American Standard Reliant 3 Bath and Shower Trim Kits User's Manual
Contents
1. at O A ADJUSTMENT WHEN WATER IS TOO HOT TEMPERATURE SUING NUMBERS PRY RED RING FORWARD AND ROTATE Pe s COUNTER CLOCKWISE ONE CLICK ADJUSTMENT WHEN WATER IS TOO COLD PRY RED RING FORWARD AND ROTATE CLOCKWISE t B m f faucet drips operate handle several times from off to on Do not apply excessive force m Clogged CARTRIDGE 4 inlets may cause reduced flow in full on hot or cold To clean inlets first turn off water supply then mw Remove HANDLE 1 CAP 2 and CARTRIDGE 4 Clean inlets and MANIFOLD 5 E Reassemble CARTRIDGE 4 alternately tightening SCREWS 3 E Replace CAP 2 and HANDLE 1 Check flow M9688982. American Standard Installation Instructions Reliant 3 T385 5XX BATH AND SHOWER TRIM KITS with EverClean Finish Congratulations on purchasing your American Standard faucet with the EverClean finish a feature found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots Eliminates the need for cleaners and enn Permanent surface protectant remains beautiful for the life of the faucet z Certified to comply with ANSI A112 18 1 To ensure that your installation proceeds smoothly please read these BS instructions carefully before you begin M968898 Required Tools gt gt EN 3 D A Phillips Screwdriver Flat Blade Screwdriver 5Sa Plumbers Putty or Caulking Granne FOEKE Teflon Tape ROUGHING IN DIMENSIONS E To assure proper positioning in relation to wall note roughing in dimensions INLETS el 3 4 TO 2 3 8 SHR 1 2 NOM 41416 COPPER SWEA FINISHED WALL SWEAT 1 2 NPT INLETS TUB 1 2 NOM i COPPER SWEAT gt gt OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65 AND 80 SWEAT lt 5 7 8 INLETS me SHR 1 2 NOM COPPER SWEAT SEE ILLUSTRATION f D TUB 1 2 NOM gt 74 FOR HEAD COPPER SWEAT INLETS CLEARANCE al 1 2 NOM COPPER SWEAT i OUTLETS INLETS 1 2 NPT 18 OPTIONAL 1 2 NPT 3 3 8 1 1 2 REF 3 3 8 j e INLETS 1 2 NPT 1 2 COPPER OUTLETS 5 1 2 REF 4 1 2 NPT TOP OF TUB RIM BOTTOM OF TUB THREADED I
3. NLETS THREADED INLETS STOPS EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface INSTALL TRIM When finished tiling the wall remove PLASTER GUARD 3 Push on CAP 1 Mount ESCUTCHEON 2 and with SCREWS 7 Install HANDLE 8 by pushing it onto CARTRIDGE STEM 9 and tightening SET SCREW 10 from below with 2 5mm Hex Wrench supplied Insert INDEX BUTTON 11 Remove cap from tub supply and plug from shower pipe Install SHOWER ARM 4 and FLANGE 13 Tighten SET SCREW 12 onto FLANGE 13 using 5 64 hex wrench Install SHOWER HEAD 5 onto SHOWER ARM 4 Install DIVERTER SPOUT 6 2 ADJUST HOT LIMIT STOP HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP E Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP 1 Follow Step A or B to adjust min max discharge temperature O being the hottest to 7 the coldest temperature setting Factory set
Download Pdf Manuals
Related Search