ADTRAN 234 User's Manual
Contents
1. 7 8 Unused CONSOLE PORT PINOUT Pin Name Description 1 DCD Data Carrier Detect output 2 RD Receive Data output 3 TD Transmit Data input 4 DTR Data Terminal Ready input 5 SG Signal Ground 6 DSR Data Set Ready Tied to pin 1 output 7 9 Unused 8 CTS Clear to Send Tied to pin 1 output WAN SHDSL NETWORK PINOUT RJ 45 Pin Name Description 1 Tip 2 4 wire Loop 2 Pair Tip 2 Ring 2 4 wire Loop 2 Pair Ring 3 Not connected 4 Tip 1 2 wire Pair Tip 4 wire Loop 1 Pair Ring 5 Ring 1 2 wire Pair Ring 4 wire Loop 1 Pair Ring 6 8 Unused Quick Start Guide 61200708L1 13B January 2005 Technical Support 1 888 4ADTRAN or 1 256 963 8716 Copyright 2005 ADTRAN All Rights Reserved2. For more detailed documentation visit us online at www adtran com ADRAN Quick Start Guide TOTAL ACCESS 234 SHDSL NTU P N 1200708L1 NETWORK ETHERNET CONSOLE OCG CONNECT THE CONSOLE INTERFACE CONFIGURE GATEWAY IP ADDRESSES SUBNET MASK Before connecting to the Total Access 234 console interface you will need the following items VT100 Configure the Gateway IP addresses and subnet mask by following terminal or PC with VT100 terminal emulation software and a straight through serial cable with a DB 9 these steps If you are not sure what IP address to assign please male connector on one end and the appropriate interface for your terminal or PC on the other contact your network administrator 1 n nN male connector of your serial cable to the console port on the rear 1 Enter enable to activate the Enable command security mode 2 Connect the loose end of the serial cable to the VT100 terminal or PC with terminal 2 When prompted enter the enable password if configured emulation software 3 Enter config terminal to activate the Global configuration mode 3 Open a VT100 terminal session to the Total Access 234 using the following settings 4 Enter bre lan gw 10 26 12 12 wan gw 100 26 12 12 mask 9600 baud 8 data bits no parity bits and 1 stop bit Press lt Enter gt to activate the 255 255 255 0 to assign LAN and WAN Gateway IP addresses and subnet mask ADTRAN Command Eine Intenace OL Note Underlined text rep
3. resents example entries only Modify them to match your configuration 5 Enter exit to return to the Enable configuration mode SPECIFICATIONS DC Input Power 12 VDC nominal 8 5 VDC min 18 VDC max ITU T standards G 991 2 6 Enter copy running config startup config to save the running Diagnostics amp Test Self diagnosis local loopback remote loopback configuration to the unit s non volatile memory NVRAM EMC Emissions EN55022 1998 Class B FCC Part 15 Class B FEATURES EMC Immunity Power EN55024 1998 EN61000 3 2 EN61000 3 3 Telstra 1563 K 21 2004 One integrated EIA 232 configuration port DCE penises Panning plane One integrated 10 100BaseT Ethernet port Electrical Safety EN60950 AS NZS 60950 UL60950 3rd ed CSA C22 2 No 60950 3rd ed IEC 60950 CB Scheme e 2 Wire 4 Wire SHDSL interface Telecom S043 2 G 991 2 WAN Protocol ATM Environmental Operating Temp 0 C to 50 C Storage Temp 20 C to 70 C gt Command Ling Intertaee GC e Management EOC CLI using Virtual Terminal e Front panel LEDs e Wall mounting available with additional parts Note No stacking should be done at 50 C Up to three units can be stacked at room temperature Humidity 95 percent noncondensing Dimensions 9 3 inches W x 2 1 inches H x 6 1 inches D Connectors SHDSL Port RJ 45 135 ohms TNV 3 rated 10 100BaseT Ethernet RJ 45 Console Port DB 9 female Power Input Kycon KPJ 3S snap amp lock or equivalent W ARNING Table
4. standoff cannot be used with this unit Quick Start Guide 61200708L1 13B January 2005 Technical Support 1 888 4ADTRAN or 1 256 963 87 16 Copyright 2005 ADTRAN All Rights Reserved ADRAN Quick Start Guide TOTAL Access 234 LEDs TOTAL ACCESS 234 SHDSL NTU For more detailed documentation visit us online at www adtran com P N 1200708L1 10 100BASET ETHERNET PORT PINOUT LED Color Indication PWR Off No power present Green solid Power present SHDSL Off Unit is powered off Green solid Port is trained with no active alarm conditions Yellow solid Port is trained with minor active alarm condition Red solid Port is attempting to train or is trained with a major alarm condition LLOOP Off No local loop is active Red solid A local loop is active RLOOP Off No remote loop is active Red solid A remote loop is active BERT Not applicable with this product LNK Off No Ethernet link present Green solid The 10BaseT Ethernet link is up Yellow solid The 100BaseT Ethernet link is up TD Off No transmit activity on Ethernet port Green blinking Transmit activity on Ethernet port RD Off No receive activity on Ethernet port Green blinking Receive activity on Ethernet port Pin Name Description 1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive 45 Unused 6 RX2 Receive Negative
Download Pdf Manuals
Related Search