secure the guard 6 with the screw 12 Warning Never use the tool unless the guard is properly fitted
9. e appliance Do not allow children or animals to come near the work area or to touch the appliance or power supply cord Close supervision is necessary when the appliance is used near children This appliance is not intended for use by young or infirm persons without supervision This appliance is not to be used as a toy Only use the appliance in daylight or good artificial light Use in a dry location only Do not allow the appliance to become wet Do not immerse the appliance in water Do not open the body casing There are not user serviceable parts inside Do not operate the appliance in explosive atmospheres such as in the presence of flammable liquids gases or dust To reduce the risk of damage to plugs or cords never pull the cable to remove the plug from a socket Safety of others This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children must be supervised to ensure that they do not play with the appliance Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings These risks can arise from misuse prolonged use etc Even with the application of the relevant safety regulations and th
10. e implementation of safety devices certain residual risks can not be avoided These include Injuries caused by touching any rotating moving parts Injuries caused when changing any parts blades or accessories Injuries caused by prolonged use of a tool When using any tool for prolonged periods ensure you take regular breaks Impairment of hearing Health hazards caused by breathing dust developed when using your tool example working with wood especially oak beech and MDF After use When not in use the appliance should be stored in a dry well ventilated place out of reach of children Children should not have access to stored appliances When the appliance is stored or transported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction Inspection and repairs Before use check the appliance for damaged or defective parts Check for breakage of parts and any other conditions that may affect its operation Do not use the appliance if any part is damaged or defective Have any damaged or defective parts repaired or replaced by an authorised repair agent Never attempt to remove or replace any parts other than those specified in this manual Original instructions a Using an extension cable Take care against injury from any device fitted for trimming Always use an approved extension cable suitable for the the filament
11. e spool and unwind the cutting line then wind it on neatly again as described above Replace the spool as instructed Maintenance Your Black amp Decker corded cordless appliance tool has been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper tool appliance care and regular cleaning Warning Before performing any maintenance on corded cordless power tools Switch off and unplug the appliance tool Or switch off and remove the battery from the appliance tool if the appliance tool has a separate battery pack Or run the battery down completely if it is integral and then switch off Unplug the charger before cleaning it Your charger does not require any maintenance apart from regular cleaning Regularly clean the ventilation slots in your tool appliance and charger using a soft brush or dry cloth Regularly clean the motor housing using a damp cloth Do not use any abrasive or solvent based cleaner Regularly clean the cutting line and spool using a soft brush or dry cloth Regularly use a blunt scraper to remove grass and dirt from the underneath of the guard Protecting the environment X Separate collection This product must not be mm disposed of with normal household waste Should you find one day that your Black amp Decker product needs replacement or if it is of no further use to you do not dispose of it with household
12. he date of purchase Black amp Decker guarantees to replace defective parts repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless The product has been used for trade professional or hire purposes The product has been subjected to misuse or neglect The product has sustained damage through foreign objects substances or accidents Repairs have been attempted by persons other than authorised repair agents or Black amp Decker service staff To claim on the guarantee you will need to submit proof of purchase to the seller or an authorised repair agent You can check the location of your nearest authorised repair agent by contacting your local Black amp Decker office at the address indicated in this manual Alternatively a list of authorised Black amp Decker repair agents and full details of our after sales service and contacts are available on the Internet at www 2helpU com Please visit our website www blackanddecker co uk to register your new Black amp Decker product and to be kept up to date on new products and special offers Further information on the Black amp Decker brand and our range of products is available at www blackanddecker co uk Ya BLACKS DECKER GL5530 Partial support Only parts shown available Nur die aufgefuerten teile sind lieferbar Reparation partielle Seules les pieces indiquees sont disponibles Supporto parziale
13. he new plug Connect the blue lead to the neutral terminal Warning No connection is to be made to the earth terminal Follow the fitting instructions supplied with good quality plugs Recommended fuse 5 A Troubleshooting If your tool seems not to operate properly follow the instructions below If this does not solve the problem please contact your local Black amp Decker repair agent Warning Before proceeding unplug the tool Appliance runs slowly Check that the spool housing can rotate freely Carefully clean it if necessary Check that the cutting line does not protrude more than 11 cm from the spool housing If it does cut it off so that it just reaches the line trimming blade Automatic line feed does not work Keep the tabs depressed and remove the spool cover from the housing Pull the cutting line until it protrudes 11 cm from the housing If insufficient cutting line is left on the spool install a new spool of cutting line as instructed above Align the tabs on the spool cover with the cut outs in the housing Push the cover onto the housing until it snaps securely into place f the cutting line protrudes beyond the trimming blade cut it off so that it just reaches the blade If the automatic line feed still does not work or the spool is jammed try the following suggestions Carefully clean the spool cover and housing Remove the spool and check if the lever can move freely Remove th
14. line length After extending new cutter line power input of this appliance see technical data The always return the machine to its normal operating position extension cable must be suitable for outdoor use and marked before switching on accordingly Up to 30 m of 1 5 mm2 HO5VV F extension cable Always ensure that the ventilation slots are kept clear of can be used without loss of product performance Before use debris inspect the extension cable for signs of damage wear and Do not use the lawn trimmer edge trimmer if the cords ageing Replace the extension cable if damaged or defective are damaged or worn When using a cable reel always unwind the cable completely Keep extension cords away from cutting elements Additional safety instructions for grass trimmers Labels on appliance Warning Cutting elements continue to rotate after the motor The following warning symbols are found on the appliance is switched off Be familiar with the controls and the proper use of the appliance Before use check the power supply cord and extension cord for signs of damage ageing and wear If a cord becomes damaged during use disconnect the cord from the mains supply immediately DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY Do not use the appliance if the cords are damaged or worn Wear stout shoes or boots to protect your feet Wear long trousers to protect your legs Before using the appliance check that your c
15. place fig Q Proceed as described above to fit the spool on the tool Warning Only use the appropriate type of Black amp Decker cutting line Winding new line onto an empty spool fig S U GL4525 amp GL5028 only You may wind new cutting line onto an empty spool Replacement packs of cutting line are available from your Black amp Decker dealer cat no A6440 Remove the empty spool from the tool as described above Remove any remaining cutting line from the spool First wind new line onto the uppermost part of the spool Feed 2 cm of cutting line into one of the slots in the upper section of the spool as shown Wind the cutting line onto the spool in the direction of the arrow Make sure to wind the line on neatly and in layers Do not criss cross When the wound cutting line reaches the recesses 32 cut the line Temporarily park the line in the slots 33 on one side of the spool as shown Repeat the above procedure for the second cutting line on the lower section of the spool Park the line in the unused slots 33 Proceed as described above to fit the spool on the tool Do not forget to release the cutting line from the parking slots 33 Warning Only use the appropriate type of Black amp Decker cutting line Mains plug replacement U K amp Ireland only If a new mains plug needs to be fitted Safely dispose of the old plug Connect the brown lead to the live terminal in t
16. utting path is free from sticks stones wire and any other obstacles Only use the appliance in the upright position with the cutting line near the ground Never switch the appliance on in any other position Move slowly when using the appliance Be aware that freshly cut grass is damp and slippery Do not work on steep slopes Work across the face of I A slopes not up and down Oo Es y gt Never cross gravel paths or roads while the appliance is running Never touch the cutting line while the appliance is running Do not put the appliance down until the cutting line has come to a complete standstill z Use only the appropriate type of cutting line Never use a metal cutting line or fishing line 96 Be careful not to touch the line trimming blade Read the manual prior to operation Wear safety glasses or goggles when operating this appliance Wear suitable ear protectors when operating this appliance Always remove the plug from the socket before inspecting a damaged cable Be careful not to use your strimmer if the cable is damaged Beware of flying objects Keep bystanders away from the cutting area Do not expose the appliance to rain or high humidity Directive 2000 14 EC guaranteed sound power Take care to keep the mains cable away from the cutting Electrical safety line Always be aware of the position of the cable Keep hands and feet
17. waste Make this product available for separate collection Separate collection of used products and packaging allows materials to be recycled and used again Re use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials Local regulations may provide for separate collection of electrical products from the household at municipal waste sites or by the retailer when you purchase a new product Black amp Decker provides a facility for the collection and recycling of Black amp Decker products once they have reached the end of their working life To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf You can check the location of your nearest authorised repair agent by contacting your local Black amp Decker office at the address indicated in this manual Alternatively a list of authorised Black amp Decker repair agents and full details of our after sales service and contacts are available on the Internet at www 2helpU com Original instructions gt Technical data GL4525 GL5028 GL5530 Type 1 Type 1 Type 1 No Load Speed 7300 7200 7300 me o ze afz Hand arm weighted vibration value according to EN 786 2 5 m s uncertainty K 1 5 m s L sound preasure 81 dB A uncertainty K 1 A gt Original instructions EC declaration of conformity MACHINERY DIRECTIVE OUTDOOR NOIS
18. y GL4525 GL5028 GL5530 gt Original instructions Intended use Your Black amp Decker trimmer has been designed for trimming and finishing lawn edges and to cut grass in confined spaces This appliance is intended for consumer use only Safety instructions Warning When using mains powered appliances basic safety precautions including the following should always be followed to reduce the risk of fire electric shock personal injury and material damage Warning When using the machine the safety rules must be followed For your own safety and bystanders please read these instructions before operating the machine Please keep the instructions safe for later use Read all of this manual carefully before operating the appliance The intended use is described in this manual The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury Retain this manual for future reference Using your appliance Always take care when using the appliance Always use safety glasses or goggles Never allow children or people unfamiliar with the instructions to use th
Download Pdf Manuals
Related Search