Arkon 51020 User's Manual
Contents
1. SCOOTER Installation and Operation l titut kiliu Operation 4 New Key Fob Lost Key Fob 5 Troubleshooting 6 The Acumen SCOOTER can be upgraded from the standard key fob to the CAT1 and CAT21 fob with key conversion and LED torch Contact Acumen or your Dealer Spares and Accessories 6 Wiring Diagram Back Cover Installation and Wiring The Acumen SCOOTER consists of the following main components SCOOTER main unit ECU Electronic Control Unit SCOOTER wiring harness 1x Remote Fob Fitting kit including System fuse spare fuse amp Red LED system indicator Tool Required Pliers Cable strippers Cable cutters Drill with 5 5mm and 8mm bits Soldering equipment Adhesive lines heatshrink tubing High quality insulating tape Masking tape for drilling LED hole Multimeter General workshop tools Scooter wiring diagram SCOOTER main unit ECU Electronic Control Unit Ensure the fitting of the equipment and the associated wiring does not affect the operation of the scooter Be sure the alarm and wiring does not affect moving parts such as control cables brakes and does not touch hot parts The SCOOTER is designed for scooter use and is fully encapsulated so water ingress is not of a concern Likewise the Key Fob is also of a waterproof design We recommend however that the unit is not placed in a position where it is continually subjected to water and or pressure washing Sitin2. 5 seconds and the unit will monitor hot wire accessory switch movement and nudge The system will not arm if the ignition is switched on To Disarm the system Press the Unlock button The system will give one short beep and flash the indicators once NOTE If the system gives one long beep this means the alarm has been sounding Enter diagnostics mode to find the reason why Convenience Ferry Mode In Convenience mode the movement nudge sensor will cease to function With the alarm active press the Silent button You will get one long tone and one flash of the indicators If the LED flashes once per second the movement sensing is active If the LED flashes once every two seconds the movement sensing is disabled You can toggle between Convenience Mode enabled and disabled by simply pressing the silent button Diagnostics Mode It is possible to determine the trigger source that caused the alarm to sound Only the last reason is recorded Diagnostic mode can be accessed two ways a When the alarm is sounding the LED will flash a number of times pause then flash the same number again This will go 30 seconds until the system stops sounding b Alternatively disarm the alarm and then press the silent button The LED will flash a number of times and the system will beep the same number of times Every time you press the silent button the system will flash beep in accordance with the following table Number of Trigg
3. extended along a plastic component and taped into position Do not tape within the wiring harness and do not connect to ground earth The GREEN wire is the trigger wire for the optional Immobilisation relay Instructions for connection are included in the immobilisation kit If you are not using it tape the wire to the main harness in a tidy fashion The WHITE wire is an optional Trigger wire If you need to use this circuit the alarm will trigger if the switch you add to this circuit changes it s state ie open to closed or closed to open Connect the wire to a switch and the other side of the switch to a suitable ground When the switch changes the alarm will sound It can be connected to items such as a magnetic reed seat switch or pressure mat under the m c side stand or the Acumen garage kit See www acumen electronics co uk NOTE If a poor connection is made in this circuit the alarm will interpret any change of state regardless of how short in time as an alarm and will react accordingly Make sure all connections are sound waterproof and cannot short Operation The visual indications are based on the assumption that the Pink wire Indicators and the Black Red wires LED have been connected See page 3 The standard key fob has three buttons Lock Unlock and Silent To Arm the system Press the Lock button of the fob The alarm will beep twice and flash the indicators twice The system LED will start to flash after
4. larger version of the wiring diagram can be found on the back page The RED wire is the alarm positive feed DO NOT connect this directly to the INBOOY PANEL scooter battery but connect to the positive terminal of the starter solenoid Use the Red tagged ring terminal from the fit kit The BLACK wire is the alarm negative connection Connect this wire to a suitable earthing point on the scooter frame DO NOT connect to the battery negative terminal Do NOT connect it to a sub frame or fairing frame An ideal spot is the connection of the scooter battery poe negative lead amp frame Use the Blue s faw aw tagged ring terminal from the fit kit E The BROWN wire should be connected PURPLE SRODA j GREEN to a circuit which becomes live when the i ignition is switched on Ideally this should be connected between the OPTIONAL ACCESSORY OPTIONAL ACCESSORY ignition switch and the scooter fuse box ey PAGER If this is not practical a good place is the feed to the rear brake light switch Acumen recommends this connection is soldered Connect the 6 way connectors together Should you require further options on the CAT 3 system please see the Optional Wiring see page 3 and proceed to Operation IGNITION SWITCH FUSE BOX OPTIONAL ACCESSORY TRIGGER SWITCH To get full basic operation of the SCOOTER System Acumen recommends ssid that you also connect the PINK indicators and Black R
5. button again and the unit will beep three times Troubleshooting 1 The alarm will not react to the fob a Check the fob batteries type CR2016 b Place the fob as near as possible to the alarm system main unit If it will now disarm there are probably spurious radio signals in the vicinity Move the scooter to another area c Check the system fuse If the alarm has no power it cannot power the radio receiver Switch on the scooter ignition if it disarms now the alarm s power supply is at fault fuse or connections 2 False alarms Remember The alarm may think it is being stolen which is different to it being faulty a Enter Diagnostic mode and find out why the alarm is was reacting b Take appropriate action such as i Enter Convenience Mode if it s a windy day see page 4 ii Check earth power connections if you repeatedly get a power interrupted signal 3 The alarm fuse keeps failing The system cannot blow the fuse It is what the alarm switches that blows the fuse usually the indicators Make sure there are no shorts in the indicator system and if a new fit make sure the alarm PINK wire s is are not connected to the negative side of one or both of the m c indicators Spares and Accessories Acumen can supply a range of spares amp accessories to enhance the features of the SCOOTER system 1 Spare and replacement remote fobs and batteries 2 The key fob can be up
6. ecurity Precautions While the Acumen SCOOTER provides state of the art electronic security and protection it will not by itself ensure your scooter will not be stolen We recommend you undertake basic security precautions such as Parking in a locked garage if possible Parking in well lit areas if a garage is not applicable Using a bike cover where appropriate Using a chain or shackle and ground anchor Warranty terms and Conditions Full details are given in the Terms and Conditions document www acumen electronics co uk Wiring Diagram IGNITION LED 10A FUSE S DRILL 8MM DIA HOLE RED STARTER 12V BATTERY i INBODY PANEL INDICATORS i 2 WAY CONNECTOR E i PINK PINK RED BLACK FUSE BOX i BLUE BLUE min HUB EY z A A PURPLE REMOVE ADD GREEN GREENI re piace EROWN GU GUGU ANTENNA NUDGE FACILITY 7 i YELLOW i i eee EEA y SS i OPTIONALACCESSORY Optional ACCESSORY alls ONAE IMMOBILISATION RELAY PAGER TRIGGER SWITCH SWITCH
7. ed LED wires see page 3 Optional Wiring Acumen recommends that the following wires are connected to get full basic operation of the SCOOTER System however they are not critical to the operation of the system Flashing Indicators The two PINK wires are for the indicators Connect one Pink wire to the LH indicator and the other Pink wire to the RH indicators Ensure you connect these wires to the positive side of the indicators if you connect to the negative side of the indicators the alarm fuse will fail Acumen recommend these connections are soldered Flashing LED The paired Black Red wires with the two way connector are for the LED system indicator Connect the two plugs together Movement Sensing Nudge Facility The two BLUE wires one with a male connector on it one with a female connector are to remove add the nudge facility of the movement sensing e If the two blue wires are connected the nudge sensing is added e Dis connecting these two wires removes the nudge sensing Optional Wiring Connections not required for basic operation The YELLOW GREEN wire is the Pager wire It supplies 12v at 0 54 when the alarm is reacting It is designed to connect to the Acumen AlarmMate Pager Acumen Pt No 10114 and or the Acumen external siren Acumen Pt No 10115 IMPORTANT If this wire shorts to Ground while the alarm is sounding the alarm ECU will be damaged The PURPLE wire is the alarm antenna It should be
8. er Reason Flashes Beeps No Triggers in last armed period Power was interrupted The SCOOTER does not have an internal battery but if the power is disconnected when the unit is armed and then re connected it will give a reaction 3 Ignition turned on or hot wired movement SSCS i 5 Accessory switch was operated New Key Fob Lost Key Fobs If you can disarm the system ie you have a working fob and need to add another 1 Switch ignition off 2 Disarm the system from the fob 3 NOTE Sections 4 and 5 must be completed within 10 seconds 4 Switch the ignition on off 5 times in quick succession leaving the ignition ON at the 5th action 5 Change the state of the accessory switch circuit WHITE wire ie connect to ground if not connected and vice versa The unit will beep once and enter learn mode 6 Press and hold the Lock button until the unit beeps then release it 7 The unit will beep twice 8 Press and hold the Lock button again and the unit will beep three times If the system is dis armed but you don t have a working fob you have lost all working fobs 1 Switch off the scooter ignition 2 Remove alarm fuse 3 Leave for 5 minutes 4 Reconnect alarm fuse and within 10 seconds perform sections 5 amp 6 5 Switch the ignition on off 5 times in quick succession leaving the ignition ON at the 5th action 6 Change the state of the accessory switch circuit WHITE wire ie connect to gr
9. g positioning the SCOOTER main unit ECU Electronic Control unit When mounting the unit use the 5mm screws nuts supplied in the fitting kit or cable tie the unit to a suitable frame tube Take care to mount the unit where access to it is protected the more difficult it is to reach the harder the job the thief has to bypass the alarm Route the wiring alongside the scooter wiring and tape it in the style of the original scooter wiring Siting positioning the LED system Indicator Be aware the LED will result in a small increase of electrical current drain The LED draws 1mA of electrical current The LED provides a visual indication of the alarm s status helps with the diagnostic mode of the alarm and will warn a potential thief that your scooter is alarmed and that the alarm is armed For this reason it is preferable to position the LED where it can be easily seen Having decided on a suitable position drill an 8mm hole pass the LED through from the back of the hole and then insert the LED into the LED holder Then push the LED holder back into the 8mm hole to mount it securely Route the LED wires to the position of the SCOOTER ECU The alarm has a loom which ends in a 6 way connector This connector connects to the wiring loom which is connected to the scooter Installation and Wiring To make the alarm active you only need to connect the Red Black and Brown wires Connect the system wires as follows A
10. graded to the same flip fob as used on the Acumen Thatcham specification CAT1 and CAT21 systems The Flip fob uses Microchip KeeLog code hopping technology which prevents scanning and recording of transmitter codes When ordering specify Acumen part number 51020 and your make model and year of scooter NOTE The Acumen SCOOTER cannot know both types of fob at the same time If it knows the standard fob it cannot know a flip fob at the same time It can know 2 x standard fobs at the same time or 2 x flip fobs at the same time but not 1 of each 3 Different coloured System LED s to match your scooter Green Red White Blue Yellow 4 Acumax 900 Intelligent float battery charger 5 Extra external sirens If your SCOOTER system is buried in the scooter the audible warning may not be as loud as you would like This extra siren will allow you to position it where the sound can get out The SCOOTER can be further upgraded Upon request Acumen will supply you free of charge with a protecting clamshell to prevent easy disconnecting of the alarm system The clamshell will prevent easy unplugging of the 6 way connector Please request Acumen part number C 07 0003 The SCOOTER also has the ability to be connected to the following optional components 1 Starter immobilisation kit Acumen part number 10113 2 Acumen AlarmMate pager Acumen part number 10114 General S
11. ound if not connected and vice versa The unit will beep once and enter learn mode 7 Press and hold the Lock button until the unit beeps then release it 8 The unit will beep twice 9 Press and hold the Lock button again and the unit will beep three times NEW REPLACEMENT UPGRADED KEY FOBS CAN BE ORDERED DIRECT FROM ACUMEN wwiw acumen electronics co uk If the system is armed and you don t have a working fob you have lost all working fobs 1 Ensure the scooter ignition is switched off 2 Remove the alarm fuse 3 Leave for 5 minutes 4 Replace the alarm fuse the alarm will sound for 30 seconds unless the system has sounded 10 times for power loss in which case there will not be an audible reaction but wait 30 seconds Ensure the ignition is OFF during this time and ensure the alarm is not triggered by accessory switch or movement 5 Trigger the alarm by turning ON the ignition When the alarm sounds turn the ignition OFF When the siren stops after 30 seconds ie during the quiet time you have 10 seconds to perform steps 6 amp 7 6 Switch the ignition on and off 5 times leaving the ignition ON at the fifth action 7 Change the state of the accessory switch circuit WHITE wire ie connect to ground if not connected and vice versa The unit will beep once and enter learn mode 8 Press and hold the Lock button until the unit beeps then release it 9 The unit will beep twice 10 Press and hold the Lock
Download Pdf Manuals
Related Search