Adtran SFP 1490/1310nm 10km
Contents
1. DESCRIPTION The Small Form Factor Pluggable SFP Gigabit Ethernet Single Fiber is a bidirectional SFP that installs into the Optical Loop Termination OLT designed to accept SFPs The SFP provides a single optical interface to the GigE physical interface Installed into an appropriate OLT the SFP provides a Gigabit Ethernet interface to the supporting system NOTE To ensure compatibility refer to the documentation provided with the OLT In a deployment consisting of an OLT with a 1442110G1 SFP installed the Optical Network Unit ONU should have a complementary 1442110G2 SFP installed The following features are supported on the SFP 1000Base LX 1490 nm Transmitter 1000Base LX 1310 nm Receiver Optical distance 10 km maximum Due to compliance certification requirements only SFPs supplied by ADTRAN should be used ADTRAN cannot certify system integrity with other SFPs OLT 1442110G1 1442110G2 ONU Rx 1310 nm Tx 1490 nm Rx 1490 nm Tx 1310 nm Small Form Factor Pluggable 1490 nm TX 1310 nm RX 10 km Operational Specifications Optical Specifications Transmit wavelength 1490 nm Receive wavelength 1310 nm Optical transmit level 9 dBm to 3 dBm Optical receive level 19 5 dBm to 3 dBm Optical distance 10 km Optical connectors LC Extended Environmental Support Operational temperature range 40 C to 85 C Storag2. e temperature range 40 C to 85 C Relative humidity to 95 noncondensing INSTALLATION Prior to installation inspect the SFP If damage has occured during shipping file a claim with the carrier and then contact ADTRAN Customer Support For more information refer to Warranty To install the SFP into an appropriate module complete the following steps 1 Insert the SFP into the SFP cage on the circuit board of the host module with the latch handle facing outward Slide the SFP all the way into the cage NOTE The latch on the SFP is for removal only When removing the SFP rotate the latch away from the SFP the SFP should slide easily out of the cage 2 Exert adequate pressure to ensure the SFP is completely seated in the SFP cage 3 Do not remove the connector plug until the optical fiber connection is made It is recommended that the connector plug remain on whenever the transciever optical fiber connector is not inserted 4 Continue the installation and turn up of the host module using the instructions in the Job Aid provided with the module or using the Installation and Maintenance Practice I amp M available online at www adtran com CLEI BVL3ADJD_ _ Product P N 1442110G1 Issue Date 0812 Document P N 61442110G1 22A C A U T I O N C A U T I O N SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED Warranty ADTRAN will replace or repair t
3. his product within the warranty period if it does not meet its published specifications or fails while in service Warranty information can be found online at www adtran com warranty 2008 ADTRAN Inc All Rights Reserved PRICING AND AVAILABILITY 800 827 0807 TECHNICAL SUPPORT 800 726 8663 RETURN FOR REPAIR 256 963 8722 61442110G1 22A COMPLIANCE Electrostatic Discharge ESD can damage electronic modules When handling modules wear an antistatic discharge wrist strap to prevent damage to electronic components Place modules in antistatic packing material when transporting or storing When working on modules always place them on an approved antistatic mat that is electrically grounded The SFP is NRTL Listed to the applicable UL standards The SFP meets or exceeds all the appli cable requirements of NEBS Telcordia GR 63 CORE and GR 1089 CORE The SFP is intended for deployment in Central Office type facilities EEEs EECs and locations where the NEC applies for example Customer Premises and is intended to be installed by trained service personnel Install the SFP in an ADTRAN product located in a restricted access location This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modificat
4. ions not expressly approved by ADTRAN could void the user s authority to operate this equipment Per GR 1089 CORE the ADTRAN system that the SFP is being deployed in is designed and intended for installation as part of a Common Bonding Network CBN The ADTRAN system that the SFP is being deployed in is not designed nor intended for installation as part of an Isolated Bonding Network IBN Per GR 1089 CORE Section 9 the SFP does not have an internal DC connection between battery return and frame ground The SFP can be installed in a DC I isolated or DC C common installation For installations where other cards or the host system have internal connections between battery return and frame ground the system would be intended for deployment only in a DC C installation The ADTRAN system chassis frame ground terminal must be connected to an earth ground to ensure that the metal enclosure of the SFP is properly grounded via the backplane connector NOTE The Gigabit Ethernet port s are optical and therefore are not classified as any type of port as defined in Appendix B of GR 1089 CORE Issue 4 The SFP is designed to meet the following environ mental classes ETSI EN 300 019 1 1 Classification of environmental conditions Storage Class 1 2 ETSI EN 300 019 1 2 Classification of environmental conditions Transportation Class 2 3 ETSI EN 300 019 1 3 Classification of environmental co
5. nditions Stationary use at weather protected locations Class 3 3 The equipment is designed to function without degra dation during exposure to all test severities per Class 3 3
Download Pdf Manuals
Related Search