APC NetShelter AR4038A User's Manual
Contents
1. NetShelter CX Enclosure Avoid clustering hot running equipment such as servers dense redundant arrays of independent disks RAID and large voice over internet protocol VOIP switches in one part of the enclosure Distribute the thermal load evenly up and down the enclosure such that each fan module supports an equal amount of the thermal load lt 1 Fan module 2 ty e Fan modu Each fan module has a triangular metal section protruding slightly into the enclosure This does not create an issue for installation of most equipment but to allow for ample cabling space to the rear of the enclosure deep servers should be installed in the enclosure space above and below these triangular metal protrusions NetShelter CX Enclosure Installation and Customization Dimensions Enclosure dimensions internal Reduction in internal cabinet depth in some rack units due to triangular protrusion of fan modules Dimension key e a 775 mm 30 5 in s b 800 mm 31 5 in e c 860 mm 33 5 in e d 1010 mm 39 5 in e e Indicates soundproofed cable entry exit pathway Enclosure dimensions AR4018A AR4024A AR4038A AR40181IA AR40241A AR40381A Rear Front rack rack posts posts Rear Front rack rack posts posts 14 NetShelter CX Enclosure Installation and Customization Cable Management The NetShelter CX enclosure has a cable access opening cable port at the rear of the enclosure The 38U2. a depth of 800 mm 31 5 in The front mounting flanges are adjustable towards the rear of the enclosure to accommodate different rails or equipment with other depths The rear mounting flanges are adjustable towards the front The flanges can be adjusted to be as close as 120 mm 4 7 in or as far as 880 mm 34 6 in apart in 40 mm 1 5 in increments Note If the front accessory channel is removed from the enclosure the front rails can be adjusted forward 8 cm 3 14 in A common application for the enclosure is to move the flanges to a depth of 476 mm 18 75 in to accommodate networking and telecommunications equipment ns1551a Adjusting the vertical mounting flanges on the side braces Perform this procedure without any equipment installed on the mounting flanges 1 Use a Phillips screwdriver not provided to remove the screws in the vertical mounting flange ns1552a 2 Move the pre installed caged nut to the desired location then reposition the vertical mounting flange to this position and install the screws A fe ns1553a ea DB DO E OD DE e I SP NetShelter CX Enclosure Installation and Customization 11 Installing Equipment This section
3. management options for 600 mm and 750 mm enclosures Product SKU Description Figure 19 inch AR8602 1 U Route patch cables horizontal horizontally at the cable AR8600 2 U front or rear of a organizers 19 inch EIA AR8601 enclosure 2 U double sided AR8603A 2 U high density Cable AR8113A Fastens cables to management posts mounting rings rails or braces co 19 inch AR8425A Routes cables horizontal 1U horizontally on the cable front or back of the organizer AR8426A 19 inch EIA rack 2U 19 inch 2 U AR8427A Routes cables patch cord horizontally on the organizer front or back of the 19 inch EIA rack 19 inch 2 U AR8428 Routes cables horizontal horizontally or front cable to rear gt organizer SALI pass through 19 inch 1 U AR8429 Assists with cable pass containing air in the through with enclosure brush strip Cable AR7710 Contains cables containment along the vertical 0U a brackets accessory channel and is installed without tools Quantity of six NetShelter CX Enclosure Installation and Customization Product SKU Description Figure Zero U accessory mounting bracket AR7711 The bracket can be mounted in various locations throughout the enclosure for supporting small accessories and equipment Vertical Cable Organizer for NetShelter 0 U Channel AR8442 Eliminates cable stress by organizing cable layout within th
4. support information www apc com support Global support searching APC Knowledge Base and using e support e Contact the APC Customer Support Center by telephone or e mail Local country specific centers go to Www ape com support contact for contact information For information on how to obtain local customer support contact the APC representative or other distributors from whom you purchased your APC product 2012 APC by Schneider Electric APC the APC logo NetShelter and Kell Systems are owned by Schneider Electric Industries S A S American Power Conversion Corporation or their affiliated companies All other trademarks are property of their respective owners 990 3594A 001 08 2012
5. the instructions carefully and look at the equipment to become familiar with the device before trying to install operate service or maintain it The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided can result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided can result in minor or moderate injury NOTICE NOTICE addresses practices not related to physical injury including certain environmental hazards potential damage or loss of data NetShelter CX Enclosure Installation and Customization Disclaimer The information presented in this manual is not warranted by Schneider Electric to be authoritative error free or complete This pu
6. under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection inappropriate on site operation conditions corrosive atmosphere repair installation exposure to the elements Acts of God fire theft or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been altered defaced or removed or any other cause beyond the range of the intended use THERE ARE NO WARRANTIES EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE OF PRODUCTS SOLD SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH APC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE APC EXPRESS WARRANTIES WILL NOT BE ENLARGED DIMINISHED OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC S SOLE LIABILITY AND PURCHASER S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES APC WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES NetShelter CX Enclosure Installation and Customization 21 IN NO EVENT SHALL APC ITS OFFICERS DIRECTORS AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT SPECIAL CONSEQUENTIAL OR PUNITIVE DAM
7. AGES ARISING OUT OF THE USE SERVICE OR INSTALLATION OF THE PRODUCTS WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT IRRESPECTIVE OF FAULT NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES SPECIFICALLY APC IS NOT LIABLE FOR ANY COSTS SUCH AS LOST PROFITS OR REVENUE LOSS OF EQUIPMENT LOSS OF USE OF EQUIPMENT LOSS OF SOFTWARE LOSS OF DATA COSTS OF SUBSTITUENTS CLAIMS BY THIRD PARTIES OR OTHERWISE NO SALESMAN EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY WARRANTY TERMS MAY BE MODIFIED IF AT ALL ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL DEPARTMENT Warranty claims 22 Customers with warranty claims issues may access the APC customer support network through the Support page of the APC Web site www apc com support Select your country from the country selection pull down menu at the top of the Web page Select the Support tab to obtain contact information for customer support in your region NetShelter CX Enclosure Installation and Customization APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways e Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests www apc com Corporate Headquarters Connect to localized APC Web sites for specific countries each of which provides customer
8. Arc k by Schneider Electric oa oN Installation and i Customization NetShelter CX Enclosures Za aa si b SSS This manual is available in English on the APC Web site www apc com Dieses Handbuch ist in Deutsch auf der APC Webseite www apc com verf gbar Este manual esta disponible en espafiol en la pagina web de APC www apc com Ce manuel est disponible en fran ais sur le site internet d APC www apc com Questo manuale disponibile in italiano sul sito web di APC www apc com RV a VK EOBBICMHIET A I APC 7 TET b www ape com D gt 47 va Sa a os Instrukcja obs ugi w j zyku polskim jest dost pna na stronie internetowej APC www apc com Este manual esta dispon vel em portugu s no site da APC www apc com aHHoe PyKOBOACTBO Ha PyCCKOM A3bIKe AOCTYNHO Ha ca te APC www apc com Bu kullanim klavuzunun T rk esi APC web sayfasinda www apc com mevcuttur E APC SINN Up C www apc com BAFER Contents General Information sss sese esse cesses eee Important Safety Information se e e e e e x x x e ee 1 DISCIGINGE sciiaoetnneione acetals eee ee ee wee aa sites eee ens 2 About This Manual s e e e e eee eee 2 Related Documents sss ieee ree Chee aS a ies OAS 2 User Comments 9 5 6 025 occ toe a RRR RRR RRR A he oaks 2 Product Overview css sss sees sese seene Description sesi T C dra R a
9. R T a K R R RTA N KT Ra a TT R a 3 NetShelter CX Enclosures s e x x eee eee eee eee 3 Product Inventory lt lt Ze a aaa ere ree et eee eee lee eee Pees 4 Enclosure components e e e e e eee eens 4 Important lnformation sss sss ss esse ese sees se eee eee eee TOONS l Oe ee eS Ea 5 Other tools required not provided 2 2205 5 Safety Woohoo s Ste Seis iandae aS aie Et te hae a E edt ae Se ele ee er 5 Important Safety Instructions e x e K x eee eee 5 Moving the enclosure 200 2c eee e eee eee 5 Configuration cst anne ae teres Peete E EA eee 6 Blanking panels ce e x e e e cece eee 6 Front doors and Side Panels 0 000 e eee eee eee eee 6 Hinge Operation x e x x e e e eee eee 6 TAS CAM n OND TTT Installation and Setup e e c eee eee 8 Leveling the enclosure and installing bottom trim 8 Rack stabilization options e cee 8 NetShelter CX Enclosure Installation and Customization Removing and Installing Fan Modules 0022eeeeeee 9 Unlock the fan module 00 cece eee eens 9 Lock the fan module e x cee eee eee eee ees 9 Removing the fan module 0000 eee ee eee eee 9 Installing the fan module 00222 2s eee eee eee 9 Rack PDU ei akt Ree eee are We aeons ele Sales ea 10 AP9567 North American e e x K eee eee eee 10 AP9568 International e x cece ee e
10. blication is not meant to be a substitute for a detailed operational and site specific development plan Therefore Schneider Electric assumes no liability for damages violations of codes improper installation or any other problems that could arise based on the use of this publication The information contained in this publication is provided as is and has been prepared solely for the purpose of evaluating data center design and construction This publication has been compiled in good faith by Schneider Electric However no representation is made or warranty given either express or implied as to the completeness or accuracy of the information this publication contains IN NO EVENT SHALL SCHNEIDER ELECTRIC OR ANY AFFILIATE OR SUBSIDIARY COMPANY OF SCHNEIDER ELECTRIC OR THEIR RESPECTIVE OFFICERS DIRECTORS OR EMPLOYEES BE LIABLE FOR ANY DIRECT INDIRECT CONSEQUENTIAL PUNITIVE SPECIAL OR INCIDENTAL DAMAGES INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS CONTRACT REVENUE DATA INFORMATION OR BUSINESS INTERRUPTION RESULTING FROM ARISING OUT OF OR IN CONNECTION WITH THE USE OF OR INABILITY TO USE THIS PUBLICATION OR THE CONTENT EVEN IF SCHNEIDER ELECTRIC HAS BEEN EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SCHNEIDER ELECTRIC RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITH RESPECT TO OR IN THE CONTENT OF THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME WITHOUT NOTICE Copyright intellectual and all other prop
11. ck PDU power cord not shown are not installed and can be found inside the enclosure 4 NetShelter CX Enclosure Installation and Customization Important Information Tools Other tools required not provided CP Phillips screwdriver Utility knife Level Cage nut tool Safety Important Safety Instructions Save These Instructions This manual contains important instructions that must be followed during installation operation and maintenance of the equipment Use caution when moving an empty enclosure on its casters the enclosure may be unstable when pushed or pulled from the side Push the enclosure from the front or back when moving it on its casters For extra stability load 158 kg 350 lbs of equipment into the bottom of the enclosure before moving it on its casters A WARNING TIPPING HAZARD Stabilize the enclosure before installing the components Do not extend components on sliding rails out from the enclosure until you have installed three or more pieces of similar equipment or the stabilizer plate or bolt down brackets are installed e Do not extend more than one component from the enclosure at a time e Load the heaviest components first and place them toward the bottom of the enclosure to prevent the enclosure from becoming top heavy Failure to follow these instructions can result in death serious injury or equipment damage NOTICE To ensure adequate air movement place the side of th
12. e enclosure no closer than six to eight inches to the wall Moving the enclosure Casters The total load on the casters may not exceed 450 kg 992 Ibs See the enclosure Specifications on page 20 The front wheels have 360 degree rotation for maneuverability Rear wheels have front to back motion for stability Push the enclosure from the front or the back not the sides it may be unstable when pushed from the side For greater stability load 159 kg 350 lbs or more of equipment into the enclosure before moving it on its casters NetShelter CX Enclosure Installation and Customization Configuration Before installing the enclosure plan the location and space needed to install equipment and plan the ergonomics of keyboards and video monitors Improper airflow could damage installed components Blanking panels Use blanking panels to close up large open spaces in the CX but not to completely seal the rack The NetShelter CX works best when air can travel not just through the equipment vents but also above and below any equipment that generates thermal energy APC offers modular plastic Airflow Management Blanking Panels that snap into place without tools AR8136BLK Front doors and Side Panels The front doors and side panels may be opened or removed to access the interior Locking side panels offer additional security and assist with proper airflow within the enclosure The locking side panel does not
13. e rear channels of the enclosure Takes up zero U of space within the enclosure Consists of two pieces of equal size that when connected span the height of a 42 U enclosure Can be used in any APC enclosure Vertical fiber organizer and spools AR8443A The vertical fiber organizer and fiber organizer spools provide a method to manage fiber cabling within an enclosure and mount toollessly into the vertical OU accessory channel of the enclosure Quantity of two ns1156a ns1163a Fiber organizer spools only AR8444 Can be mounted toollessly to the vertical fiber organizer or attached with screws to the mounting rails of 750 mm wide enclosures NetShelter CX Enclosure Installation and Customization 18 Product SKU Description Figure 1 U cable ring Toolless Hook and Loop Cable Managers AR7707 AR8621 Fastens cables to posts for use with 750 mm enclosure networking applications hook and loop cable fastener for organizing data cable bundles Various mounting positions are available on the back panel of a vertical cable organizer Quantity of ten A toolless mount Fixed shelf 50 lb AR8105BLK Cantilever fixed shelf to enable the mounting of a monitor or other equipment into the rack environment or to allow cable pass through from the front to rear of the enclosure NetShel
14. ee 10 Specifications 0 isis ihe eich eee Bho eet ei ee Bee 10 EleCtriCal a aN dct ee eee Ge eae ENR oe ee ele eee 10 Vertical Mounting Flanges 0 000 x cee eee 11 Adjusting the vertical mounting flanges on the side braces 11 Installing Equipment 222 73 fii e x e x x e e e teed tte 12 Identifying one U space on the vertical mounting flange 12 Installing cage nuts e e e cee eee 12 Removing cage nuts e e nananana nannan 12 Equipment Planning Guidelines 000 eee eens 13 DIMGNSIONS ss ce eee lt ee aa eee ees ees 14 Enclosure dimensions internal 000e eee ee een eeee 14 Cable Management x cece eee eee eee eee eens 15 Rear cable access port 00 cece eee eee eee eee 15 Vertical OU accessory channels x e x e ees 15 Cable management options for 600 mm and 750 mm enclosures 16 Cooling 2365 2 XT E aR R TRR RN ee eee ee eet 19 Enclosure placement lt e e e e cece eee 19 Specifications cesse eee esec esec eee eee ZU 750 mm 18 24 38 U Enclosures eee 20 Two Year Factory Warranty sss esse ees e ees sees sees 21 Terms of warranty lt a saa 7 aeaa R TR R 0 TR ATR eee 21 Non transferable warranty sx e x x x e e 21 EXCIUSIONS lt X 9 0 eee a d YR dN ee VTR R SX NEN 21 Warranty claims ETT 22 ii NetShelter CX Enclosure Installation and Customization General Information Important Safety Information Read
15. enclosure has an additional cable port at the top for cabling from above Four vertical OU accessory channels are factory installed in the enclosures A variety of other cable management accessories are available Visit the website at www apc com and go to the NetShelter CX product page for a full list of compatible cable management accessories Rear cable access port The cable port is large enough to accommodate several hundred ethernet cables and has a removable top cover The design is such that pre terminated data distribution panels can be installed effortlessly with no need for de termination and re termination Unscrew and remove one of the two thumbscrews to swing open the port door Unscrew and remove the second thumbscrew to fully remove the cable port door Vertical OU accessory channels The vertical 0U accessory channels provide toolless mounting capabilities for APC Rack Power Distribution Units APC cable containment brackets and tie off locations for cables The standard position for the accessory channels is two located in the front of the enclosure and two in the rear of the enclosure Removing vertical OU accessory channels Vertical OU accessory channels can be removed completely from the enclosure Loosen the fasteners that attach the vertical OU accessory to the enclosure ns1600a NetShelter CX Enclosure Installation and Customization 15 Cable
16. evels of approximately 50 dB NetShelter CX Enclosure Installation and Customization AR4038A AR40381A 1950 mm 77 in 750 mm 30 in 1130 mm 44 5 in 199 4 kg 438 7 1b 232 24 kg 510 9 1b 60 96 mm 2 40 in 250 kg 550 Ib 3 6 kW 12 300 BTU hr 101 watts Up to 18 5 dB Two Year Factory Warranty This warranty applies only to the products you purchase for your use in accordance with this manual Terms of warranty APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase APC will repair or replace defective products covered by this warranty This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way Repair or replacement of a defective product or part thereof does not extend the original warranty period Any parts furnished under this warranty may be new or factory remanufactured Non transferable warranty This warranty extends only to the original purchaser who must have properly registered the product The product may be registered at the APC Web site www apc com Exclusions APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user s or any third person s misuse negligence improper installation or testing Further APC shall not be liable
17. ice environments The enclosures provide storage for industry standard EIA 310 19 inch rack mount hardware which includes servers voice data networking internetworking and APC power protection equipment NetShelter CX Enclosures Rack Mounting Rack Mounting External Model Availability Height Width Enclosure Width Enclosure Depth North AR4018A America 18 UT 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in AR4018IA International 18 U 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in North AR4024A America 24U 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in AR40241A International 24 U 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in North AR4038A America 38 U 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in AR4038IA International 38 U 482 mm 19 in 750 mm 29 in 1130 mm 44 5 in One U 44 45 mm 1 75 in See Identifying one U space on the vertical mounting flange on page 12 NetShelter CX Enclosure Installation and Customization Product Inventory Enclosure components Top cable access port Leveling foot Fan module Vertical mounting flange Side panel Front vertical OU accessory channel G Key Front door 6 Bottom trim Airflow opening Rear cable access port B Fan module power supply Caster Basic Rack PDU The bottom trim leveling feet door keys and ra
18. provides information on how to install rack mount equipment in the enclosure The instructions provided with the equipment provide more detailed information Identifying one U space on the vertical mounting flange When installing equipment locate the top and bottom of a U space on the mounting flanges Every third hole on the mounting flanges of a NetShelter enclosure is numbered to indicate the middle of a U space A U space consists of one of these numbered holes and one hole directly above and below it as shown 7 S ns0014a Installing cage nuts APC offers a cage nut hardware kit AR8100 for use with square holes Install cage nuts horizontally with the ears engaging the sides of the square hole Do NOT install cage nuts vertically with the ears engaging the top and bottom of the square hole 1 Insert the cage nut into the square hole by hooking one ear of the cage nut assembly through the far side of the hole Note Install the cage nuts on the interior of the vertical mounting flange 2 Place the cage nut tool not provided on the other side of the cage nut and pull to snap it into position P Removing cage nuts 1 Remove any attached screw 2 Grasp the cage nut and squeeze the sides to release it from the square hole 12 NetShelter CX Enclosure Installation and Customization Equipment Planning Guidelines Please note the following guidelines for proper installation and operation of hardware in a
19. rietary rights in the content including but not limited to software audio video text and photographs rests with Schneider Electric or its licensors All rights in the content not expressly granted herein are reserved No rights of any kind are licensed or assigned or shall otherwise pass to persons accessing this information This publication shall not be for resale in whole or in part Electrical equipment should be installed operated serviced and maintained only by qualified personnel A qualified person is one who has skills and knowledge related to the construction installation and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved About This Manual This manual is intended for users of the specified APC equipment It contains important safety warnings and instructions gives an introduction to the display interface and provides detailed information for proper use of the equipment Related Documents Download technical publications and other technical information or look for updates to your manual at our website at www apc com User Comments Contact www apc com support We welcome your comments about this document 2 NetShelter CX Enclosure Installation and Customization Product Overview Description NetShelter CX enclosures are specialized enclosures with integrated cooling noise dampening and power distribution for server and network applications in off
20. ship locked To avoid personal injury or damage to the enclosure one person should support the door or side panel while another person removes the door or side panel from its frame A CAUTION WEIGHT AND LEVERAGE HAZARD Doors and side panels are heavy Removal or installation requires two people Failure to follow these instructions can result in moderate personal injury Hinge Operation Installation Slide the hinge on the door or side panel into the front of the mounting plate attached to the inside of the enclosure G Using finger pressure press the hinge onto the _ mounting plate The latch will secure with an audible click a X i TT 6 NetShelter CX Enclosure Installation and Customization Three hinges are attached to their mountings in the enclosure to complete door installation 38 and 24U racks have three hinges per door The 18U racks have two hinges per door Removal press on the hidden latch under the side arm Lift the hinge arm off the mounting plate Slide the latch and door away from the mounting plate When all hinges are detached from their mountings the door can be removed NetShelter CX Enclosure Installation and Customization ns1533b ns1968a ns1532b Installation Installation and Setup If equipment mounting rails are adjusted from their standard factor
21. ter CX Enclosure Installation and Customization Cooling Enclosure placement When placing the NetShelter CX in an open office environment The rear of the unit can be pushed fully against a wall Six to eight inches of clearance should be left on either side of the unit e Do not place the enclosure unit in direct sunlight or in a small non airconditioned space e Place the enclosure close to ventilation or cool air ingress points in the room Air Paths FRONT REAR NetShelter CX Enclosure Installation and Customization 19 20 Specifications Item Height Width Depth Net weight cabinet Net weight packaged Clearance for wiring between front door and vertical rail Maximum equipment Weight static load Maximum recommended thermal load Power consumption Noise reduction AR4018A AR40181A 1050 mm 41 in 750 mm 30 in 1130 mm 44 5 in 134 2 kg 295 2 Ib 163 72 kg 360 2 Ib 60 96 mm 2 40 in 310 kg 680 Ib 1 2kW 4 100 BTU hr 39 watts Up to 18 5 dB 750 mm 18 24 38 U Enclosures Measurements AR4024A AR40241A 1290 mm 51 in 750 mm 30 in 1130 mm 44 5 in 163 4 kg 359 5 1b 193 7 kg 426 1 1b 60 96 mm 2 40 in 280 kg 615 1b 2 4 kW 8 200 BTU hr 68 watts Up to 18 5 dB 718 5 dB equates to perceived drop in noise of 98 5 The NetShelter CX generates 48 5 dB of noise during normal operation This is below standard office ambient noise l
22. the top when removing the fan modules 1 Detach the clip 2 Swing the fan module out on its hinges 3 Disconnect the fan module power supply plug from the fan module ns1973a 4 Lift the fan module from the hinges attached to the enclosure Installing the fan module ns1972a Reverse the procedure to install the fan module NetShelter CX Enclosure Installation and Customization Rack PDU The NetShelter CX Enclosure is provided with one Basic Rack PDU The Rack PDU distributes power to devices in the enclosure AP9567 North American Outlets The Rack PDU has fourteen 14 NEMA 5015R outlets Power cord The 12 foot 3 66 meter power cord terminates with a NEMA 5 15P plug AP95668 International Outlets The Rack PDU has fifteen 15 IEC 320 C13 outlets Power cord The 6 5 foot 1 98 meter power cord terminates with a IEC 320 C14 plug Specifications Electrical Input connector Output connectors AP9567 AP9568 NEMA 5 15P IEC 320 C14 inlet 14 NEMA 5 15R outlets 15 IEC 320 C13 outlets Nominal input voltage 100 120 VAC 120 240 VAC Acceptable input voltage 10 of nominal voltage Input frequency 50 60 Hz 10 NetShelter CX Enclosure Installation and Customization Vertical Mounting Flanges Vertical mounting flanges come factory installed on the enclosure in the proper position for use with rack mountable equipment having
23. y installed positions to a deeper position such as in a networking application the levelling feet must be used Note The bottom trim and leveling feet are packaged separately and placed in the enclosure Leveling the enclosure and installing bottom trim Level the enclosure before installing equipment The leveling feet at the corners provide a stable base if the floor is uneven but they cannot compensate for a badly sloped surface 1 Move the enclosure to a level location 2 For each leveling foot turn the leveling foot clockwise to extend the leveling foot until it makes firm contact with the floor ae T cC 3 Install the front and side bottom trim Z B The enclosure can be leveled after equipment has been installed Turn the leveling foot clockwise to extend the S leveling foot until it makes firm contact with the floor o D oO D E o Rack stabilization options Lock the casters for additional stabilization ns1590a 8 NetShelter CX Enclosure Installation and Customization Removing and Installing Fan Modules Unlock the fan module Open the right hand side panel Unscrew the thumbscrew on the right side of the fan module to unlock the fan module so it can be opened Lock the fan module Open the right hand side panel Install the thumbscrew on the right side of the fan module to lock the fan module in place ns1457c Removing the fan module Start at
Download Pdf Manuals
Related Search