Atlas Y1878 User's Manual
Contents
1. lamp 26 Lamp Module Replacement By easy access to lamp module via latched hinged door No tools required Lamp replacement door interlocked for safety Lamp power will be cut when door is open 21 Lamp Life 500 hours to 50 of initial output specification measured through 6mm glass rod 2 1000 hours typical measured through 6mm glass rod User Interface Control 31 User Instructions Operation manual to be included with every lightsource mM 3 2 Standby Switch Located on front panel illuminated when ON Lamp ignition not automatic with standby switch ON Lamp ON OFF Switch Located on front panel Lamp ON status indicated by LED on front panel Illuminated When lamp ON button is depressed to turn lamp on the lamp on LED when lamp is ON flashes until such time as the lamp ignites If the lamp fails to ignite in approximately 4 seconds possible fault condition the system will time out and the lamp ON button will need to be depressed again to initiate lamp ignition Fiber Optic Adapter 4 port turret with WOLF STORZ ACMI OLYMPUS ports Turret rotated to select one fiber port for illumination at a time Turret rotation will be resitant enough to prevent non deliberate rotation by pulling fiber cables All light output specifications refer to system only performance Light output via optical fibers or other optical components may vary Light Attenuation Shutter Controlled by membran2. 0 clorox 90 water solution applied with a damp cloth 3 ASSOCIATED EQUIPMENT 3 1 Fiber optic light guides cables not provided by Atlas Specialty Lighting Issue x 2 17 January 2006 NS 100 240 VAC SOOFIz unversa SUA Wu I D ACPoweronmeda Locsedonreerpanedususes OOOO I gt 2 Performance Features amp Warranty Beam profile to have smooth distribution with no shadows or sharp peaks 22 Overtemperature Prorection Automatic shut down in the event of overheating Fans operate when AC power is on and are independent of lamp status 2 3 Over Heat Recovery Auto Cool Unit to become fully operational within approximately 3 minutes after thermal shut down Fans will remain on in the event of thermal shut down when power is ON amp all obstructions to air flow removed at environmental temperature of 22C 72F Lamp must be switched on by using lamp ON OFF switch located on front panel 24 Fiber Optic Connection Safety Feature Lamp will not ignite unless a fiber optic cable is fully inserted into the active port on the Fans will remain on in the absence of a fiber optic cable inserted into turret active port when power is ON Lamp power is cut or blocked if fiber optic cable is removed from active port to prevent accidental light leakage 25 Lamp Module Y1879 low profile CERMAX 300 Watt lamp module incorporating proprietary type Lamp specifications may vary slightly from standard PE300C 10F
3. N 60601 1 2 2001 CAN CSA C22 2 No 601 1 M90 R1997 B 98 S1 94 UL mark CUL mark CE mark Compliance to standards Regulatory Markings Atlas Specialty Lighting assumes no responsibility for the suitability of this lightsource for any particular application or any consequential damages associated with the use of this lightsource Issue x 2 17 January 2006 Lamp Hours ox UA D pixstar o Tue The Ultimate Um dd a y o w Cormax Xenon Fiber Optic Light Source Pi LOUEN IT TRITT LP Im a ist See ETT q
4. Y1878 Fiberoptic Illuminator 1 GENERAL SYSTEM DESCRIPTION 1 4 System Features The Y1878 300 Watt Xenon light source described herein is specifically designed for use as an illumination source for fiber optic illumination applications As a result the system shall have the following general features 1 1 1 4 port flush mount design turret for fiber optic light cable connection to fit ACMI Storz Wolf Olympus industry standard fibers 1 1 2 Simple lamp module replacement with no tools required 1 1 3 Simple power ON switch separate from the lamp ignition switch 1 1 4 Standard lamp safety features 1 1 5 Low noise generation 1 1 6 Very high brightness light output 1 1 7 Even output beam profile 1 1 8 Compact footprint 1 1 9 Quick re strike in the event that the device shuts down from overheating 1 1 10 Single world wide universal power supply 2 INTENDED USAGE 2 1 General This 300 W Xenon light source shall be used as an illumination source to provide light to fiber optic cables or light guides Atlas Specialty Lighting assumes no responsibility for suitability for any particular application of the lightsource or any consequential damages associated with the use of the lightsource 2 2 Personnel 2 2 1 Any trained personnel that has familiarized themselves with the product by reading the operation manual provided 2 3 Sterilization Disinfection 2 3 1 The light source may be wiped down with hospital approved disinfectants e g 1
5. e buttons on front panel 2 Buttons for relative intensity increments up and down 1 button for shutter fully closed 1 button for shutter fully open Relative level of illumination indicated by a digital numeric display blue numerals Lamp Hour Counter Lamp hour mode is selected while Lamp Hours button located on front panel is Lamp hour counter also records number of time the lamp hours have depressed been reset This number is displayed when lamp hours are re set While lamp hour mode is selcted the number of elapsed lamp hours will be displayed on the relative brightness display Elapsed lamp hours will be displayed up to 999 hours Elapsed lamp hours displayed can be reset by end user Mechanical amp Environmental A1 Height 5 0 x Width 16 9 x Depth 13 8 nominal Designed for modular expansion 22 5 5 5 5 5 wegipobsBigmmm E E ExeiiwsAlsSpedalyUugNngatwokam dos P a a TeTempmaueper ziii EAN clorox 90 water solution applied with a damp cloth must not be wet a OpemmgTememumpCiA E a sSempeTewewus2w RG OOOO s Opesing amp StrageHumii iO 85 relative humidiy noneondensing s o 77777777 Operating Pressure Atmosphere nominal TubeNoe ixB E Shipping ShckVimnperBSTATA E 215 CooingVenisiodredaowiwardihebackohheunt ne 9 Regulatory Approvals IEC 60601 1 1998 A1 1991 A2 1995 A1 3 1997 UL 60601 1 2003 EN 60601 1 1990 A1 1993 A2 1995 A13 1997 E
Download Pdf Manuals
Related Search