Airaid 300-765 User's Manual
Contents
1. by ARIS 1 D INSTALLATION INSTRUCTIONS 4300 765 AIRAID JR KIT 300 965 AIRAID MIT 2005 07 DODGE DAKOTA 4 7L V 8 2006 07 MITSUBISHI RAIDER 4 7L V 8 Thank you for purchasing the Airaid Intake System Please read the instruction manual carefully before proceeding with the installation Contact Airaid 800 498 6951 8 00 AM 5 00 PM MST weekdays for questions regarding fit or instructions that are not clear to you Your Airaid Intake System was carefully inspected and packaged Check that no parts are missing or were damaged during shipping If any parts are missing contact Airaid The air filter element is protected from direct exposure to water and debris care should be taken not to drive through deep water WATER INGESTION IS THE DRIVERS RESPONSIBILTY The air filter is reusable and should be cleaned using the Airaid Filter Tune Up Kit periodically Thank you for selecting Airaid Se KR Sege d ai PELU x F Packing List Tools Required for this Installation 850 175 Airaid Premium Filter 1 Flat Head Screwdriver or KIT965T Modular Intake Tube 1 5 16 Socket amp Ratchet KITRDCROI1 Silicone Reducer Hose 1 10mm Socket KITHUMPHS02 Urethane Hump Hose l KIT765HP Hardware amp Instructions 1 KITHS8 48 Hose Clamp 1 KITHS52 52 Hose Clamp 1 KITHS60 60 Hose Clamp 2 KITGRMT03 Grommet 1 1 Disconnect negative battery cable Loosen hose clamp on intake tube at the factory airbox end For Jr Kit replace the facto2. tary opr gag Porfarmance i i F d AT i canes dai LaLa Hi eh pyg Conse Wann am CHL ARE II mi fn GUR af is ML LEU sna fl Nite Th H P d Ki Clean your Airaid el act SFore ful afr flows G wg otain opetimant ens KE WT ET TG CAUTION Fjammat a 7 UP Pa IE ok Pl d KAS Me w UID ADO Inflanall rc E te de pate ele twill FI SWKEEGTEISEOTIT NI I H been wir peas Duc Ges e Atri ho a HS RA oe TENTION Oe C ik s piaia Ete ER HI Ti nan Jel ES Ji a d di an Fri ber TRI A HET RBE DU Gee P N 790 5 50 Instructions Revision Date 07 16 08
3. ry air filter with the Airaid Premium Filter provided 2 Disconnect the intake air temperature sensor by squeezing the tab on the connector 3 With the 10mm socket remove 2 bolts from the base of the resonator 4 Remove the resonator and tube from the vehicle 5 With the resonator turned over carefully remove the air temp sensor by pushing in and turning counter clockwise 6 Install the urethane hump hose on the factory airbox with the two 60 hose clamps Leave clamps loose Next install the reducer small side first with the 48 hose clamp on the throttle body Install the 52 hose clamp on the outside of the reducer and leave loose tallation Instructions Read M Ins e 7 Install the grommet into the hole in the MIT as shown 8 Carefully install the air temp sensor into the grommet installed in step 7 Make sure it goes all the way in 9 Install the MIT into the hump hose first and then into the reducer Adjust the MIT so that it s up against the throttle body and then tighten all four hose clamps Reconnect the air temp sensor 10 Double check your work to be PROUDLY MADE IN THE certain that all nuts bolts and clamps are securely fastened 11 Reconnect the negative battery cable Before a gh d a sl HUE i Don t Forget Your AIRAID Filter Tune Up Kit E oie ee Crear vour Airafd at wf Foo Tataro futi air How v i
Download Pdf Manuals
Related Search