Audiovox CHRYNAV1 Installation Manual
Contents
1. Exit Navigation by Long press again or selecting EXIT from the navigation menu on screen NOTE Exit cancels your current route On vehicles with the 4 3 screen use the MORE button to select the Navigation source Exit Navigation by pressing again or selecting EXIT from the navigation menu on screen a ma 10 10 ws Ye F 89 9 101 9 94 7 103 3 all 101 9 AM SAT tune audio info For Navigation operation see the included quick start guide or download a full user s manual from WWW ADVENTPRODUCTS COM If the picture is not centered or does not fill the screen correctly you can adjust the picture size Access the settings menu by pressing the Menu button on the side of the Nav Interface Module Use the Menu button to scroll through the options and or buttons to adjust the value Contrast Brightness and Saturation are all screen adjustments for picture quality Position H and V are for Horizontal and Vertical Position use to adjust to fit factory screen as needed IR AV1 IR AV2 NOT USED Select NONE to insure proper operation Guide L Guide R CNTRL These are controls for the position of the Parking Lines By selecting or you can move the position of the lines to match the vehicle width 5 H Size V Size This will adjust the picture to meet the full screen size of the OEM panel mn Setup Menu Contrast Brightness Saturation Position H Position V NOT USED NOT USED SS sr 02. vehicle is equipped with this If you are adding a camera or aux Inputs use the supplied cables and connect as needed 7 Aux Video Aux Audio See attached labels 6 Aux Video Red Backup Camera Input Yellow Aux 1 Video Input White Aux 2 Video Input Gray Not used 8 USB Update Cable This is used for map updates Route the cable from the module to the glove box for future use as needed Connect to the Nav module 9 GPS Antenna The antenna must be mounted in a location where it has a clear view of the sky Center of the dash by the glass is recommended NOTE If reception is poor re locate to another area and re test The GPS antenna cannot be blocked by metal surfaces and should be visible for best reception DIP Switch Settings Up is OFF Down is ON for Dip Switches 10 Check the DIP Switch settings Dip 1 UP External RGB input Not used Dip 2 UP Video Input 1 Off Dip 3 UP Video Input 2 Off Dip 4 DOWN OEM High Resolution Monitor On Dip 5 UP Up OEM Camera DWN After Market Camera Dip 6 UP This is not used Dip 7 UP This is not used Dip 8 UP For 8 4 screen Down for 4 3 screen 11 Check to be sure the Map SD Card is installed in the Navigation unit Double check all connections and then reconnect the vehicle battery Navigation Interface Operation To change the OEM radio to Navigation Mode Long press the Voice Activation Key on the steering wheel Press again to cancel voice prompt
3. Guide R Guide CNTRL Specifications No Name Parameters 1 Videoinput Vp with 75 Q impedance y Synchronized signal strength 3 5Vpp with 5K impedance negative pulse synchronization RGB resolution By changing DIP4 user can select HD VGA or normal HD 800X480 or VGA 640X480 Normal NTSC vertical 240 or 234 A Av1 Av2 cam video 0 7Vpp with 75 Q impedance 5 Av1 Av2 cam format NTSC PAL SECAM Automatic switch s remore Tari Trigger level threshold Reverse and gt 5V trigger switching Output current of additional control Maximum current of 2A port 1 2 7 ie SI lee temperature range 40 85C 11 Dimensions 15 6 X9 2X22Cm For Technical Support Please Call 1 800 323 4815 OE Spkr or Ext Spkr A Not Used Gimer Lvos OUTPUT Navigation Interface Power Harness tor Chrysler Power from CAN box Connect to ne we B CAN box DIP Settings AUX Video 7 Vehicle Specific Instructions Tech Tips and Installation notes can be found at WWW AUDIOVOXUNIVERSITY COM NOTES NDV ENT Voxx Electronics Corporation Hauppauge NY 11788 Technical Assistance 1 800 323 4815 WWW ADVENTPRODUCTS COM 2014 Printed in China 128 9395
4. MANN ENT CHRYNAV1 Advent Integrated Navigation This interface is designed to integrate Navigation into select Chrysler and Dodge 8 4 or 4 3 monitors INSTALLATION MANUAL 315 7 33 26 ah y 25 8 g 80s on pr Walking On Suns 44 Katrina amp me a mio MRE FM tune browse AN What s in the Box The following items are supplied with the CHRYNAV1 lt Installation Guide Prior to Installation Care must be taken when installing this accessory to ensure damage does not occur to the vehicle The installation of this accessory should follow approved guidelines to ensure a quality installation Read entire instructions thoroughly before starting This document covers such items as e Vehicle Protection use of covers and blankets cleaning chemicals etc Vehicle Disassembly Reassembly panel removal part storage etc Electrical Component Disassembly Reassembly battery disconnection connector removal etc NOTES Removed Parts Inspect the vehicle for any damage Place all removed parts on a protected surface in an area where they will not be damaged Connectors When disconnecting connectors do not pull on the wires pull on the connectors Vehicle Preparation and Protection CAUTION e Do not touch the positive terminal with any tool when removing cable e Besure ignition key is in the OFF position during install e Donot disconnect ANY airbag connectors or indicators Doing so ma
5. be located behind the radio Determine your exact mounting location to insure you route your wires correctly 3 Disconnect the 4 pin LVDS Video cable from the touch panel Do not use the connection at the radio 4 Using the supplied LVDS connect cable connect the factory LVDS cable to the supplied cable the panel to the supplied cable and route to the Nav Module location 5 Thesystem utilizes either the left dash speaker or the included external speaker for easier installation or for vehicles that do not have dash speakers When connected to a factory speaker the Nav system will mute the radio audio in that speaker only when giving directions If using the external speaker the factory audio will not mute To install using the factory speaker remove the left dash speaker from the dash route the included speaker harness to the speaker location Connect the supplied harness to the speaker and the OEM wiring to the other harness connector Route the wire to the module and connect If using the included external speaker pick a location that is not obstructed and can be heard easily by the driver Remove the tape backing from the rear of the speaker and attach to the mounting location Route the wire to the module and connect If needed or for custom installation this can be wired to any standard 4 ohm speaker The Nav module has the ability to add a backup camera and 2 AV inputs The module will support the factory backup camera if the
6. y result in activating a diagnostic code These codes will require the dealer to perform the reset procedure and may be charged a dealer fee e Ifyou are unsure of any vehicle trim removal process consult the OEM service manual e Removing vehicle trim panels in extreme hot and cold climate could result in some vehicle damage Use care when removing all vehicle trim e Using tape on vehicle trim panels could help limit any scratches and or marring Use plastic trim panel removal tools whenever possible The instructions included in this kit are current at the time of printing It is designed as a guide to help make the installation of this product successful Always use caution and ask for assistance if you are not sure how to proceed Voxx International is not responsible for any damage that may occur during installation or any changes to the vehicle interior Installation NOTE Disconnect the vehicle battery before starting your installation Removal of the LCD Touch Panel and Radio control center is required for installation Vehicle Specific instructions are available on line at www voxxuniversity com After the components are removed connect the following 1 Using the Supplied T harness Power Cable disconnect the matching cable from the main Radio CD unit Plug the T harness in the radio and the factory harness into the T harness The small 4 pin harness on the T harness connects to the CAN module 2 The navigation module will
Download Pdf Manuals
Related Search