American Standard Hampton T980.702 User's Manual
Contents
1. 64 Drill a 3 16 hole in the finished deck See TEMPLATE for location SPOUT SHANK TEMPLATE FOR SPOUT ROLL PIN LOCATION 3 16 DRILLED HOLE QO Lubricate the SPOUT ADAPTER O RING 6 and SPOUT O RING 7 Push SPOUT ADAPTER 8 on SPOUT SHANK 9 and align slot in SPOUT ADAPTER 8 with 3 16 drilled hole Tighten SPOUT ADAPTER SET SCREW 10 securely with 4mm HEX KEY 11 Remove the PLUG BUTTON 12 from the SPOUT 13 Position the RUBBER RING 14 in the groove in the base of the SPOUT 13 Push the SPOUT 13 down onto the SPOUT ADAPTER 8 and tighten the GROOVE SET SCREW 15 securely with the 5mm HEX KEY 16 O RING Insert the PLUG BUTTON 12 into the SPOUT 13 2 VALVE TRIM m Place the ESCUTCHEON SEALS 1 over the VALVE BODIES 2 E Thread the VALVE ESCUTCHEONS 3 into the VALVE BODIES 2 Align the HANDLE STEM 4 with the SLEEVE 5 as necessary Thread the VALVE ESCUTCHEON 8 into the BODIES 2 until the ESCUTCHEON 3 contacts the finished deck 3 INSTALL HANDLES LEVER HANDLE Turn VALVE into OFF position Push ADAPTER 1 into HANDLE 2 in a way that the male square on the ADAPTER 1 fits in the female square of the HANDLE 2 Push HANDLE 2 and ADAPTER 1 onto VALVE STEM 4 Check alignment if not satisfactory aligned SS m Push out ADAPTER 1 carefully m Turn ADAPTER 1 either 45 or 90 so that male square on ADAPTER 1 catches different fema2. Installation HAMP Instructions DECK MPTON FILLER TRIM KIT T980 702 with EverClean Finish Lu ae 5 i s Congratulations on purchasing your American Standard faucet with EverClean finish found only on American T980 732 Standard faucets EverClean Finish e One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Certified to comply with ANSI A112 18 1 e Permanent surface protectant remains beautiful U S Patent No D403 750 for the life of the faucet e EverClean available on Polished Chrome Satin Nickel M968655 Rev 1 1 Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required tools 3 Phillips Screwdriver Screwdriver REMOVE ALL os i Channel Locks Hacksaw FINISHED a 1 1 1 2 SPOUT INSTALLATION Complete FINISHED DECK before trim installation Turn off the water supplies Remove the GUARDS 1 from the VALVES 2 Remove the GUARD 3 and 1 4 PLUG 4 from the SPOUT SHANK 5 21 64 The SPOUT SHANK 5 height should be 1 to 1 1 2 above the FINISHED DECK Cut the SPOUT SHANK 5 if necessary Remove all burrs and bevel the end of the shank Failure to do so may 3 16 DIA HOLE damage the SPOUT O ring during installation and cause water 19 8mm leakage 23 32 18 6mm DIA 47
3. le square in HANDLE BASE 2 Assemble and tighten HANDLE E SCREW 3 Push INDEX CAP 5 in top of HANDLE 2 TESTING Turn the HOT HANDLE 1 clockwise and the COLD HANDLE 2 counterclockwise to the off position Unscrew and remove the SPOUT END 3 Slowly turn on the water supplies Operate the HANDLES 1 2 to flush water E lines thoroughly Check SPOUT 4 connection for leakage Turn the Handles off Replace the SPOUT END 3 EverClean Finish Care Instructions CROSS HANDLE m Turn VALVE into OFF position Push ADAPTER 1 into HANDLE BASE 2 Push HANDLE BASE 2 ee and ADAPTER 1 onto a VALVE STEM 3 2 amp J Push CROSS 4 onto ADAPTER 1 Assemble and tighten HANDLE SCREW 5 Push INDEX CAP 6 in top of HANDLE 4 SERVICE To change the direction of handle rotation Turn off the water supplies Turn HANDLE 1 to the off position Remove the INDEX CAP 2 and the HANDLE SCREW 3 Pull the HANDLE BASE 4 off and remove ADAPTER 5 m Unscrew the VALVE ESCUTCHEON 6 Unscrew the VALVE LOCK NUT 7 and remove A 17mm deep socket is required Remove the CARTRIDGE 8 by pulling up on the SLEEVE 9 Remove the SCREW 10 from the CARTRIDGE 8 E Remove the SPRING CLIP 11 E Remove the STOP WASHER 12 Turn it 90 and replace m Replace the SPRING CLIP 11 m Reverse the above steps to reassembly the components If the spout drips o
4. perate the handles several times from the off to the on position Do not force the handles only turn 90 American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968655 Rev 1 1
Download Pdf Manuals
Related Search