American Standard Ellisse 2711.XXXW User's Manual
Contents
1. 752296 100 REV H 2 ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes WARNING When using electrical products basic precautions should always be observed including the following 1 DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter 2 Grounding is required The unit should be installed by a licensed electrician and grounded 3 Install to permit access for servicing 4 All building materials and wiring should be routed away from the pump body and heater if equipped 2 1 HORSEPOWER MODELS The whirlpool should be installed on a 120 vac 20 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit fron the electrical supply panel A grounded neutral wire and a third wire earth ground are essential ADDING THE SAFE T HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT ELECTRICAL INSTALLATION SEPARATE 20 AMP GFCI OUTLET FOR 2 1 HP MODELS WHIRLPOOL MOUNTED 120 VAC AIR OR ELESTROMIC SWITCH R WALL TIMER 2 1 HP AIRSWITCH MODELS ONLY ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 752296 100 REV H 3 WIRE SELECTION GUIDE Maximum distance from fusebox to motor The sizes shown on this chart are recommendations rerionmance only Always follow Rati2. H 4 SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER amp GAMBLE
3. ELLISSE 6 X 48 HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS 2711 XXXW SERIES WHIRLPOOL INSTALLATION INSTRUCTIONS Americam Standard 1829mm 72 ON OFF SWITCH ja 927mm gt 36 1 2 OUTLINE OF CUTOUT 1791 X 1181 70 1 2 X 46 1 2 4 ba 6s oa 305mm 4 12 C L OF DRAIN 229mm x 356mm 9 x 14 FLOOR CUTOUT 1219mm PUMP Yo bui ee ee E RECOMMENDED GRAB BAR a PROVIDE ACCESS OPTIONAL TO PUMP FOR SERVICE FITTING FITTING AREA LOCATION DECK FITTING ON ALL INSTALLATIONS 64X279mm AREA 2 1 2 X 11 SAFE T W LEVELING STRINGER HEATER NOT FOR SUPPORT 51mm REMOVABLE CIL OF 2 4 OVERFLOW 546mm 105mm INTEGRAL 21 1 2 FEET 4 1 8 SUPPORT ROUGH 495mm FLOOR ee LED 1 1 2 N P T M THREADS y 1 1 2 O D TAILPIECE L 121mm pamm 4 3 4 GENERAL SPECIFICATIONS FOR 2711 WHIRLPOOL INSTALLED SIZE 72 x 48 x 21 1 2 In 1829 x 1219 x 546mm WEIGHT 148 Lbs 67 Kg WEIGHT w WATER 965 Lbs 434 Kg GAL TO OVERFLOW 95 Gal 360 L WHIRLPOOL MIN OPERATING VOL 74 Gal 280 L BATHING WELL AT SUMP 43 x 28 In 1092 x 711mm BATHING WELL AT RIM 68 x 38 In 1727 x 965mm WATER DEPTH TO OVERFLOW 14 5 8 In 371mm FLOOR LOADING 40 Lbs Sq Ft 195 Kgs Sq m PROJECTED AREA 30 3 60 8 WHIRLPOOL ELECTRICAL SPECIFICATIONS SYSTEM PUMP 2 1 HP 14 4 AMPS 120V SYSTEM II P
4. UMP 2 1 HP 15 6 AMPS 120V GENERAL INSTALLATION INFORMATION 102mm THANK YOU for selecting an American Standard bath Your new bath is shipped to you after careful inspection The whirlpool version is completely assembled with pump motor and system piping All you need to finish the installation are your selected fittings and electrical connections for a whirlpool To insure maximum performance and pleasure from this product please follow the instructions and cautions List of Optional Components not included e Safe T Heater 9075 120 e Tile Bead Kit 751 755 100 List of Required Components not included e Drain 1583 470 e Bath Filler see your American Standard Distributor List of Required Tools and Supplies Tools Supplies e Level e Nails e Tape Measure e Putty e Pipe Wrench e Caulking waterproof e Slip Joint Pliers e 1x3or 2x2 e Screw Driver Stringers e Standard e Drop Cloth Woodworking Tools e 20 amp e Personal Safety GFI Outlet Equipment e Cement Plaster e Caulking Gun Grout Carefully uncrate and inspect your new bath for any shipping damage If such damage is found report it to your vendor immediately After inspection and during installation protect the bath from construction damage After installation and before enclosing with wallboard tile etc water test the unit and check for leaks Do not make modifications to the whirlpool system or remove pump fro
5. ary Mark the final position of the underside of the deck by tracing a line on to the studs see Figure 1 2 Remove the whirlpool and attach a 2 x 4 stringer to the studs with the top of the stringer touching the traced line 3 Install drain components to the whirlpool following the manufacturers instructions Before replacing your whirlpool for final installation be certain that an opening has been provided in the sub floor for the drain See the roughing in drawing for suggested opening size and location dimensions 4 Replace whirlpool and re shim the integral support feet shimming the entire length of the support feet Secure the shims using construction adhesive silicone mortar or equivalent materials While not a necessity the use of a foundation base consisting of cement e g Sakrete mortar or grout will help provide a solid and secure installation FIG 1 495mm 19 1 2 TYPICAL PIER TYPE INSTALLATION AS DESIRED 1791mm 495mm 19 1 2 72 1 8 LEVELING STRINGERS TILE A a LEVELING te Le TILE BEAD L 24 SURFACE STRIP WATERPROOF PR SEALANT BATH ADHESIVE UNLESS AN ACCESS OPENING OF BATH DESIRED ACCESS PANEL AT LEAST 12 X 24 305 X 610MM UNLESS AN ACCESS OPENING OF N IS PROVIDED WARRANTY SERVICE AT LEAST 12 X 24 305 X 610MM LEVELING WILL NOT BE PERFORMED IS PROVIDED WARRANTY SERVICE STRINGER WILL NOT BE PERFORMED
6. m factory mounting This could adversely affect the safety and performance of the whirlpool and void the warranty Do not handle or move the whirlpool by the pump motor or piping system Fittings bath filler shower arm etc are not provided with the bath and must be ordered separately Framing and enclosing materials are provided by others Check for availability of optional American Standard wall tiling bead required for recess installations Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth WARNING Do not lift whirlpool by the piping harness at any time FOR AFTER SALES SERVICE CALL 1 800 442 1902 WEEKDAYS 752296 100 REV H American Standard Inc 2003 All product names listed herein are trademarks of American Standard Inc unless otherwise noted INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown Locate studs as required Ensure roughing in dimensions are proper plumb and square Provisions must be made in all installations for an access opening for servicing the pump and controls It is strongly recommended that an additional opening be provided for access to the drain components NOTE The apron should not be used as the primary access opening 1 Position the whirlpool into the installation opening and level the deck shimming the integral support feet as necess
7. ng 120V Power Line local and national 2 1 I E R AAEEen DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening connect whirlpool drain to waste line Tighten all drain joints securely Check the pump couplings and make sure they are hand tight Clean the whirlpool and fill with water to a point 2 above the top of the highest jet Recheck the pump couplings and make certain that they are not leaking Although the pump couplings are factory tightened and inspected some loosening may have occured during transit Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on Check for leaks around all piping connections while the whirlpool is running POST INSTALLATION CLEAN UP Remove all construction debris from bath Tile grout can be removed with a wooden popsicle stick or tongue depressor Do not use wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be used since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax 752296 100 REV
Download Pdf Manuals
Related Search