ADT Security Services D7412 User's Manual
Contents
1. 78 if all doors are at anormal state and are available If a door is not at a normal state the number of the door will be replaced with a symbol indicated in the chart above Enter the number of the door you wish to unlock then press ENT This door will be unlocked and the display will change to reflect the new status of the doors For example if you wanted to unlock Door 4 at the following prompt UNLOCK DOOR 12345678 press 4 then ENT The display will read UNLOCK DOOR 123U5678 This indicates that all doors are at a normal state except for Door 4 which is unlocked Press ESC to leave this subfunction or enter another door number to unlock SECURE DOOR 13 14 15 16 If you wish to secure a door to prohibit access to users regardless of their access authority level at the CYCLE DOOR prompt press PREV to enter the SECURE DOOR subfunction The display will read SECURE 12345678 if all doors are at a normal state and are available If a door is not at a normal state the number of the door will be replaced with a symbol indicated in the chart above Enter the number of the door you wish to secure then press ENT This door will be secured and the display will change to reflect the new status of the doors For example if you wanted to secure Door 5 at the following prompt SECURE DOOR 12345678 Press 5 then ENT The display will read SECURE DOOR 1234X678 This indicates that all doors are at a normal state except2. A 1 is displayed If you wish this user number to be valid in Area 1 press ENT If not press NEXT 11 AUTH LEVEL is displayed Assign the authority level you wish the user number to have for this area and press the ENT key Be sure to record this information 12 VALID AREA 2 is displayed Enter the information as necessary for the areas in the scope of the command center by following steps 10 and 11 for each area up to 8 areas LEVEL ADDED or LEVEL CHANGED will be displayed when all area assignments have been made Press ENT On Systems With Access Control 13 SUB USER ID is displayed Press ENT SUB USER is displayed Enter 1 2 or 3 for the desired Sub User and press enter 14 PRESENT CARD is displayed Present the card token at the reader and wait for the tone After the tone is sounded the display will read CARD ADDED or CARD CHANGED if the Sub User number already existed NOTE At the end of each function you can press ESC to return to the ENTER USER prompt Press ESC again to return to idle text D9412 D7412 Owner s Manual Supplement Page 9 33267D 12 97 33267D 12 97
3. Security System Owner s Manual Supplement Introduction This reference supplements the Security System Owner s Manual 71 06633 000 with the Function List features for the D9412 D7412 The instructions for the commands listed in this reference are intended to replace those instructions in the Security System Owner s Manual Please refer to the Owner s Manual for the operation of your new security system and its other basic Function List features NOTE This supplement should be placed inside the Security System Owner s Manual Access Level Control uz2200002u20000000u0n00n0nnnnnnnunnnannnnnnnnnnn 3 Door Control Command 46 ns20u00000nn0000000nnnnnnnnnnnnnnnnnnnnnn 5 Cycle Door a ea ie 5 Unlock DoTaN EEE ATE nonanonn nan ona cnn ona ccn nana 6 Secure DOON Aa eun eaha abatido Pocitos 6 Delete User Command 53 ccccccccconncnococnananananananonocononnnnananananana 7 Add Change User Command 56 sscccceccesssseeeeeeeeeesseeeeesees 9 33267D 12 97 ACCESS LEVEL CONTROL Description Use this function to manually enable disable access authority levels assigned to users This function can be used to temporarily disable a user s access level instead of deleting and adding the user O I have this feature LJ I do not have this feature Using Access Level Control 1 Ensure the display shows idle disarmed text 2 Press the MENU key to enter the Function List then press NEXT repeatedly un
4. cle through the three sub functions by pressing PREV and NEXT CYCLE DOOR 5 If you wish to momentarily unlock an access door to allow a person into an area press ENT at the CYCLE DOOR prompt 6 The display will read CYCLE 1 2 3 45 6 7 8 if all doors are at a normal state and are available If a door is not at a normal state the number of the door would be replaced with a symbol indicated in the chart below Door is not active not in scope or user does not have access level authorit Door is on timed door sequence aa Strike and shunt are latched active held open U X Strike and shunt are deactivated secured F There is a problem with the door Call your security company 7 Enter the number of the door you wish to cycle then press ENT This door will be cycled and the display will change to reflect the new status of the doors For example if you wanted to cycle Door 3 at the following prompt CYCLE DOOR 12345678 press 3 then ENT The display will read CYCLE DOOR 12C 45678 This indicates that all doors are at a normal state except for Door 3 which is cycled 8 Press ESC to leave this subfunction or enter another door number to cycle D9412 D7412 Owner s Manual Supplement Page 5 33267D 12 97 UNLOCK DOOR 9 10 11 12 If you wish to unlock a door to allow free access at the CYCLE DOOR prompt press NEXT to enter the UNLOCK DOOR subfunction The display willread UNLOCK 123456
5. e displayed allowing for confirmation Press ENT If this is not the user you wish to delete press the NEXT or PREV key until the correct user name appears then press the ENT key 6 The display will now read DELETE USER Press ENT if you wish to have this user deleted and USER DELETED will be displayed If the user number is not in the system NOT IN USE will be displayed If you made an error and do not wish to delete this user press ESC D9412 D7412 Owner s Manual Supplement Page 7 33267D 12 97 ADD CHNG USER COMMAND 56 Description Use this function to add or change a passcode card without assistance from your security company Before adding or changing a passcode card you will need to know which user numbers are available the authority level you want to assign to the new user and the areas in which the passcode card will be valid O I have this feature O I do not have this feature Using Add User 1 Ensure the display shows idle disarmed text 2 Press the COMMAND bar The display shows SYSTEM COMMAND 3 Press 5 and 6 NOTE You may also use the Function List in place of steps 2 and 3 to initiate this function Press the MENU key to enter the Function List then press NEXT until you reach the ADD CHNG USER prompt Press ENT The display shows ENTER USER Key in the user number and press ENT 5 The display shows USER Y or user text such as the name of the user if this feature was programmed into your
6. for Door 5 which is secured Press ESC to leave this subfunction or enter another door number to unlock NOTE Each of these subfunctions act as a toggle To return a door to its normal state follow the same procedure you used to change its state For example if Door 3 is secured and you wish to return it to its normal state at the SECURE DOOR prompt enter 3 and press ENT The door will no longer be secured and the X will be replaced with the number 3 D9412 D7412 Owner s Manual Supplement 33267D 12 97 Page 6 DELETE USER COMMAND 53 Description Use this function to delete a personal passcode from your system without assistance from your security company You need to know the user number for the passcode you want to delete O I have this feature O I do not have this feature Using DEL USER 1 Ensure the display shows idle disarmed text 2 Press the COMMAND bar The display shows SYSTEM COMMAND 3 Press 5 and 3 NOTE If you prefer you may use the Function List in place of steps 2 and 3 to initiate this function Press the MENU key to enter the Function List then press NEXT repeatedly until you reach the DEL USER prompt Press ENT 4 The display shows DEL USER Key in the user number and press ENT If you do not know the user number press the NEXT key go to step 6 5 USER or user text such as the name of the user if this feature was programmed into your system by your security company will b
7. system by your security company to allow for confirmation Press ENT if the correct user number or user name 1s displayed Press ESC if not 6 ADD PASSCODE is displayed If the user number already exists CHANGE PASSCODE is displayed Press ENT ENTER NEW CODE is displayed Enter the new passcode followed by ENT ENTER AGAIN is displayed Enter the new passcode a second time for confirmation Press ENT The display will read PASSCODE ADDED or PASSCODE CHANGED if the user number was already in the system NOTE The system will not accept a passcode that is within two digits of an existing passcode This is to avoid conflicts with duress passcodes For example if passcode 123 is already programmed in the system the system will not accept 121 122 124 or 125 as passcodes On Systems With Access Control 7 If your system includes access control features such as card readers at doors etc the following prompt will be displayed ADD CARD CHANGE CARD will be displayed for users who already have cards 8 If the user is to have card token access to the building or area press ENT PRESENT CARD will be displayed Present the card at the card reader and wait for the tone If the card token is read correctly a tone will sound and the command center will display CARD ADDED or CARD CHANGED if the user already had a card token Press ENT 9 ADD LEVEL CHANGE LEVEL If the user number already exists is displayed Press ENT 10 VALID ARE
8. til you reach the CHANGE LEVEL CTL prompt Press ENT 3 ACCESS LEVEL CTL is displayed to remind you that you are affecting the authority levels of cards tokens and not passcodes Press ENT 4 ENTER LEVEL is displayed Enter the access authority level number and press ENT 5 If the access level is currently disabled LEVEL ENABLE is displayed If the access level is currently enabled LEVEL DISABLE is displayed Press ENT to accept the choice ENTER LEVEL is displayed again When you are finished press ESC D9412 D7412 Owner s Manual Supplement Page 3 33267D 12 97 DOOR CONTROL COMMAND 46 Description There are three sub functions within the door control function They are CYCLE DOOR UNLOCK DOOR and SECURE DOOR CYCLE DOOR momentarily unlocks a door to allow a person into an area UNLOCK DOOR unlocks a door to allow free access SECURE DOOR unlocks a door and prohibits access regardless of a user s authority level O have this feature O I do not have this feature Using Door Control 1 Ensure the display shows idle disarmed text 2 Press the COMMAND bar The display shows SYSTEM COMMAND 3 Press 4 and 6 NOTE If you prefer you may use the Function List in place of steps 2 and 3 to initiate this function Press the MENU key to enter the Function List then press NEXT repeatedly until you reach the DOOR CTRL prompt Press ENT 4 The first sub function that will appear is CYCLE DOOR You can cy
Download Pdf Manuals
Related Search