American Standard 2770.XXXW User's Manual
Contents
1. SELECTION GUIDE Maximum distance from fusebox to motor The sizes shown on this chart are recommendations for copper conductors Motor High 7 only Always follow Performance 115V Power Line local and national 41 1 electrical codes DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening connect whirlpool drain to waste line Tighten all drain joints securely Check the pump couplings and make sure they are hand tight Clean the whirlpool and fill with water to a point 2 above the top of the highest jet Recheck the pump couplings and make certain that they are not leaking Although the pump couplings are factory tightened and inspected some loosening may have occured during transit Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on Check for leaks around all piping connections while the whirlpool is running POST INSTALLATION CLEAN UP Remove all construction debris from bath Tile grout can be removed with a wooden popsicle stick or tongue depressor Do not use wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be us2. access opening 1 Position the whirlpool into the installation opening and level the deck shimming the integral support feet as necessary Mark the final position of the underside of the deck by tracing a line on to the studs see Figure 1 2 Remove the whirlpool and attach a 2 x 4 stringer to the studs with the top of the stringer touching the traced line 3 Install drain components to the whirlpool following the manufacturers instructions Before replacing your whirlpool for final installation be certain that an opening has been provided in the sub floor for the drain See the roughing in drawing for suggested opening size and location dimensions 4 Replace whirlpool and re shim the integral support feet shimming the entire length of the support feet Secure the shims using construction adhesive silicone mortar or equivalent materials While not a necessity the use of a foundation base consisting of cement e g Sakrete mortar or grout will help provide a solid and secure installation FIG 1 464mm 18 1 4 464mm 18 1 4 8B an gor Da ac ol B ye lt LEVELING STRINGERS L WHIRLPOOL ONLY UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED TILE WALLBOARD TILE SEALANT BEAD STRIP BATH ADHESIVE LEVELING STRINGER NOTE Tile bead kit not included an
3. 59mm x 699mm WATER DEPTH TO OVERFLOW _ 114 In 356mm FLOOR LOADING ___ 41 Lbs Sq Ft 197 Kgs Sq m PROJECTED AREA PTS 15 6 pela i CUBE FT 29 6 for availability of optional American Standard wall tiling WHIRLPOOL ELECTRICAL SPECIFICATIONS bead required for recess installations Fittings bath filler shower arm etc are not provided with the bath and must be ordered separately Framing and enclosing materials are provided by others Check SYSTEM PUMP 1 1 HP 9 9 AMPS 120V Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth NOTE Deck mounted fittings are not recommended WARNING Do not lift whirlpool by the piping har FOR AFTER SALES SERVICE CALL 1 800 442 1902 WEEKDAYS Ness at any time American Standard Inc 2003 752481 100 Rev H All product names listed herein are trademarks of American Standard Inc unless otherwise noted INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown Locate studs as required Ensure roughing in dimensions are proper plumb and square Provisions must be made in all installations for an access opening for servicing the pump and controls access to the drain components It is strongly recommended that an additional opening be provided for NOTE The apron should not be used as the primary
4. CADET 5 x 32 2770 XXXW SERIES rta Standard HIGH GLOSS ACRYLIC WHIRLPOOL BATHING POOL SHOWN LESS ALL FITTINGS INSTALLATION INSTRUCTIONS PROVIDE ACCESS TO PUMP FOR THA NK YOU ae SERVICING ON ALL INSTALLATIONS ag 1521 mM for selecting an American Standard bath Your new 305 mm 59 7 8 bath is shipped to you after careful inspection The 222 mm 12 OUTLINE OF CUTOUT whirlpool version is completely assembled with pump 634 ae 1483 mm x 768 mm motor and system piping All you need to finish the gia S898 A GEUA installation are your selected fittings and electrical FINISHED 7 connections for a whirlpool e FittinG WALL Q i i PECS FOR To insure maximum performance and pleasure from MENSIONS ies this product please follow the instructions and iz N OFF i pa switcy Cautions List of Optional Components not included e Tile Bead Kit 751755 100 806 mm Bg enS e Apron Kit alee ae ae see your American Standard Distributor 15 7 8 k List of Required Components not included 1 ae za ey ARNANES e Drain 1583 470 e Bath Filler SUPPLIES 2 3 8 8 JETS see your American Standard Distributor Ne PERERA y SHOWER ARM List of Required Tools and Supplies OPTIONAITO Tools Sunpies INISHED FLOOR e Level Nails ae Pan e Tape Measure e Put
5. d must be purchased separately TYPICAL PIER TYPE INSTALLATION AS DESIRED 1483mm 58 3 8 CUTOUT AS DESIRED LEVELING SURFACE WATERPROOF SEALANT ACCESS PANEL WHIRLPOOL ONLY UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED 752481 100 Rev H ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes WARNING When using electrical products basic precautions should always be observed including the following 1 DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter 2 Grounding is required The unit should be installed by a licensed electrician and grounded 3 Install to permit access for servicing 4 All building materials and wiring should be routed away from the pump body and heater if equipped The whirlpool should be installed on a 120 vac 15 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit from the electrical supply panel A grounded neutral wire and a third wire earth ground are essential ELECTRICAL INSTALLATION SEPERATE 15 AMP GFCI OUTLET WHIRLPOOL MOUNTED 120 VAC AIR SWITCH OR WALL TIMER ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 752481 100 Rev H 3 WIRE
6. ed since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax 752481 100 Rev H 4 SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER amp GAMBLE
7. ty 65 amp 78 SS e Pipe Wrench e Caulking waterproof OVERFLOW 305 mm C L OF e Slip Joint Pliers e 1x3o0r2xe2 ae 12 ___ _ SPOUT E LEVELING e Screw Driver Stringers 70mm 102 mm eee e Standard e Drop Cloth 2 3 4 1 4 SUPPORT Woodworking Tools e 15 amp GFI e Personal Safety Outlet ah ie E on Equipment e Cement Plaster 19 3 4 N ee e Caulking Gun Grout a 18 1 4 GENERAL INSTALLATION INFORMATION Araian READE onm i Carefully uncrate and inspect your new bath for any BEET 4 OD TALPIEOE Z 23 m shipping damage If such damage is found report it to 4 5 8 your vendor immediately After inspection and during installation protect the bath from construction damage After installation and before enclosing with wallboard tile etc water test the unit and check for leaks GENERAL SPECIFICATIONS FOR 2770 WHIRLPOOL INSTALLED SIZE _____ 59 7 8 x 31 3 4 x 19 3 4 In 1521mm x 806 mm x 502mm WEIGHT 85 Lbs 39 Kg WEIGHT w WATER 535 Lbs 243 Kg GAL TO OVERFLOW 54 Gal 204 L MIN OPERATING GAL 49 Gal 186 L If a whirlpool do not make modifications to the whirlpool system or remove pump from factory mounting This could adversely affect the safety and performance of the whirlpool and void the warranty Do not handle or move the whirlpool by the pump motor or piping system BATHING WELL AT SUMP 20x 40 In 508mm x 1016mm BATHING WELL AT RIM 53 1 2 x 26 In 13
Download Pdf Manuals
Related Search