Aube Technologies TI032-3W User's Manual
Contents
1. 450 358 4600 Toll free 1 800 831 AUBE Fax 450 358 4650 Email aube service honeywell com For more information on our products go to www aubetech com 400 032 001 B 30 11 06 2 22. format Programs do not run as Make sure the switch is properly pro expected grammed Note that indicates an inactive pro gram 00 00 indicates midnight If the switch has been configured for 12 hour format check that PM appears on the left side of the screen when an after noon time is displayed The metal plate is hot This is normal with high loads maximum of 500 W Technical Specifications Supply 120 VAC 50 60 Hz Minimum load 40 watts Maximum load 500 watts Operating temperature range 5 F to 122 F 15 C to 50 C Storage temperature range 4 F to 122 F 20 C to 50 C Power outage The programs are protected by a rechargeable battery The screen is blank during the power outage Certifications CSA amp UL TI032 3W V Warranty AUBE warrants this product excluding battery to be free from defects in the work manship or materials under normal use and service for a period of three 3 years from the date of purchase by the consumer If at any time during the warranty period the product is determined to be defective or malfunctions AUBE shall repair or replace it at AUBE s option If the product is defective i return it with a bill of sale or other dated proof of purchase to the place from which you purchased it or ii contact AUBE AUBE will make the determination whether the product should be returned or whether a replacement product can be s
3. aube technologies Applications The TI032 3W switch can be used in a single pole or 3 way installation with the following types of lighting e Incandescent Halogen e Low voltage halogen with transformer e Fluorescent The T1032 3W switch cannot be used with a load below 40 W or above 500 W Installation Cut power at the circuit breaker to avoid electric shock Remove the existing switch For a 3 way installation identify and label the wire that is connected to the common screw Install the new switch refer to the appropriate section below 00 00 Apply power at the circuit breaker NOTE A f load See NOTE A ae Connect wires 2 and C of the T1032 3W to the line 120 V wire EXISTING 3 WAY INSTALLATION 120 VAC See NOTE A 3 wire cable Connect wire C of the T1032 3W to the common wire identified when removing the old switch Connect the other two TI032 3W wires to the two remaining wires At the other 3 way switch connect the jumper wire between the com mon screw and the screw where wire 1 of the T1032 3W is connected TI032 3W T1032 3W Installation and User Guide Programmable Wall Switch NEW 3 WAY INSTALLATION 120VAC See NOTE A The jumper wire is not required in this installation A single pole switch can be used as the other switch in a 3 way installation Power On 1 Pry the switch door open from the
4. bottom using a small screwdriver Ensure the ON OFF selector is set mesel to ON Control 4 Reset the switch using a paper clip a 0 00 and MO will flash aeia selector If the display is blank Ensure the ON OFF selector is properly engaged in the ON posi tion Push it to the right using a small screwdriver e If the programmable switch controls a lamp equipped with a built in On Off switch ensure the lamp switch is set to On Ensure the light bulb is not burned out and is tightly screwed in its socket EXISTING 3 WAY INSTALLATION If either switch does not work properly rewire the jumper between the common screw and the other screw WARNING Before replacing the light bulb place the ON OFF selector in the OFF position Failure to do so might damage the switch Setting the Clock NOTE The switch displays the time in 24 hour format by default or following a reset To change to 12 hour format or vice versa proceed as follows a Press one of the control buttons to ensure the MAN or AUTO indicator is displayed b Press the MIN and HOUR buttons simultaneously and brief tly 0 00 display 24 hour 12 00 display 12 hour Set the time using the HOUR and MIN buttons If you have selected the 12 hour format ensure that PM appears on the screen when an afternoon time is displayed Set the day by using the DAY button Press one of the control buttons or close the switch door to return to norma
5. ent to you This warranty does not cover removal or reinstallation costs This warranty shall not apply if it is shown by AUBE that the defect or malfunction was caused by dam age which occurred while the product was in the possession of a consumer AUBE s sole responsibility shall be to repair or replace the product within the terms stated above AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WAR RANTY EXPRESS OR IMPLIED OR ANY OTHER FAILURE OF THIS PROD UCT Some provinces states or regions do not allow the exclusion or limitation of incidental or consequential damages so this limitation may not apply to you THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS WARRANTY Some provinces states or regions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from one province state or region to another Z Customer Assistance If you have any questions on the product installation or operation contact us at 705 Montrichard Avenue Saint Jean sur Richelieu Quebec J2X 5K8 Canada Tel
6. l operation 00 400 032 001 B 30 11 06 1 2 Selecting the Operating Mode The programmable switch has 2 operating modes manual MAN and automatic AUTO To switch mode press the switch door for 3 seconds Manual Mode The programmable switch operates as a regular switch Briefly press the switch door to turn the lights On or Off The mode MAN and state ON or OFF are displayed m gg 5 Automatic Mode The programmable switch follows the programmed schedule The mode AUTO state ON or OFF and Aen current program number are displayed i 2 25 To temporarily override the programmed schedule w press the switch door The new state ON or OFF will flash to show that this state is temporary The override remains in effect until you press the switch door again or until the beginning of the next program Programming You can set up to 7 programs To set a program you need to enter its start time ON and its end time OFF o Pry the switch door open using a small screwdriver Press the PGM button to display a program and its On or Off time For example when you first press P PGM program number 1 P1 and its On time ON will appear will appear instead of the time if the program is not set inactive Press the DAY button to select the day to which you want to apply the program NOTE If you want to apply the program to every day of the week press DAY until all the da
7. ys are displayed This still counts as 1 program not 7 Press the HOUR and MIN buttons to set the ON time time when you want the lights to turn on If you have selected the 12 hour format ensure that PM appears on the screen when an afternoon time is displayed After you have programmed the ON time press the PGM button to display the OFF time time when you want the lights to turn off 6 Repeat steps 3 through 5 to program the OFF time If the program ON time is set for every day of p the week the program OFF time will automatically i be set for every day MO TU WE TH FR SA SU To set another program repeat steps 2 through 6 Programs that are not set will remain inactive Press one of the control buttons or close the switch door to return to normal operation MO ON P 1 i MO TU WE TH FR SA SU Clearing a Program Press the PGM button until the desired program is selected Hold the PGM button for 3 seconds appears when the program is erased Troubleshooting Blank display e Verify circuit breaker at main panel e Verify if light bulb is burned out Ensure the ON OFF selector is at ON e Reset the switch using a paper clip Faded or irregular e Load is less than 40 W display Ambient temperature is below freezing point Cannot switch between First press one of the control buttons so 24 hour format and that MAN or AUTO appears on display 12 hour
Download Pdf Manuals
Related Search