Avaya 4600 Series IP Telephones Application Note
Contents
1. AVAYA Avaya Solution amp Interoperability Test Lab Application Notes for Extreme Networks Alpine 3808 Power over Ethernet PoE with Avaya 4600 Series IP Telephones and Avaya Wireless Access Points Issue 1 0 Abstract These Application Notes describe the procedures for configuring the Extreme Networks Alpine 3808 to provide inline Power over Ethernet PoE to Avaya 4600 Series IP Telephones and Avaya Wireless Access Points During compliance testing Avaya IP Telephones and Wireless Access Points successfully obtained power and transferred data over standard Ethernet cables from an Alpine 3808 equipped with an Alpine FM 32Pi PoE Module Information in these Application Notes has been obtained through compliance testing and additional technical discussions Testing was conducted via the DeveloperConnection Program at the Avaya Solution and Interoperability Test Lab RL Reviewed Solution amp Interoperability Test Lab Application Notes 1 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc 1 Introduction Power over Ethernet PoE allows both power and data to be simultaneously carried over standard Ethernet cables PoE enabled Ethernet switches can supply power directly to Ethernet devices thereby simplifying installation and removing the need for separate power supplies for those devices The IEEE 802 3af standard defines the mechanisms for Power Sourcing Equipment PSE such as PoE enabled Etherne2. support extremenetworks com 7 Conclusion These Application Notes describe the steps for configuring the Extreme Networks Alpine 3808 to provide inline Power over Ethernet PoE to the Avaya PDs namely Avaya 4600 Series IP Telephones and Avaya Wireless Access Points During compliance testing the Avaya PDs simultaneously obtained power and transferred data over standard Ethernet cables from the Alpine 3808 8 Additional References Product documentation for Avaya products may be found at http support avaya com Product documentation for Extreme Networks products may be found at http www extremenetworks com services documentation RL Reviewed Solution amp Interoperability Test Lab Application Notes 9 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc 2004 Avaya Inc All Rights Reserved Avaya and the Avaya Logo are trademarks of Avaya Inc All trademarks identified by and are registered trademarks or trademarks respectively of Avaya Inc All other trademarks are the property of their respective owners The information provided in these Application Notes is subject to change without notice The configurations technical data and recommendations provided in these Application Notes are believed to be accurate and dependable but are presented without express or implied warranty Users are responsible for their application of any products specified in these Application Notes Please e mail any
3. 08 PoE doc backup to the external power source Note that the internal power supply provides up to 32 Watts to the Alpine FM 32Pi PoE Module configure inline power backup source internal slot 5 Enter the commands show inline power configuration slot lt slotlist gt and show inline power configuration ports lt portlist gt to verify that PoE support is enabled on a slot and ports on a slot respectively A ktprne oOo shy ot SiO Wweckiubinie OWS ae OMmiuc iliac EikOie 6 RO less oor E Tae Cro POU Backup PSUTActIive Usage TAre nola Watchdog 5 Enabled Internal External 710 enabled Alpine oUo Vora AOW IMS DOW CoM FoU ra MOM Wome Sie wl oa OE CONE EG Detect RSve Pwr Opr ime Viol Prec Label Sra enabled auto Cre 15 4 advertised class rae enabled auto Ore ieor advertised class Seo enabled auto Chil 15 4 advertised class 5 4 enabled auto Cee 15 4 advertised class DO enabled auto Oe ior advertised class Sale enabled auto Clade 15 4 advertised class ore ul enabled auto Cau ar A advertised class See enabled auto BRG Poc advertised class GRS enabled auto Cra 15 4 advertised class Slee enabled auto Ore 15 4 advertised class Dov lull enabled auto Ore 15 4 advertised class Sree enabled auto OTO Ers advertised class o ais enabled auto Ora 15 4 advertised class Sled enabled auto Geng 15 4 advertised class Seales enabled auto Org Reo advertised class Dako enabled auto Chia por advertised class Enter the command show inline power
4. g Glans S 49 8 64 24 8 Se None 5 4 delivering class3 4 49 8 sie 24 4 G0 None Boe delivering class3 G 49 8 n 24 0 6x00 None 18 delivering class3 6 49 8 Clee 24 0 POELO None Sy delivering class 7 49 8 106 24 4 og None DO delivering class0O 8 49 8 94 24 8 4 60 None Sa delivering class0O 2 49 8 oe 24 4 4 60 None 5220 deliverang class0O IR 49 8 98 24 0 4 90 None Sei delivering elass 0 alti 49 8 ie DESC SS S10 None Sioa Chane a oes O OO 0 0 0 OP Lou None Sesion asters aie ehalae Cm N Nit O Ea 0 ORRO O00 None SAS ane ha Ce alte 0 On O org OTTO None gr Eon Eea rO Nana T e 0 0 0 O OEN OORD None Sko a Gace ai e a a 0 Org 0 O ORD None For more detailed inline power information for one or more ports enter the command show inline power info detail ports lt portlist gt 4 Interoperability Compliance Testing The interoperability compliance testing focused on verifying PoE interoperability between the Extreme Networks Alpine 3808 and Avaya 4600 Series IP Telephones and Avaya AP 4 5 6 Wireless Access Points 4 1 General Test Approach The general test approach was to connect the Avaya PDs Avaya 4600 Series IP Telephones and Avaya AP 4 5 6 Wireless Access Points to PoE enabled ports on the Alpine FM 32Pi PoE Module and verify that the PDs successfully boot To test repeatability PoE was then disabled and enabled again on the connected ports Lastly to verify that power and data can be simultaneously carried on the PoE connections ph
5. g commands configure the Alpine 3808 to allocate power based on the detected PD s advertised class for ports through 16 on slot 5 and enable PoE support on those ports by default PoE support is enabled on all PoE capable ports configure inline power violation precedence advertise class ports 5 1 5 16 enable inline power ports 5 1 5 16 Alternatively if the actual power range drawn on a PoE capable port is known then the Alpine 3808 may be configured to allocate power based on the actual maximum rather than the 802 3af power class of the detected PD on the port The following commands set the operator limit on port 17 to 5 Watts and instruct the Alpine 3808 to allocate power based on the operator limit value on port 17 Note that any PD that draws more than 5 Watts will be denied power if connected to that port Therefore the operator limit should be set to a value that accurately represents the actual power required by PDs expected to connect to that port Coni ragut Inline pOwem OPE LAr rS lame o U0O Domes ony configure inline power violation precedence operator limit ports 5 17 enable inline power ports 5 17 An external 48V power source provides power to the Alpine FM 32Pi PoE Module As shown in the following command the Alpine 3808 s internal power supply may be configured as a RL Reviewed Solution amp Interoperability Test Lab Application Notes 5 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine38
6. one calls were made from the IP Telephones and an IP Softphone on a wireless laptop accessing the network via the AP 4 5 6 4 2 Test Results All test cases completed successfully The Alpine 3808 equipped with an Alpine FM 32Pi PoE Module successfully provided inline power to the Avaya PDs Table 1 below lists the 802 3af class allocated power and measured power of the Avaya PDs when connected to the Alpine FM 32Pi PoE Module All of the IP Telephones were in idle on hook states RL Reviewed WCH 10 22 2004 7 of 10 Alpine3808 PoE doc Solution amp Interoperability Test Lab Application Notes 2004 Avaya Inc All Rights Reserved Avaya Powered Device 802 3af Class Allocated Power W Measured Power W l 4602S W 7 3 2 4610SW 2 0 0 0 ek NO Table 1 802 3af Class Allocated Power and Measured Power for Avaya 4600 Series IP Telephones and Wireless Access Points connected to Extreme Networks Alpine 3808 Table 2 below summarizes the 802 3af classes PSE Output Max Power W EE Treat as Class 0 Table 2 IEEE 802 3af Power Classifications 5 Verification Steps The following steps may be used to verify the configuration 1 Ensure that PoE has been enabled on the system the slot housing the Alpine FM 32Pi PoE Module and the ports that serve the PDs 2 Connect the Avaya PD to a PoE enabled port on the Alpine FM 32Pi PoE Module and verify that the PD powers on successf
7. questions or comments pertaining to these Application Notes along with the full title name and filename located in the lower right corner directly to the Avaya DeveloperConnection Program at devconnect avaya com RL Reviewed Solution amp Interoperability Test Lab Application Notes 10 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc
8. st Lab Application Notes 2 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc Alpine 3808 AP 4 5 6 Wireless Access Point t 4602 4602SW IP Phones a PF ai za a Generation 2 4610SW 4606 4612 4624 IP Phone IP Phones 4620 4620 EU24 4630SW Generation 1 4612 4624 4620SW 4620SW EU24 IP Phone IP Phones with 30A IP Phones Switch Base Figure 1 PoE Interoperability Between Extreme Networks Alpine 3808 with Alpine FM 32Pi PoE Module and Avaya 4600 Series IP Telephones and Avaya Wireless Access Points To line jack of 4612 4624 IP Telephone To PC To ethemet switch port Figure 2 30A Switch Base for Generation 1 Avaya 4612 and 4624 IP Telephones RL Reviewed Solution amp Interoperability Test Lab Application Notes 3 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc 2 Equipment and Software Validated The following equipment and software firmware were used for the sample configuration provided Equipment Software Firmware Avaya S8500 Media Server running Avaya 2 1 RO12x 01 0 411 7 Communication Manager Avaya G650 Media Gateway TN2312BP IPSI Avaya 4602S W IP Telephone 1 8 2 TN799DP C LAN Avaya 4620SW IP Telephone Avaya 4620SW IP Telephone with EU24 Avaya 4630SW IP Telephone Avaya 4624 IP Telephone Generation 2 1 8 2 Avaya AP 4 5 6 Wireless Access Point Avaya IP Softphone Extreme Net
9. t switches to detect classify and supply power to Powered Devices PDs such as PoE enabled IP telephones and wireless access points In the compliance tested configuration described in these Application Notes an Extreme Networks Alpine 3808 equipped with a 32 port Alpine FM 32Pi PoE Module is a PSE configured to supply inline PoE to Avaya PDs specifically Avaya 4600 Series IP Telephones and Avaya AP 4 5 6 Wireless Access Points As illustrated in Figure 1 the Avaya PDs covered in these Application Notes include the following 4602 IP Telephone 4602S W IP Telephone 4610SW IP Telephone 4620 IP Telephone with and without EU24 expansion module 4620SW IP Telephone with and without EU24 expansion module 4630S W IP Telephone Generation 1 4612 IP Telephone with 30A Switch Base Generation 1 4624 IP Telephone with 30A Switch Base Generation 2 4606 IP Telephone Generation 2 4612 IP Telephone Generation 2 4624 IP Telephone AP 4 5 6 Wireless 802 1 1a b g Access Point The Avaya Generation 1 and Generation 2 4612 and 4624 IP Telephones are distinguishable by their model numbers For example the model number 4612D01A 003 indicates Generation 1 while the model number 4612D02A 003 indicates Generation 2 The 30A Switch Base shown in Figure 2 is required for the Avaya Generation 1 4612 and 4624 IP Telephones to be powered by PoE RL Reviewed Solution amp Interoperability Te
10. to view the inline power information for the Alpine 3808 system Alpine3808 273 show inline power Inline Power System Information System maximum inline power 334 watts Power Usage 70 233 watts S here Marot Po Urota TUS PackUp UE E US Firmware Status 5 ON Present DEACTIVATED Operational Enter the command show inline power slot lt slotlist gt to view the inline power information for a slot The output below indicates that 141 2 Watts has been allocated to connected PDs on the slot and the actual total power consumption of those PDs is 57 8 Watts Alpine3808 274 show inline power slot 5 Common Power Reserved Power Silene Configured Allocated Configured Allocated Measured usage 5 334000mW 141200mW O mW 0 mW 57800mW RL Reviewed Solution amp Interoperability Test Lab Application Notes 6 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc Enter the command show inline power info ports lt portlist gt to obtain inline power information for one or more ports The output of the command displays the inline power state detected 802 3af class actual power consumption and fault state on each specified port PulodkteS OO Ci oe eS hlOwe em Mine pO OMmes sinter jso Or as orl of due Port State Class Connect Volts CULE Res Power Pavele HBL TIS OMe V7 mA Kohms Watts gal delivering class al Seal OW goes Oe Steele None Sore delivering class2 2 SOS OW ae Sieve Se AU None Dee deliverin
11. ully If the PD does not power on enter the command show inline power info detail ports lt portlist gt 3 Ifthe output shows that the Inline Power State is discovered then disable inline power on the port enter the command configure inline power detection auto ports lt portlist gt and re enable inline power on the port RL Reviewed Solution amp Interoperability Test Lab Application Notes 8 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc 4 If the output shows that the Inline Power State is denied then there is insufficient available power to power the PD 5 For the Avaya 4600 Series IP Telephone verify that it successfully registers with Avaya Communication Manager and completes phone calls to other phones assumes the IP telephone has been configured with the correct IP and call control information 6 For the Avaya Wireless Access Point verify that an Avaya IP Softphone running on a wireless laptop accessing the network via the Access Point successfully registers with Avaya Communication Manager and completes phone calls to other phones assumes the IP softphone has been configured with the correct IP and call control information 6 Support For technical support on Extreme Networks products consult the support pages at http www extremenetworks com services or contact the Extreme Networks Worldwide TAC at e Toll free 800 998 2408 e Phone 408 579 2826 e E mail
12. works Alpine 3808 with FM 32Pi PoE ExtremeWare Module 7 2 0 Build 33 RL Reviewed Solution amp Interoperability Test Lab Application Notes 4 of 10 WCH 10 22 2004 2004 Avaya Inc All Rights Reserved Alpine3808 PoE doc 3 Configure Inline Power over Ethernet on the Extreme Networks Alpine 3808 Inline Power over Ethernet PoE is supported on the Alpine 3808 with addition of the Alpine FM 32Pi PoE Module By default PoE support is enabled on the system and on all slots The following commands can be used to explicitly enable PoE support on both the system and a slot containing an Alpine FM 32Pi PoE Module enable inline power enable inline power slot 5 Each PoE capable port automatically detects 802 3af compliant Powered Devices PDs and may be configured to also supply power to detected PDs The following command allows ports 1 through 16 on slot 5 to detect and supply power to PDs configure inline power detection auto ports 5 1 5 16 Inline power budgeting in the Alpine 3808 is based on allocated power not actual power consumption For example a detected PD may be allocated 15 4 Watts even though it may actually consume less than that The Alpine 3808 can be configured to allocate power on a PoE capable port based on the 802 3af class of the detected PD the configured maximum power on the port the greater of the class power and configured maximum power on the port or the maximum allowed power on the port 20 Watts The followin
Download Pdf Manuals
Related Search