AOC FT710 User's Manual
Contents
1. Missing one of the primary colors RED GREEN or BLUE Inspect the monitor s video cable and make sure that none of the pins are bent INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor do the following e Carefully turn the monitor on its side or upside down see figure 1 e Locate the cavities at the bottom front of the monitor e Insert the pegs on the swivel base into these cavities Push the swivel base forward until the swivel base locks in place e To remove the swivel base hold the bottom of the swivel base then push it out POWER CORD Power Source 1 Make sure the power cord is the correct type that required in your area 2 This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required 3 Connect the power cord into your monitor s power input socket and then plug the other end into a 3 pin AC power outlet The power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your monitor VIDEO CABLE Connecting the Video Cable the monitor comes with a built in video cable Plug the signal cable s 15 pin connector into the computer s video port and tighten the two screws on the cable connector see figure 2 Caution Don t bend the signal cable otherwise it will break the inner wire Connecting the Power2. 100 240V 50Hz 60Hz Operating 0 C to 40 C ambient Humidity 10 to 85 relative non condensing Dimension Monitor amp Base 410 W x 402 H 420 D mm Weight 17 0 kg Net Signal Cable Attached Mini D sub 15 Male Plug amp Play DDC1 2B Power On gt 75W Consumption Off lt 5W ode Power consumption Preset display area 75 Watts Max 310mm 230mm Regulations UL CSA FCC FDA TUV GS MPR II Preset Timing Table STANDARD RESOLUTION HORIZONTAL VERTICAL FREQUENCY FREQUENCY IBM 720 x 400 31 5kHz 70Hz VESA 85 640 x 480 43 3kHz 85 Hz Connector Pin Assignment HS Ju NO de fi aa Terminal NO Video C Green p Video Blue BLANK BLANK SDA serial data SENSES 13 GND R 14 address DDC clock For DDC
3. Cord Plug the power cord into the monitor s AC power socket Then plug the power cord into a grounded AC outlet or UL approved power strip or the power output socket on your PC Caution If the AC outlet is not grounded install the proper grounding adapter not supplied OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor See Figure 3 By changing these settings the picture can be adjusted to your personal preferences e The power cord should be connected e Connect the video cable from the monitor to the video card e To turn the monitor on press the power switch to ON position The power indicator will light up e Your monitor features a unique quick switch system which provides a picture within seconds after the monitor is switched on NOTES e Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock e Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor e For maximum protection repackage your monitor as it was originally packed at the factory e To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive c
4. FT710 17 Flat CRT TOO User s Manual By Envision Peripherals Inc www aocmonitor com AOC EYES VALUE Thank you very much for choosing the AOC Color Monitor We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor Please keep this manual in a safe place for your future reference Plug amp Play Drivers for the AOC Series Monitors are available at www aocmonitor com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items 1 Monitor 2 Owner s Manual 3 Power Cord 4 Swivel Base FCC Class B Radio Frequency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to
5. arts causing a fire or electric shock Never spill liquids on the monitor O Do not attempt to service the monitor yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel O To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 1 5A O The wall socket shall be installed near the equipment and shall be easily accessible Attention Disconnect the power cord to stop the power supply to the monitor Plug amp Play DDC1 2B Feature This monitor is equipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the PC protocol The host can request EDID information over the DDC2B channel USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wall plug with NEMA 5 15 style and is UL listed and CSA labeled The voltage rating for the power cord shall be 125 volts AC Supplied with units intended
6. for connection to power outlet of personal computer Please use a cord set consisting of a minimum No 18 AWG type SJT or SVT three conductors flexible cord One end terminates with a grounding type attachment plug rated 10A 250V CEE 22 male configuration The other end terminates with a molded on type connector body rated 10A 250V having standard CEE 22 female configuration TECHNICAL SUPPORT FAQ Power LED is not on Power Cord should be connected No Plug Play Check if the PC System is Plug amp Play compatible Check if the Video Card is Plug amp Play compatible Check if the D 15 plug pin of Video Cable is bent Make sure the AOC Monitor Drivers are installed AOC Monitor Drivers are available at www aocmonitor com Picture is fuzzy Adjust the Contrast and Brightness Controls Picture bounces or a wave pattern is present in the picture Move electrical devices that may cause electrical interference The power LED is ON orange but there s no video or no picture Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitor s video cable is properly connected to the computer Inspect monitor s video cable and make sure none of the pins are bent Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key
7. leaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it Figure 1 Installing and Removing the Swivel Base 1 Signal Cable 2 Power Cord 3 VGA Card Connector D Figure 3 External Controls 1 Power ON OFF Switch 2 Power Indicator s 3 Menu 4 Contrast Right lt 0 g 5 Brightness Left CS 6 Exti A A AP 600 EY 1 1024 8 FRONT PANEL CONTROL see figure 3 Power ON OFF Switch Press this key to switch the display ON or OFF Power Indicator Green Power On mode Orange Off mode MENU Press this key to either bring up the OSD menu or select an item on the menu Contrast With the OSD menu on press this key to either select a function or to adjust up the value of a selected function With the OSD menu off press this key to adjust the contrast Brightness With the OSD menu press this key to either select a function or adjust down the value of a selected function With the OSD menu off press this key to adjust the brightness EXIT Exit a certain function or exit OSD setup ADJUSTING THE PICTURE see figure 4 l O CONTRAST Adjust the picture contrast BRIGHTNESS Adjust the picture brightness g CO H CENTER Adjust the horizontal position of the picture Adjust the picture s horizontal size Adjust the picture s vertical size Adj
8. n a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions O Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided O The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company O The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug O Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges O Do not overload power strips and extension cords Overloading can result in fire or electric shock O Never push any object into the slot on the monitor cabinet It could short circuit p
9. try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only PRECAUTIONS O Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement O Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor o
10. ust the picture s horizontal and vertical size simultaneously Y PINCUSHION Adjust the pincushion and barrel 9 TRAPEZOID Adjust the picture s trapezoid distortion 10 PIN BALANCE to compensate the pincushion PARALLELO Adjust the picture to be a rectangle R M AS ROTATION ROTATION Adjust the picture tilt to horizontal position 6500 K 9300 K The color temperature for 6500 K is x 0 313 COLOR y 0 329 and 9300 K is x 0 283 y 0 297 It TEMPERATURE presents two different color sets on the screen 14 4 USER COLOR If the 9300 K normal white or 6500 K warmer Red Blue white do not satisfy your desire properly adjust ie DEGAUSS If al cd occurs when moving or M e Knob Moire is he eel of Between the 16 MOIRE REDUCE phosphor layout and the video signal In some me RECALL Press RECALL to restore the monitor to factory settings EXIT Close OSD window Select the language as you like SPECIFICATION CRT Viewable Image Size 43 2cm 17 90 deflection 29mm neck 21mm H 0 25mm D dot pitch 40 6cm 16 diagonal Video 0 7Vpp R G B Analog Separate Sync TTL Level H V sync Positive Negative Scanning Frequency Horizontal 30kHz to 72kHz automatically Vertical 50Hz to 160Hz automatically Max Resolution 1280 x 1024 Video Dot Rate 110MHz Factory Preset 6 imings User mode Timings 8 Power Source Universal AC
Download Pdf Manuals
Related Search