Audiovox P-150 User's Manual
Contents
1. by AUDIOVOX COMPACT DISC CHANGER SYSTEM WISE M PACKING LIST MAIN UNIT Changer ee a BA ve INSTALLATION PARTS Bracket L Bracket R Hexagonal bolt with washer 5 Meter Din Cable M5 x 10 4 pcs 1 pc Self tapping screw Seals A Seals B M5 x 12 KES S o OES eS 4 pcs 1 pe 1 pe OTHER ACCESSORIES CD Magazine Index seal sheet Installation Manual Owner s guide SS 1 pc 1 pc 1 pc BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is locked into place during shipment by the transport screws Be sure to remove the screws prior to installation Caution After removing the transport lock screws place the supplied seals A over the screw holes These seals are used to keep dust out of the unit which could cause a malfunction Installation and Wiring Precautions 1 To prevent a short circuit Be sure to turn off the ignition and remove the negative battery cable prior to installation Connect power wires last Note If the changer is to be installed in a car that is equipped with an on board drive or navigation computer do not disconnect the battery cable Ifthe cable is disconnected the computer memory may be lost Under these conditions use extra caution during installation not to cause a short circuit 2 Do not install the unit in the following locations Locations exposed to direct sunlight Where hot air is discharged from the2. R to each side of the unit using the hexagonal bolts with washer base M5 x 8 EN Anti vibration N B springs position i fes e X v NOTE Use seals A to cover unused mounting holes on sides of unit Bracket L with washer base M5 x 8 2 Determine the mounting location and drill four mounting holes Never mount the unit near the fuel tank Drill holes 4mm in diameter 3 Secure the unit in place using four self tapping screws M5 x 12 Use RTV silicone sealer on screw threads or around the holes to prevent moisture intrusion Bracket L PROCEDURE FOR VERTICAL INSTALLATION Note If the anti vibration spring position has been changed and verified for vertical mounting as shown on page 3 start with step 2 1 Set the 4 anti vibration springs to position V 2 Attach bracket L and bracket R to each side of the unit using the hexagonal bolts with washer base M5 x 8 NOTE Use seals A to cover unused mounting holes on sides of unit position V Bracket L Bracket R Hexagonal bolt with washer base M5 x 8 3 Determine the mounting location and drill four mounting Mount the unit in place using four self tapping screws holes M5 x 12 Use RTV silicone sealer on screw threads or around the holes to prevent moisture intrusion Never mount the unit near the fuel tank Self tapping screw M5 x 12 Bracket L Drill holes 4 mm in diam
3. car heater In areas subject to extreme temperatures Incorrect installation can cause the sound to skip when playing a disc Mount the unit firmly in place using the supplied brackets and screws Be careful not to damage the car wiring Be sure to use the supplied screws Be careful not to snag any wires when tightening screws Do not use any of the screws that are part of the brake or steering system to install the unit cO A 6 This unit cannot be installed on its side end or upside down Installation in such positions will cause malfunctioning of the mechanism INSTALLATION The unit can be installed horizontally vertically or at a 45 angle The position of the built in anti vibration springs left and right side must correspond to the mounting position chosen If the springs are not set correctly for the type of installation chosen the anti vibration compensation will not be effective and vibration may cause the disc to skip CAUTION After setting the built in anti vibration springs place the supplied Seals B over the holes These seals are used to keep dust which could cause a malfunction out of the unit HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45 ANGLE INSTALLATION Set the 4 anti vibration springs to Set the 4 anti vibration springs to Set the 4 anti vibration springs to position H position V position 45 position H position 45 position V Attach bracket L and bracket
4. eter PROCEDURE FOR 45 ANGLE INSTALLATION Note If the anti vibration spring position has been changed and verified for 45 angle mounting as shown on page 3 start with step 2 M Set the 4 anti vibration springs to position 45 2 Attach bracket L and bracket R to each side of the unit using the hexagonal bolts with washer base M5 x 8 NOTE Use seals A to cover unused mounting holes on sides of unit position 45 Bracket L Bracket R Hexagonal bolt with washer base M5 x 8 Determine the mounting location and drill four mounting 4 Mount the unit in place using four self tapping screws holes M5 x 12 Use RTV silicone sealer on screw threads or around Never mount the unit near the fuel tank the holes to prevent moisture intrusion Self tapping screw M5 x 12 Drill holes 4mm in diameter Bracket L Bracket R VEHICLE WIRING Mating 8 pin DIN socket on rear of compatible radio chassis see note 1 below Car Stereo with CD Changer Controls CD changer NOTE 1 Check with your Prestige car audio dealer to be sure your stereo is directly compatible with this CD changer 2 Wiring instructions for use with FM Modulator Commander Systems are included with the P MC3 and P MCR4 accessories 1997 AUDIOVOX CORP HAUPPAUGE N Y Printed in Korea Form No 128 5203
Download Pdf Manuals
Related Search