AMD PPC-L106T User's Manual
Contents
1. internal one external Each connector supports two IDE devices on two channels PIO modes 3 4 BIOS supports IDE PIO mode 0 4 DMA mode 0 2 and Ultra DMA33 simulta neously Default CF Slot set as Master e Parallel port One parallel port supports SPP EPP ECP parallel mode Serial ports Four serial ports with three RS 232 ports COMI 3 and 4 one RS 232 422 485 port COM2 All ports with 16C550 compatible UARTs Default COM4 reserved for Touch USB Supports four USB 2 0 2 x internal 2 x external e PCUISA bus expansion slot Accepts either one ISA or one PCI bus card Watchdog timer 256 level interval from 1 to 255 seconds Jumperless selection and software enabled disabled Battery 3 V 195 mA lithium battery for CMOS backup Solid State Disk SSD One 50 pin socket for one CompactFlash Type II storage card shared with one IDE channel PCI SVGA flat panel interface e Chipset AMD CS 5536 Display memory 1 5 4 MB share memory Display type Simultaneously supports CRT and flat panel displays e Display resolution Supports non interlaced CRT and LCD dis plays up to 800 x 600 256 K colors with 1 5 4 MB shared memory Audio function Audio Chipset ALC203 fully compliant AC 97 analog I O com ponent 16 bit stereo full duplex codec audio interface for microphone in line in and speaker out PCI bus Ethernet interface Chapter 1 General Information 3 e Ethernet Chipset Realtek2. Adapter Replacement To replace or service the PCM 9679 all in one CPU board and I O adapter complete the following steps 1 PA 3 Turn off the power to the PPC L106T Remove the rear protective cover see Figure 2 1 Install the PCM 9679 in the panel and screw in the eight screws see Figure 2 4 When the PCM 9679 is mounted in the panel plug and press the adapter into the socket see Figure 2 4 Some screws on the left connect the I O adapter to the PC and also connect the adapter to the PCM 9679 Screw the screws into the panel Note You may change the jumper settings for RS 232 422 485 before installing the PCM 9679 and I O adapter 20 PPC L106T User Manual a CU Figure 2 4 Installing removing the PCM 9679 VO adapter Chapter 2 System Setup 21 22 PPC L106T User Manual CHAPTER The Engine of the PPC L106T PCM 9679 Sections include Introduction Features Jumpers and Connectors CMOS clear Watchdog timer configuration COM2 RS 232 422 485setting Chapter 3 The Engine of the PPC L106T PCM 9679 3 1 Introduction The PCM 9679 s a highly reliable single board computer based on the AMD LX800 CPU It offers built in functionality comparable to a com plete industrial PC system including a VGA LCD controller network communications CompactFlash disk in a small 8 x 5 75 form factor For maximum performance the PPC L106T also supports aD
3. L106T back panel VO arrangement and cable connec tions A Power switch F COM ports B Parallel port G COM ports C PS 2 mouse connector H VGA port D Mic in Line out USB ports V2 0 E AC inlet J Ethernet Three RS 232 COMI 3 4 and one RS 232 422 485 COM2 Chapter 1 General Information 7 1 6 Cutout Suggestion The PPC L106T will stand on a shelf or a table or you can mount it into a panel Cutout panel dimensions are as follows 1 0 51500 12 47 247 00 9 70 Figure 1 3 PPC L106T panel mounting cutout dimensions 8 PPC LI06T User Manual 1 7 Mounting 1 7 1 Panel mounting If you decide to use a cutout within a panel to mount your PPC L106T we have included two panel mount brackets The brackets have two screws that fit in the keyhole slots on the panel PC Slide the PPC L106T backwards into the panel opening Attach the two mounting brackets by sliding the two screw heads into the keyhole slots on the rear cover Secure the PPC L106T against the back of the panel opening Figure 1 4 PPC L106T rear panel mounting brackets Chapter 1 General Information 9 1 7 2 Desktop stand optional An optional stand is available for mounting the PPC as a desktop PC The PPC L106T slides into the stand and is held in place by the screws pro vided The compactness of the desktop mounted PPC L106T saves desk space ee E is ee 2 3 Se al q fe ee z a ER Cs
4. O NI oO wo Pin Signal 2 V5_USB1 4 USB3_Z P 6 USB3_Z P 8 GND Appendix A 1 0 Pin Assignments 47 A 11 SMBUS Connector Default No Load Table A 11 CNS SMBUS Input Pin BIO N a 48 PPC L106T User Manual Signal V SMB GND SMB A CLK SMB A DAT
5. RTL8100C PCI local bus Ethernet con troller fully compliant with IEEE 802 3u 10 100 Base T speci fications Touchscreen optional Type Analog Resistive Infrared Resolution Continuous 4096 x 4096 Light Transmission 80 91 Controller RS 232 interface uses COM4 Optional USB interface Power Consumption lt gt V 200 mA 5 V 100 mA Software Driver Supports Windows CE Supports Windows CE XP XP Durability touches 3 Million 100 000 hrs in a lifetime Note The PPC L106T with the optionally installed touchscreen will share COMA Environment e Temperature 45 C 32 125 F e Relative humidity 10 95 40 C non condensing e Shock 10G peak acceleration 11 msec duration e Power MTBF 50 000 hrs Certification CE FCC Class B BSMI CCC 4 PPC LI06T User Manual 1 3 LCD Specifications Display type LCD 10 4 SVGA TFT 10 4 SVGA TFT Max resolution 800 x 600 Colors 262 K colors View angle 140 100 Dot size mm 0 264 X 0 264 Luminance cd m 230 400 Temperature C 0 50 VR controls Yes Yes Simultaneous mode Yes Yes Lamp Life hrs 90 000 hours The VR control is defined by hot key n DOS or BIOS mode as follows Ctrl Alt F3 Ctrl Alt F4 Chapter 1 General Information 5 1 4 Dimensions a 265 00 10 45 C Figure 1 1 PPC L106T panel PC dimensions 6 PPC L106T User Manual ON ne 4 O NY 1 5 I O Arrangement Figure 1 2 PPC
6. T compatible The medium type can be configured via the RSET8139 EXE program included on the utility disk The Ethernet port provides a standard RJ 45 jack The network boot fea ture can be utilized by incorporating the boot ROM image files for the appropriate network operating system The boot ROM BIOS files are combined with system BIOS which can be enabled disabled in the BIOS setup 2 4 6 USB ports The external USB device may be connected to the system though the 4 pin USB ports located on the rear side of the system unit The USB ports support hot plug in connection You should install the device driver before you use the device 2 5 Installing Software to the HDD Installing software requires an installed HDD Software can be loaded in the PPC L106T using any of four methods 2 5 1 Method 1 Use the Ethernet You can use the Ethernet port to download software to the HDD 2 5 2 Method 2 Use a USB Disk or USB CD ROM You can use a USB disk or USB CD ROM to download the software to your HDD 2 5 3 Method 3 Use the COM or parallel port Connect another PC to the PPC L106T with an appropriate cable and transmit the software to the PPC L106T 18 PPC LI06T User Manual 2 6 Exploded Diagram Figure 2 3 shows all the components and parts that make up the PPC L106T Use it as a guide when assembling and disasesembling your sys tem Figure 2 3 PPC L106T exploded diagram Chapter 2 System Setup 19 2 7 PCM 9679 and I O
7. WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F IT MAY DAMAGE THE EQUIPMENT The sound pressure level at the operator s position according to IEC 704 1 1982 is equal to or less than 70 dB A DISCLAIMER This set of instructions is supplied according to IEC 704 1 We disclaim all responsibility for the accuracy of any state ments contained herein Wichtige Sicherheishinweise l Bitte lesen sie Sich diese Hinweise sorgf ltig durch 2 Heben Sie diese Anleitung f r den sp teren Gebrauch auf 3 Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Verwenden Sie Keine Fl ssig oder Aerosolreiniger Am besten dient ein angefeuchtetes Tuch zur Reinigung 4 Die NetzanschluBsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein 5 Das Ger t ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Verletzungen hervorrufen 7 Die Bel ftungs ffnungen dienen zur Luftzirkulation die das Ger t vor berhit zung sch tzt Sorgen Sie daf r daB diese ffnungen nicht abgedeckt werden 8 Beachten Sie beim Anschlu an das Stromnetz die AnschluBwerte 9 Verlegen Sie die NetzanschluBleitung so daB niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden 10 Alle Hinweise und Warnungen die sich am Ger ten befinden sind zu beachten 11 Wird das Ger t ber einen
8. compact and highly integrated multimedia system lets you easily build a panel PC into your applications By incorporating the PPC L106T into your project your product development time will be shortened The PPC L106T is a compact network compatible PC with extensive features to control a dedicated system in a wide variety of applications Common industrial applications include factory automation systems pre cision machinery and production process control It is also suitable for many nonindustrial applications including terminal information systems entertainment management systems and car park automation systems Our panel PC is a reliable cost effective solution to your application s processing requirements 1 2 Specifications General e Dimensions W x H x D 342 x 265 x 92 4 mm 13 5 x10 4 x3 6 Weight 3 2 kg 7 1 lbs Power supply AC model 65 watts Input voltage 100 240Vac 2A 50 60 Hz Output voltage 5 V 3 5 A 12 V 4 A Safety UL CB CCC BSMI approved Disk drive housing Space for one internal 2 5 HDD e Front panel protection IP 65 NEMA 4 compliant Standard PC functions CPU AMD LX800 500 MHz processor on board e BIOS AWARD 4M bit Flash BIOS supports Plug amp Play APM v1 2 Chipset AMD CS 5536 2 PPC L106T User Manual e 2nd level cache 128 KB on CPU RAM One 200 pin SODIMM sockets accept 256 1024 MB DDR e PCI Bus Master IDE interface Supports two connectors one
9. l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspannung eine Besch di gung vermieden 12 Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Schlag aus l sen 13 ffnen Sie niemals das Ger t Das Ger t darf aus Gr nden der elektrischen Sicherheit nur von authorisiertem Servicepersonal ge ffnet werden 14 Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen a Netzkabel oder Netzstecker sind besch digt b Fl ssigkeit ist in das Ger t eingedrungen c Das Ger t war Feuchtigkeit ausgesetzt d Wenn das Ger t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen e Das Ger t ist gefallen und oder das Geh use ist besch digt f Wenn das Ger t deutliche Anzeichen eines Defektes aufweist 15 VOSICHT Explisionsgefahr bei unsachgemaben Austausch der Batte rie Ersatz nur durch densellben order einem vom Hersteller empfohlene mahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des Herstellers Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger DISCLAIMER This set of instructions is supplied according to IEC704 1 We disclaim all responsibility for the accuracy of a
10. no keyboard operation in embedded system applications without the system halting under POST Note that the mouse port on the PPC L106T is a PS 2 mouse port Note All but keyboard is the default setting 2 4 2 Mic in line out The PPC is equipped with a high quality audio interface which provides 16 bit CD quality recording and playback as well as OPL3 compatible FM music It is supported by all major operating systems and is com pletely compatible with Sound Blaster Pro The audio interface includes two jacks microphone in and line out See Fig 1 2 2 4 3 External VGA The PPC L106T can be connected to an external CRT monitor To con nect an external CRT monitor connect the monitor s VGA cable to the PPC 102 s VGA port and connect the monitor s power cable to an AC outlet The PPC L106T s external CRT display VGA connector is a standard 15 pin D SUB connector commonly used for VGA 2 4 4 Four serial COM ports Many available peripherals such as a serial mouse or an optional touch screen require connection to a serial port When an optional touchscreen is ordered with a PPC L106T it shares COM4 and COM4 is not avail able as a serial port Chapter 2 System Setup 17 2 4 5 Ethernet The PPC L106T is equipped with a high performance 32 bit Ethernet chipset which is fully compliant with the IEEE 802 3 100 Mbps CSMA CD standards It is supported by major network operating systems It is also both 100Base T and 10Base
11. 00 Ist Edition Printed in Taiwan November 2006 PPC L106T User Manual il FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with this user manual it may cause harmful interference to radio communications Note that even when this equipment is installed and used in accordance with this user manual there is still no guarantee that interference will not occur If this equipment is believed to be causing harmful interference to radio or television recep tion this can be determined by turning the equipment on and off If inter ference is occurring the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver e Connect the equipment to a power outlet on a circuit different from that to which the receiver 1s connected e Consult the dealer or an experienced radio TV technician for help Warning Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to op
12. 3 RS 232 serial port connector CN2 1 Table A 5 COM3 RS 232 serial port Pin Signal 1 DCD 2 RxD SE 3 TxD 3 26 4 DTR 6 O 5 GND 6 DSR 7 RTS 8 CTS 9 RI A 6 COM4 RS 232 serial port connector CN2 2 Table A 6 COM4 RS 232 serial port Pin Signal DCD RxD TxD DTR GND DSR RTS CTS RI O O0O NII BIW NM gt 44 PPC L106T User Manual LO CO NA A 7 COM2 Connector 12345 OOOO 6 7 8 9 Table A 7 COM2 Pin RS 232 RS 422 RS 485 1 DCD TX DATA 2 RX TX DATA 3 TX RX 4 DTR RX 5 GND GND 6 DSR 7 RTS 8 CTS 9 RI Appendix A I O Pin Assignments 45 A 8 Parallel port connector CN1 1 Table A 8 Parallel port connector Pin ON BR NI gt 0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Signal STROBE DO D1 D2 D3 D4 D5 D6 D7 ACK BUSY PE SLCT AUTOFD ERR INIT SLCTINI GND GND GND GND GND GND GND GND active low 46 PPC L106T User Manual o O O O O O O O O O O O O O O O O O O O o O o J0 U BW pO F O A 9 GPIO Connector Default No Load 2 4 6 8 1 1 3 5 7 Table A 9 CN7 GPIO Pin Signal V5 GPIOO GPIO1 GPIO2 GPIO3 O rd oO wo gt 0 9 Pin Signal GPIO4 GPIOS GPIO6 GPIO7 10 GND A 10 USB 3 USB 4 Connector Internal 2 4 6 8 135 7 9 Table A 10 CNT2 Internal USB 3 USB 4 Pin Signal V5_USB1 USB2_Z P USB2_Z P GND GND
13. DR SODIMM socket that can accept up to 1024 MB memory On board fea tures include an Ethernet interface audio interface socket for Compact Flash card Enhanced IDE interface that supports the Ultra DMA protocol one parallel port four serial ports RS 232 and RS 232 422 485 with DB 9 connectors and a mini DIN PS 2 keyboard mouse inter face An SVGA LCD display controller for LCD and CRT displays allows LCD screen resolutions up to 800 x 600 256 K colors The PCM 9679 complies with the Green Function standard and sup ports three types of power saving features Normal Doze and Sleep modes The display type configuration is done through software A single Flash chip holds the system BIOS and the VGA BIOS This minimizes the number of chips and eases configuration You can change the display BIOS s mply by programming the Flash chip Flash memory also offers faster data access and longer MTBF than mechanical disk drives and is an ideal solution for critical commercial or industrial applications The watchdog timer ensures the system will be reset if it stops due to a program bug or EMI problem 24 PPC L106T User Manual 3 2 Features e Ultra compact size single board computer as small as a 3 1 2 hard disk drive 145 mm x 102 mm e On board AMD LX800 CPU e Up to 1024 MB system memory via an SODIMM DDR e On board VGA LCD controller e On board 10 100Base T Ethernet interface dual LAN Optional Supports on board Compac
14. FF and its request IRQ is IRQ4 and COM2 s address range is 2F8 2FF and its interrupt IRQ is IRQ3 COM3 and COM4 are another set Their address and IRQ is the same as the COM1 COM2 set 30 PPC L106T User Manual Table 3 5 Serial port default settings Port Address Range Interrupt COM1 3F8 3FF IRQ4 COM2 2F8 2FF IRQ3 COM3 3E8 3EF IRQ10 COM4 2E8 2EF IRQ5 3 5 2 COM3 COMA4 pin 9 output setting J7 Table 3 6 COM3 4 pin 9 settings J7 Normal operation 5 V output 12 V output 8 10 12 8 10 12 8 10 12 EEE GE default setting Chapter 3 System Setup 31 32 PPC L106T User Manual UO Pin Assignments Sections include Chapter A I O Pin Assignments A 1 Keyboard connector CN5 1 Table A 1 Keyboard connector Pin Signal KB_DT N A GND 5 V KB_CK N A D O 2 0O Nj A 2 Mouse connector CN5 2 Table A 2 Mouse connector Pin Signal MS_DT N A GND 5 V MS_CK N A OI Bl Ww NM gt 42 PPC L106T User Manual A 3 VGA connector CN6 Table A 3 VGA connector Signal RED GREEN BLUE N A GND GND GND GND N A GND N A N A 13 HSYNC 14 VSYNC 15 N A H 5 UVP W N H O O0O J OD OI BR WwW NM gt NI AA COM1 RS 232 serial port CN1 2 Table A 4 COMI RS 232 serial port Pin Signal 1 DCD 3 2 RxD 2 gt 3 TxD 310 eis 4 DTR 50 9 5 GND 6 DSR 7 RTS 8 CTS 9 RI Appendix A I O Pin Assignments 43 A 5 COM
15. Options Installing I O Equipment e Installing Software to the HDD e Exploded Diagram e PCM 9679 and I O Adapter Replacement e Power Supply and Cooling Fan Replacement Chapter 2 System Setup 2 1 General The PPC L106T consists of a PC based industrial computer that is housed in a protective cover Your HDD DDR RAM and power supply and are all readily accessible by removing the rear panel Any mainte nance or hardware upgrades can be carried out easily after removing the rear panel Warning Do not remove the rear cover until you have verified that no power is flowing within the PPC L106T Power must be switched off and the power cord must be disconnected Every time you service the PPC L106T you should be aware of this 2 2 Preparing For First Time Use Before you set up the PPC L106T system you should have at least the following items ready Power cord in the accessory box e PS 2 keyboard PS 2 mouse for system software installation 1 e MS Windows NT etc 14 PPC LI06T User Manual 2 3 Installing Options 2 3 1 Removing Rear Panel Unscrew the eleven screws that secure the rear cover then remove the cover Y WI NONN Figure 2 1 Removing the rear panel Chapter 2 System Setup 15 2 3 2 Installing a primary 2 5 HDD internal You can attach one enhanced Integrated Device Electronics IDE hard disk drive to the PPC L106T s internal controller which uses a PCI local bus interfac
16. PPC L106T AMD LX800 processor based Panel PC with 10 4 TFT LCD flat panel display User Manual Copyright This document is copyrighted 2006 All rights are reserved The origi nal manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmit ted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual 1s intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties that may result from such use Acknowledgements Award s a trademark of Award Software International Inc AMD is a trademark of Advanced Micro Devices Inc IBM PC AT PS 2 and VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corp RTL is a trademark of Realtek Semi Conductor Co Ltd ESS 1s a trademark of ESS Technology Inc UMC is a trademark of United Microelectronics Corporation SMI is a trademark of Silicon Motion Inc Creative is a trademark of Creative Technology Ltd All other product names or trademarks are properties of their respective owners This manual is for the PPC L106T Part No 2006106T
17. Ye a Este Ki Di E ps Figure 1 5 PPC L106T desktop stand 10 PPC LI06T User Manual 1 7 3 Wall mounting optional An optional wall mounting attachment is also available for mounting the PPC at approximately 45 to a flat surface Installation instructions fol low l The wall mounting attachment is comprised of three parts one back bracket one support bracket and one mounting bracket 2 First attach the back bracket to the rear cover of the PPC L106T securing it in place with four of the philips head screws provided 3 Using a flat head screwdriver attach the support bracket to the back bracket using four of the flat head screws provided two on either side of the support bracket The sides of the support bracket should overlap the sides of the back bracket and the screws should secure one bracket to the other through the existing holes drilled into each bracket 4 Mount the mounting bracket on the wall or other flat surface The support bracket slides vertically from the top into the mounting bracket It can then can be secured to the mounting bracket by screwing one of the philips head screws provided through the cor responding holes at the tops of the mounting bracket and the sup port bracket Figure 1 6 PPC L106T wall mounting configuration Chapter 1 General Information 11 12 PPC LI06T User Manual CHAPTER System Setup Sections include General e Removing Rear Panel e Installing
18. e The advanced IDE controller supports faster data transfer rates and allows the IDE hard drive to exceed 528 MB The following are instructions for installation 1 Detach the rear panel and remove 2 Place the HDD in the appropriate location inside the PPC L106T and tighten the screws 3 Connect the cable included in this package 1x44 pin to 1x44 pin from the HDD to the PC board CN9 Make sure that the red blue wire corresponds to pin 1 on the connector which is labeled on the board Plug the other end of the cable into the enhanced IDE hard drive with pin 1 on the cable corresponding to pin 1 on the hard drive Warnings 1 Plug the other end of the cable into the HDD with pin 1 on the cable corresponding to pin Tonthe hard drive Improper connection will damage the HDD 2 Be careful not to damage the CPU board with your tools Figure 2 2 Installing a primary 2 5 HDD internal 16 PPC LI06T User Manual 2 4 Installing I O Equipment 2 4 1 PS 2 keyboard and PS 2 mouse The PPC L106T provides a PS 2 keyboard connector that supports a PS 2 style keyboard and a 5 pin DIN keyboard extension cable In most cases especially in embedded applications a keyboard is not used The standard PC AT BIOS will report an error or failure during power on self test POST after a reset if the keyboard is not present The BIOS standard setup menu allows you to select All But Keyboard under the Halt On selection This allows
19. e turning on the power supply This jumper is used to erase CMOS data and reset system BIOS informa tion The procedure for clearing CMOS is l 2 3 4 Turn off system Short pin 2 and pin 3 Return jumper to pins 1 and 2 Turn on the system The BIOS is now reset to its default setting Table 3 3 CMOS clear J3 Normal operation Clear CMOS 1 2 3 1 2 3 Gn UB default setting 3 5 COM Port Interface J6 J7 The panel PC provides four serial ports COMI 3 4 RS 232 COM2 RS 232 422 485 in one COM port connector 3 5 1 COM2 RS 232 422 485 setting J6 COM2 can be configured to operate in RS 232 RS 422 or RS 485 mode This is done via J6 Chapter 3 System Setup 29 Table 3 4 COM2 RS 232 422 485 setting J6 RS 232 2 4 6 8 10 12 14 16 18 BB B B CD o CD 135 7 9 11 13 15 17 RS 422 2 4 6 8 10 12 14 16 18 RSR Ka Gp 1 3 5 7 9 11 1315 17 RS 485 8 10 12 14 16 18 WER 13 15 17 default setting The IRQ and the address ranges for COMI 2 3 and 4 are fixed How ever if you wish to disable the port or change these parameters later you can do this in the system BIOS setup The table overleaf shows the default settings for the panel PC s serial ports COMI and COM2 are one set You can exchange the address range and interrupt IRQ of COMI for the address range and interrupt IRQ of COM2 After exchanging COM1 s address range is 3F8 3
20. e ent hee 27 CMOS Clear for External RTC OO 29 COM Port Interface J6 II 29 vil Chapter A A l A 2 A 3 A 4 A 5 A 6 A 7 A 8 A 9 A 10 A ll 3 5 1 COM2 RS 232 422 485 setting J6 rs 29 3 5 2 COM3 COM4 pin 9 output setting J7 31 VO Pin Assignments eeessssssssssnnnnnssssossnnssnneee 42 Keyboard connector CNS J in 42 Mouse connector CNI 2 cies Gd 42 VGA connector ChNo a a 43 COMI RS 232 serial port CN1I 2 43 COM3 RS 232 serial port connector CN2 1 44 COM4 RS 232 serial port connector CN2 2 44 COND CORE 45 Parallel port connector CNT I 46 GPIO Connector Default No Load 47 USB 3 USB 4 Connector Internal 47 SMBUS Connector Default No Load 48 PPC L106T User Manual Vill CHAPTER General Information This chapter gives background information on the PPC L106T Sections include Introduction e Specifications e LCD Specifications Dimensions e I O Arrangement Cutout Suggestion e Mounting Chapter 1 General Information 1 1 Introduction The PPC L106T is a 10 4 LCD Panel PC with an AMD LX800 CPU that is designed to serve as a human machine interface HMI It is a PC based system with 10 4 color TFT LCD display on board PCI Ethernet multi COM port interfaces and a 16 bit audio controller This simple com plete
21. e equipment the socket outlet must be installed near the equip ment and must be easily accessible Please keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or let ting t fall could cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVI RONMENT
22. erate the equipment iii Packing List Before you begin installing your card please make sure that the following materials have been shipped e PPC L106T series panel PC e Accessories for PPC L106T Keyboard extension cable 5 pin DIN female to 6 pin PS 2 male HDD flat cable 44 pin 8 cm Power cord 1 8 m USA type HDD bracket Driver Utility CD ROM disk Screws Warranty card If any of these items are missing or damaged contact your distributor or sales representative immediately Additional Information and Assistance Step 1 Visit the our web site where you can find the latest information about the product Step 2 Contact your distributor sales representative or customer service center for technical support if you need additional assistance Please have the following information ready before you call e Product name and serial number e Description of your peripheral attachments e Description of your software operating system version application software etc e A complete description of the problem e The exact wording of any error messages PPC L106T User Manual iv Safety Instructions l Ze 3 10 11 12 13 14 15 Please read these safety instructions carefully Please keep this User Manual for later reference Please disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggabl
23. ny state ments contained herein PPC L106T User Manual vi Chapter Chapter Chapter 1 1 1 12 1 3 1 4 1 5 1 6 1 7 2 1 22 2 3 2 4 29 2 6 24 3 1 32 3 3 3 4 3 5 Contents General Information ss 2 Introduction 2 SDECILICATIONMS a een nn 2 LCD Specification Senni 5 DIMENSIONS AAA a ND 6 LO Arrangement ebe 1 Cutout Guggeston nenn 8 A EE H LE Pamlmountin e er sn ne 9 1 7 2 Desktop stand optional 10 1 7 3 Wall mounting optional 11 System SUD ces 14 E A an teacate ted 14 Preparing For First Time Use 14 Installing Options an 15 Dal Removn Rear Panels o as 15 2 3 2 Installing a primary 2 5 HDD internal 16 Installing VO Equipment osain 17 2 4 1 PS 2 keyboard and PS 2 mouse 17 242 Mican MEM ii 17 2 43 External VGA na esse 17 24 4 Four serial COM ports 17 ZAS EM Nr 18 2 4 6 USB pont 18 Installing Software to the HDD 18 2 5 1 Method 1 Use the kdermert nen 18 2 5 2 Method 2 Use a USB Disk or USB CD ROM 18 2 5 3 Method 3 Use the COM or parallel port 18 Exploded Diagran ns nie 19 PCM 9679 and I O Adapter Replacement 20 The Engine of the PPC L106T PCM 9679 24 IVER O GULCH ON EE 24 RELL E S EN E ee eeneg 25 Jumpers and Connectors 26 33 1 SA ee do da 26 3 32 A A cca eee eset testcase 27 333 ACOMME CLOLS yaa ht
24. onnector SLOT1 PCI ISA bus expansion connector 3 3 3 Connectors The table below lists the function of each of the board s connectors Table 3 2 Panel PC connectors Label Function J1 Inverter power connector J2 Flat panel display connector J3 Primary IDE hard drive connector J4 Keyboard connector J5 Internal touchscreen connector CN1 SODIMM socket CN2 CompactFlash Disk secondary IDE connector CN3 CD IN CNA UO board connector CNS UO board connector CN6 Power FAN power connector CN External KBT2 CN8 CPU FAN power connector CN10 Power Switch CN20 Speaker and Microphone connector Reserved PS1 Power test connector Reserved JS2 Brightness VR Reserved Chapter 3 System Setup 27 BTI J6 Figure 3 1 Jumpers on the PPC L106T motherboard Figure 3 2 Connectors on the PPC L106T motherboard 28 PPC L106T User Manual 3 4 CMOS Clear for External RTC J3 Warning To avoid damaging the computer always turn off the power supply before setting Clear CMOS Set the jumper back to Normal operation befor
25. tFlashTM socket e Built in Enhanced IDE AT bus hard disk drive interface Four serial ports three RS 232 one RS 232 422 485 or infared select able e Supports One Mini PCI socket Supports 4 USB 2 0 2 external 2 internal e Supports 8 bit GPIO Chapter 3 System Setup 25 3 3 Jumpers and Connectors 3 3 1 Setting jumpers You can configure your panel PC to match the needs of your application by setting jumpers A jumper is the simplest kind of electrical switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either pins 1 and 2 or pins 2 and 3 The jumper settings are schematically depicted in this manual as follows 3 open closed closed 2 3 open closed closed 2 3 If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representative before you make any changes 26 PPC L106T User Manual 3 3 2 Jumpers The table below lists the function of each of the board s jumpers Table 3 1 Jumpers and their functions S1 Reset Button J2 SMBUS Power Setting J3 CMOS Clear J4 AT ATX Setting JG COM2 RS232 422 485 Setting J7 COM3 4 Pin9 output type setting BT1 Battery C
Download Pdf Manuals
Related Search