Adtran OC-3 CWDM SFP 1471nm
Contents
1. to function without degradation during exposure to all test severities per Class 3 3 This product meets EU RoHS Directive 2002 95 EC and or appli cable exemptions Refer to www adtran com for further infor mation on RoHS WEEE ADTRAN CUSTOMER CARE From within the U S 1 800 726 8663 From outside the U S 1 256 963 8716 PRICING AND AVAILABILITY 1 800 827 0807 61442701PG1 22Ck hs CAUTION SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED2. ADRAN CLEI SITRAAFA_ _ Product P N 1442701PG1 OC 3 Small Form Factor Pluggable CWDM 1471 nm jobAid 3 Issue Date November 2010 Document P N 61442701PG1 22C DESCRIPTION The OC 3 Small Form Factor Pluggable CWDM 1471 nm SFP OC3 plugs into ADTRAN OC 3 equipment designed to accept Small Form factor Pluggables SFPs Installed into an appropriate host unit the SFP OC3 provides an OC 3 CWDM interface to the supporting system NOTE To ensure compatibility refer to the documentation provided with the host module The following features are supported on the SFP OC3 SONET OC 3 compatible 155 52 Mb s 1471 nm long reach single mode 2 fiber operation 80 km maximum optical span Due to compliance certification requirements use only SFPs supplied by ADTRAN with the host module ADTRAN cannot certify system integrity with other SFPs SPECIFICATIONS Optical Specifications Optical transmit level 0 dBm to 5 dBm Optical receive level 10 dBm to 34 dBm Power penalty 1 dB Optical budget 28 1 dBm Minimum span attenuation 10 dB Optical connectors LC Extended Environmental Support Operational temperature range 40 C to 65 C Storage temperature range 40 C to 85 C Relative humidity to 95 noncondensing INSTALLATION To install the SFP OC3 into an appropriate module complete the following steps 1 Inspect the SFP OC3 If damaged file a claim with the
3. car rier and then contact ADTRAN Customer Support Do not remove the protective end cap from the SFP until the fiber optic cable is ready to be connected 2 Insert the SFP OC3 into the SFP cage on the module Ensure that the manufacturer s label on the SFP is facing upward for correct installation 3 Slide the SFP OC3 all the way into the receptacle until there is an audible click NOTE The latch on the SFP is used to remove the SFP from the cage on the circuit card PROVISIONING The SFP OC3 is not directly provisionable To provision the SFP OC3 access the menu system of the host module Refer to the Provisioning section of the Job Aid or I amp M provided with the host module for provisioning details SAFETY AND REGULATORY COMPLIANCE Electrostatic Discharge ESD can damage electronic modules When handling modules wear an antistatic discharge wrist strap to prevent damage to electronic components Place modules in antistatic packing material when transporting or storing When working on modules always place them on an approved antistatic mat that is electrically grounded The SFP OC3 is NRTL Listed to the applicable UL standards The SFP OC3 meets or exceeds all the applicable requirements of NEBS Telcordia GR 63 CORE GR 1089 CORE and ETSI EN 300368 The SFP OC3 is intended for deployment in Central Office type facilities EEEs EECs and locations where the NEC applies for example Customer Premise
4. nsure that the metal enclosure of the SFP OC3 is properly grounded via the backplane connector NOTE The OC 3 port s are optical and therefore are not classified as any type of port as defined in Appendix B of GR 1089 CORE Issue 5 This SFP OC3 is compliant with SFF 8472 Digital Diagnostics Monitoring Interface for Optical Transceivers Revision 9 3 This SFP OC3 is compliant with the Small Form Factor Pluggable SFP Multi Source Agreement MSA This product is designed to be deployed in GR 3108 CORE environment class 1 or 2 as defined in GR 3108 CORE issue 2 The SFP OC3 is designed to meet the following environmental classes ETSI EN 300 019 1 1 Classification of environmental conditions Storage Class 1 2 ETSI EN 300 019 1 2 Classification of environmental conditions Transportation Class 2 3 Warranty ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service Warranty information can be found online at www adtran com warranty 2010 ADTRAN Inc All Rights Reserved ETSI EN 300 019 1 3 Classification of environmental conditions Stationary use at weather protected locations Class 3 3 ETSI EN 300 386 Electromagnetic compatibility and Radio spectrum Matters ERM Telecommunication network equipment Electromagnetic Compatibility EMC requirements The equipment is designed
5. s The SFP OC3 is to be installed in ADTRAN products in Restricted Access Locations only and installed by trained service personnel ADRAN This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by ADTRAN could void the user s authority to operate this equipment The SFP OC3 contains a Class 1 laser that complies with the Laser Safety requirements of FDA 21 CFR 1040 10 and 1040 11 and EN 60825 1 and 2 The SFP OC3 is NRTL Listed and CB Certified to all applicable American and European safety standards Per GR 1089 CORE Section 9 the SFP OC3 does not have an internal DC connection between battery return and frame ground The ADTRAN system that the SFP OC3 is being deployed in is designed and intended for installation as part of a Common Bonding Network CBN or Isolated Bonding network IBN The SFP OC3 can be installed in a DC I isolated or DC C common configuration For installations where other cards or the host system have internal connections between battery return and frame ground the system would be intended for deployment only in a DC C configuration The ADTRAN system chassis frame ground terminal must be connected to a reliable earth ground to e
Download Pdf Manuals
Related Search