Pyle PLCD51BT
Contents
1. 14 2 Function of controls on main unit or remote control 15 AUXIN Operation nici 17 Troubleshooting nnne nnne 18 nnne nnns 19 INSTALLATION STEPS 1 Remove 2 screws for protecting deck 1 Remove chassis from the Slide Bracket Housing as follows KEY PLATE PLASTIC TRIM OUT KEY PLATE z If you want to remove the chassis from the Slide Bracket Housing first remove the Plastic trim from both sides then insert 2 Key Plates into the left and the right side of the chassis as illustrated 2 Remove 2 screws protecting the deck as illustrated on the right 2 Connecting all wires 1 Re insert the chassis into the Slide Bracket Housing 2 Remove the control panel from the chassis as follows A Press REL button to detach the control panel REL button B Hold the right end of the control panel to pull rightward a little and then remove it 3 Connecting all wires as bellows REAR AUDIO OUT RCA JACK R red FRONT AUDIO OUT RCA JACK R red RADIO ANTENNA JACK ESSE REAR AUDIO OUT RCA JACK L white FRONT AUDIO OUT RCA JACK L white Lu I D2. PWR button To power main unit on short press the PWR button on the control panel or on the remote control To power main unit off long press the PWR button on the control panel or short press the PWR button on the remote control VOL knob or VOL amp VOL button To increase or decrease volume level MUTE button To cancel or resume sound long press the MUTE button on the control panel or long press the MUTE button on the remote control SEL button To switch between VOL volume BAS bass TRE treble BAL balance FAD fader EQ LOUD MONO STEREO in radio mode LOC DX in radio mode and BT press the SEL button repeatedly After selecting a desired mode rotate the VOL knob or press the VOL or VOL button to set it To switch between TA SEEK ALAR MASK AL DP RETUNE S L and VOL 25 long press the SEL button to switch on TA SEEK ALAR then short and repeatedly press the SEL button After selecting a desired mode rotate the VOL knob or press the VOL or VOL button to set it DISPorCLK button To display clock time briefly press the CLK button on control panel or short press the DISP button on remote control To set clock time first long press the CLK button to flash hour and rotate the VOL knob or press the VOL or VOL button to adjust the hour then briefly press the SEL button to flash minute and rotate the VOL knob or press the VOL or VOL button to adjust the minutes fi
3. Fuse is blown Replace fuse Disc cannot Another disc is already in the Remove the disc in the player be loaded player then insert a new one The disc had been inserted Insert the compact disc with Di t SE upside down the label facing upward be read Compact disc is extremely Clean the disc or try to play a dirty or defective new one Temperature inside the Cool off until the ambient car is too high temperature returns to normal Volume is turned down Adjust volume to a desired level Wiring is not properly Check wiring connection connected 1 Built in microcomputer 1 Press the RESET button is not operating properly O t per M due to noise 2 Reinstall the front panel do not 2 Front panel is not properly won fixed into its place 3 Do not use the player until car has 3 Car interior is extremely hot been driven for a while to cool off Saud skibs Installation angle is more than Adjust installation angle 30 degrees to less than 30 degrees Disc is extremely Clean compact disc try to dirty or defective play a new one Radio does not work Antenna cable is not Insert antenna cable firmly connected Automatic radio Select a station manually station selection Signals are too weak does not work 18 SPECIFICATIONS GENERAL Power Supply DC 12V Current consumption cece cece cece cee ee 10A MAX Maxim
4. audio com aai USB CARD PZA S a dL d Bluetooth sw EA PLCD51BT Capabie Device amp mem PYLE m SIM anne a 28 8 ta USB SD CARD amp MP3 COMPATIBLE In Dash AM FM MPX Receiver w MP3 Playback amp USB SD AUX Inputs USER S MANUAL Content Installation 5 2 General information about remote 6 1 Removing insulating sheet usus 6 2 Replacing the lithium CEll een 6 3 Note about using the remote 6 4 Warning about lithium cells of remote control 6 Locations and Names of 1 7 1 Locations and Names of controls on main 7 2 Locations and Names of controls on remote control 8 General operation cerei cine rn ined oninia uou o aaa oa Nn aa oo ann 9 Radio operatiOn eene rere en anna an nn Hann ann ann se onda 10 BT operation ciment c none 12 Disc USB card operation ri 14 1 Loading or unloading a disc USB or card 14 1 1 Loading a disc USB or card ri 14 1 2 Unloading a disc USB
5. 2 LL 150 CONNECTOR BLUE AUTO ANTENNA YELLOW CONSTANT 12 VOLTS ES GROUND B RED IGNITION SWITCH FRONT WHITE GREY FRONT Lch Rch SPK WHITE BLACK GREY BLACK REAR GREEN VIOLET REAR Lch GREEN BLACK VIOLET BLACK 1 Must use 4 ohms impedance of speakers 2 Before finishing wiring do not attach control panel onto chassis 3 Maximum current of auto antenna is 200mA 4 Attaching the control panel onto the chassis A Align and thrush the bulge of the control panel into the hollow of the chassis How to clean panel connector Frequent detachment will cause the panel connectors to deteriorate To minimize deterioration periodically wipe the panel connector with a clean soft dry cloth 5 Test to make sure that it works properly 3 Instal the main unit according to the installation diagram on the next page 1 Mount the main unit in A V position in vehicle 2 Bend tabs of the sliding metal housing where necessary to ensure that the front part of main unit is fixed 3 Use a metal strap to fix the rear part of the chassis Uninstalling the main unit 1 Remove the metal strap from the main unit 2 Remove the plastic trim frame from the main unit 3 Insert a key plate into the left and the right side of the main unit and draw the main unit out of the sliding metal housing 4 Installation diagram SPRING WASHE
6. To play files on a disc insert a disc with label surface up into Kear iore the disc slot then it will play automatically DISCS PRECAUTIONS 1 Handle a disc by its edges do not touch the surface of play side 2 Before inserting a disc wipe the disc outwards from the disc centre with a clean soft dry lint free cloth Do notuse solvents thinners Such as petrol benzine or cleaners 3 After taking a disc out of the disc slot put the disc inside the disc case to keep it clean 4 Do not stick paper ortape on the disc surface If there is glue or adhesive on the disc surface wipe it off before using A To play files in a USB open the USB port cover then insert the USB storage into the USB port it will play files in the USB automatically To play files in a card press the REL button to detach the control panel and remove it then insert the card into the card slot as illustrated finally it will play files in the card automatically Label surface up 1 2 Unloading a disc USB or card To unload the disc in the disc slot use STOP button to stop playback and then press EJECT button to eject disc and then remove it 14 To unload the USB storage use STOP button to stop playback then remove the USB storage To unload the card in the card slot use STOP button to stop playback Press REL button to detach the control panel push the card to release it and then pull it ou
7. desired band then press one of the 1 6 buttons to find it and listen to it To preset current station on a memory bank long press one of the 1 6 buttons PTY button Pressing the PTY button on remote control or pressing the PTY button on control panel can switch between PTY music group PTY speech group and OFF When PTY group is on pressing one of 6 number 1 6 buttons can select one of typed programs After selecting one of typed programs it will automatically search for a station broadcasting the selected typed program If no any stations broadcasting the typed program exist it will return back to normal station TA button when you press the TA button on the remote control or long press the TA button on the control panel TA function is activated and TA symbol appears in the display press or long press it again to turn off 10 During radio operation FM frequency band the search for a traffic an nouncement station is started automatically TA SEEK If an FM station is being received which transmits the latest traffic announcements from time to time the TP display lights up If an FM station is being received which transmits the latest traffic announcements automatically interrupt CD operation the word TRAFFIC appears in the display The volume level is increased to the minimum value for the transmission of traffic announcements After the traffic announcements has finished the program that was previous
8. R PLAIN WASHER TAPPING SCREW SLIDE BRACKET HOUSING General information about the remote control 1 Removing insulating sheet The remote control comes with an insulating sheet attached to the underside of the remote control as illustrated on the right The remote control is disabled and will not work until the insulating sheet is removed SA Replacing the lithium cell If the electric energy of the lithium cell is weak replace it as illustrated on the right Press and hold the movable block in the direction indicated by arrow 1 atthe same time pull the cell holder out of the remote control in the direction indicated by arrow 2 a Replace the old cell with anew one with polarity side upward Insert the cell holder into the remote control again RESP Note about using the remote control o 4 Face the emitting window of the remote control towards the sensor window of the unit Operation angle for front panel About 30 degrees The distance between the emitting window of the remote control and the sensor window of the unit lt 5M Warning for lithium cells of remote control 1 2 3 Cell leakage may cause damage to remote control Do not throw cells into fire it may cause an explosion To avoid accidents keep cells out of reach of children Locations Names of controls 1 Locations and Names of controls on main unit eoo oee
9. ch INT mode on or off RPT button During CD playback it can switch repeat mode between RPT ONE RPTALL or RPT OFF During MP3 WMA playback pressing RPT button can switch repeat mode between RPT ONE RPT DIR RPTALL or RPT OFF RDM button To switch RDM mode on or off 10 and 10 buttons To skip to previous or next 10th track 103 and BAND buttons To display ID3 information and so on such as FILE FOLDER TITLE ARTIST ALBUM YEAR and COMMENT press the ID3 or BAND button Depend on the used media 16 AUX IN Operation 1 Use an audio cable to connect the car audio system and the external audio system through the AUX IN jack on the control panel of the car audio system and the Audio Out jack of the external audio system Ground Right Left 2 Play the external audio system and use the MODE button to enter AUX IN mode for the car audio system In AUX IN mode the external audio system uses the car audio system as an amplifier 3 InAUX IN mode you can use SEL VOL VOL VOL knob MUTE EQ and LOUD buttons to adjust sound 17 Troubleshooting During playback if your player has a problem use this guide to try and resolve the problem If you are unable to solve the problem consult an authorised dealer or service centre Symptom Cause Solution Car ignition is not on Switch ignition key to ACC No power
10. e phone audio to your mobile phone press the button on the control panel or press the button on remote control Adjust volume level during phone talking During phone talking use VOL knob or VOL and VOL buttons to adjust volume level use MUTE button to mute sound buttons they perform as buttons on mobile phone BT MUSIC Pressing MODE button enter BT AUDIO mode and display BT AUDI the LCD 2 When using your mobile phone with BT function to play audio video if it is paired and connected with the BT device of the car audio system the audio of the mobile phone will change into the car audio system The BT device ofthe car audio system support A2DP if your mobile phone with BT function support A2DP the car audio system can output stereo audio from your mobile phone The BT device of the car audio system supports AVRCP so these media buttons of the gt gt lt on remote control and gt lt lt and gt gt on control panel are available for audio video playback of your mobile phone during playback But no fast forward backward functions for the lt lt and gt gt buttons If you don t want to use the BT function of the car audio system repeatedly press SEL button to display BT then use VOL knob or VOL and VOL buttons to switch BT off 13 Disc USB card operation 1 Loading or unloading a disc USB or card 1 1 Loading a disc USB or card Label
11. eG 49 63 0 X9 9 9 OY 63 O Control Panel LITT so EDS Front side of chassis after removing control panel 1 REL button 14 lt lt button 2 PWR or MODE button 15 gt gt button 3 SEL button and VOL knob 16 PAIR or button 4 BAND or ID3 button 17 EJECT button 5 TAor AF button 18 RESET button 6 APS button 19 IR sensor window 7 MUTE or PTY button 20 AUX IN jack 8 gt or 1 button 21 USB port 9 INTor2 button 22 LCD screen 10 RPT or 3 button 23 Card slot 11 RDM or 4 button 24 CLK button 12 10 or 5 button 25 Disc slot 13 10 or 6 button 2 Locations and Names of controls remote control 1 PWR button 11 VOL button 2 lt button 12 MUTE or MODE button 3 button 13 SELor ENTER button 4 VOL button 14 gt button 5 gt or TOP or 1 button 15 button 6 RDM or 4 button 16 RPTor3 button 7 10 5 button 17 INTor2 button 8 7orTA button 18 10 button 9 DISP or button 19 9 or PTY button 10 8or AF button 20 SCAN or button 21 BAND orID30rO0 button General Operation
12. ly running is resumed AF button When you press the AF button on remote control or press the AF button on control panel itis activated as AF mode ON or OFF Segment off AF switching mode off Segment on AF switching mode on the radio continuously tests the signal strength of the AF frequency Wheneverthe new AF frequency is stronger than the station that is currently tuned in the radio switches to this frequency short time and the message NEW FREQUENCY is displayed for one to two seconds Segment flashing AF switching mode is selected but RDS information is not received yet 11 BT Operation 1 Pairing and Connecting Prior to using the BT device named BT CAR STEREO as a handfree system fora BT enabled mobile phone for the first time you must pair and connect them as follows In any mode prior to pairing and connecting the BT logo flashes in the LCD Press the PAIR button on the control panel to display PAIRING press the BAND button to cancel pairing N Switch on the BT mode of your mobile phone then select the item to find a BT device and enter it When it finds the BT device of the car audio system the name BT CAR STEREO will be displayed select it and enter it then it will show an interface that asks you to input a password input 0000 and enter it then it will pair and connect with the BT device BT CAR STEREO of the car audio system Confirm it then the BT logo will not fla
13. nally press the CLK button to confirm it MODE button To switch on a work source between RADIO DISC USB CARD AUX IN and BT AUDIO after pairing and connecting repeatedly press the MODE button on the c ontrol panel or on the remote control REL button To detach the control panel from chassis RESET button To reset all parameters to factory default values When LCD does not display normally or sound is distorted or some controls are disabled press the REL button to detach the control panel from chassis and re move the control panel from the chassis then use a subject with a sharp point end to thrush the RESET hole 9 Radio Operation BAND button To switch between F1 FM1 F2 FM2 F3 FM3 A1 AM1 and A2 AM2 lt lt amp gt gt or lt amp gt buttons In standby mode or after no manually searching operation for a while briefly press one of them to automatically search down or up for an available station and listen to it To manually search down or up for a desired station and listen to it long press one of them to enter MANUAL mode then briefly press one of them step by step SCAN button To scan for all available stations and select one of its to listen APS button To scan for every preset station of FM or AM briefly press the APS button To preset stations for every memory bank of FM or AM long press the APS button 1 6 buttons To listen to a preset station first switch on a
14. nits order of the folder SN After selecting the desired digit in units order press the SEL button to confirm To select all digits of the desired folder SN as above After selecting all digits of the desired folder SN It will display the name of the folder then press the SEL button to display FILE XXx The XXx is the minimum SN of files in the selected folder Rotate the VOL knob or press the VOL or VOL button to select the desired file SN Then it will display the selected file name press the SEL button to play the selected file 3 CHARACTER SEARCH a b Press the APS button three times to enter character search mode and display CHAR SC on LCD Press the SEL button to display and flash A then rotate the VOL knob or press the VOL or VOL button to select the first character of the desired file name Then press the SEL button to display and flash the second A Select some or all characters of the desired file name as above After selecting some or all characters of the desired file name long press the SEL button to display SEARCH and then FND XXx The XXx is the maximum SN of the files those include the selected characters Rotate the VOL knob or press the VOL or VOL button to display these files step by step D After selecting the desired file press the SEL button to play it 4 TOP button During CD MP3 WMA playback long press the TOP button to play the first track of the media INT button To swit
15. sh and light all the time When finishing pairing and connecting the audio of the mobile phone transfers to the car audio system whenever a call is made or received or the mobile phone plays music 2 BT PHONE 1 Makeacall 1 Dial with mobile phone directly 2 Dial with the controls on remote control or on control panel a Press the v button on control panel orthe button on remote control to display PHONE in the LCD b Use the number buttons to input your desired phone number When inputting a wrong digit use the BAND button on control panel or the button on remote control to delete it c After finishing inputting press the v button on control panel or the button on remote control to dial out 2 Redial last dialed phone number Pressthe button on control panel orthe button on remote control twice to dial out the last dialed phone number 212 3 4 5 lt 6 3 1 Answer a call During ringing the incoming telephone number displays in the LCD If you want to receive it press the button on control panel or press the button on remote control if you want to reject it press the button on control panel or press the button on remote control End phone talking When you want to end phone talking press the or button Switch audio between car A V system and mobile phone During phone talking using the BT handfree system of the car audio system if you wantto change th
16. t of the card slot 2 Function of buttons on main unit or remote control 1 gt button During playback use it to pause playback in pause mode use it to resume playback 2 lt lt amp gt gt lt amp gt buttons play next track briefly press gt gt or gt button To play previous track briefly press lt lt or lt button To fast backwards or forwards press and hold lt lt amp lt or gt gt amp gt button 3 APS button To quickly select a desired track to play For CD TRACK SEARCH 1 Press the APS button to enter track search mode and display TRK SCH on LCD 2 Press the SEL button to display TRK 0001 and flash the 1 The 1 is the digit of the track SN in units order Rotate the VOL knob or press the VOL or VOL button to select the digit in units order After selecting the desired digit in units order press the SEL button to confirm 3 To select all digits of the desired track SN as above 4 After selecting all digits of the desired track SN long press the SEL button to play it For MP3 WMA 1 TRACK SEARCH same as CD 15 2 DIR SEARCH a b Press APS button twice to enter dir search mode and display NAVIGAT on LCD Press the SEL button to display FOLD 001 The 1 is the digit of the folder SN in units order after a while it will display the name of the No 1 folder Then rotate the VOL knob or press the VOL or VOL button to select the digit in u
17. um Power Output 4 x 60W measured at DC 14 4 V RADIO FM Frequency 87 5MHz 107 9MHz Usable ga cece cece en ann an an an ann an an nenn anna nen 15dBu F Frequeney u een 10 7MHz AM Frequency 530KHz 1710KHz Usable Sensitivity erisiwi aranne me 40dBu F Frequency ea 450KHz CD USB card Usable audio formats CD MP3 WMA Audio teen tees 2ch amp 4ch line out Frequency 20Hz 20KHz SEE EET 90dB JIS MADE IN CHINA 88 J0916 03 19 Visit us pyleaudio com IMPORTANT Pack carefully in original package if possible We are not responsible for damage incurred in returning items for repair A letter stating your exact street address daytime phone number and the problem you are experiencing should be included You must also enclose a copy of the original receipt as proof of date of purchase Brooklyn NY 11204 718 535 1800 Monday Through Thursday 9AM to 5PM Friday 9AM to 1PM Eastern
Download Pdf Manuals
Related Search