Cisco SATA SFF (STEC)
Contents
1. Table 15 Rail Kit Product ID PID PID Description R2XX G31032RAIL Rail Kit for UCS 200 210 Rack Servers NOTE This third generation rail kit works in racks with square holes or 10 32 round holes and is shorter than the previous generation rail kit The new R2XX G31032RAIL measures 23 5 inches to 36 Inches in length By comparison the previous version R250 SLDRAIL measured 27 inches to 37 inches in length o9 See the section titled OPTIONAL STEP ORDER RACK s on page 44 for information about racks and rack equipment Cisco UCS C210 M2 General Purpose Rack Mount Server 33 CONFIGURING the SERVER STEP 13 ORDER OPTIONAL CABLE MANAGEMENT ARM The cable management arm hooks onto the right and left slide rails at the rear of the server and is used for cable management You can order the cable management arm listed in Table 16 Table 16 Cable Management Arm Product ID PID PID Description R2XX CMAG3 1032 Cable Mgmt Arm for R2XX G31032RAIL for C200 C210 For more information about the cable management arm see the Cisco UCS C210 Installation and Service Guide at this URL http www cisco com en US docs unified_computing ucs c hw C210M1 install C210M1 html 34 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 14 ORDER A TRUSTED PLATFORM MODULE Trusted Platform Module TPM is a computer chip microcontroller that can securely store artifacts used to authenticate the2. 3 memory channels per CPU up to 2 DIMMs per channel mmm Bank 1 mm Bank 2 Cisco UCS C210 M2 General Purpose Rack Mount Server 13 CONFIGURING the SERVER Choose DIMMs and Memory Mirroring Choose the memory configuration and whether or not you want the memory mirroring option The available memory DIMMs and mirroring option are listed in Table 5 o NOTE When memory mirroring is enabled the memory subsystem simultaneously writes identical data to two channels If a memory read from one of the channels returns incorrect data due to an uncorrectable memory error the system automatically retrieves the data from the other channel A transient or soft error in one channel does not affect the mirrored data and operation continues unless there iS a simultaneous error in exactly the same location on a DIMM and its mirrored DIMM Memory mirroring reduces the amount of memory available to the operating system by 50 because only one of the two populated channels provides data Table 5 Available DDR3 DIMMs Product ID PID PID Description Voltage iim DIMM Options UCS MR 1X041RX A 4GB DDR3 1333 MHz RDIMM PC3 10600 1R 1 35v 1 35 1 UCS MR 1X082RX A 8GB DDR3 1333 MHz RDIMM PC3 10600 2R 1 35v 1 35 2 UCS MR 1X162RY A 16GB DDR3 1600 MHz RDIMM PC3 12800 2R x4 1 5v 1 35 1 5V 4 Memory Mirroring Option NO1 MMIRROR Memory mirroring option Approved Configurations 1 1 CPU configuration without memory mirroring
3. The Cisco UCS C210 M2 server is a general purpose two socket two rack unit 2RU rack server that builds on the success of the UCS C210 M1 server The UCS C210 M2 server shown in Figure 1 extends the capabilities of the Cisco Unified Computing System The server uses Intel s latest Xeon 5600 Series multicore processors with 12 DIMM slots 5 PCle slots embedded dual port gigabit Ethernet controller and up to 16 2 5 inch SAS SATA hot swappable hard disk drives HDDs or solid state drives SSDs Figure 1 Cisco UCS C210 M2 High Density Rack Server Front View efefet T stesse 9495 599999 s o 92 5 5 5 5 5 i eo t ms E Rear View eS z r r K A U EEH j 0 0 0 0 0 j635953 3s352 3 92 4 0 0 0 8 Ed 33 wh wd BOR BEE Cisco UCS C210 M2 General Purpose Rack Mount Server DETAILED VIEWS DETAILED VIEWS Chassis Front View Figure 2 shows the Cisco UCS C210 M2 General Purpose Rack Server Figure 2 Chassis Front View n Y LL LX IE LX bs do LRE L dy IEKE dennen ren Mpegs 4D eee BD A ee ed ee i PL oJ oe JE AJ nrd rrd ee eee E d 3 Ip g men a ea ee ad EAE ixi re id La mI iur un d r Bm CT jen ee ele OL A TI n wak Bl ol 4 ase x5 4 ib xx Nes ee Hnn Hnn e EErEE zzzzzz SEEN i es oy I XT DOO el o DEAE lo nx ele By fit n DD as DO DD i TRT PER Emp ey
4. UCS SSD100GI1F104 NEW 100GB SATA SSD SFF STEC SATA 100 GB Cisco UCS C210 M2 General Purpose Rack Mount Server 21 CONFIGURING the SERVER Approved Configurations 1 Integrated SATA RAID 0 1 controller m Select up to 4 SATA only drives listed in Table 8 You cannot mix HDD and SDD SATA drive types 2 LSI 1064E 4 port SAS 6 0G RAID Mezzanine card RAID controller m Select up to four SAS or SATA drives listed in Table 8 You cannot mix HDD and SSD drives You cannot mix SAS and SATA drive types 3 LSI MegaRAID SAS 9280 4i4e RAID controller m Select up to four SAS or SATA internal drives listed in Table 8 for configurations with the factory default extender You cannot mix HDD and SSD drive types or SAS and SATA drives 4 LSI MegaRAID SAS 9261 8i RAID controller m Select up to eight internal SAS or SATA drives listed in Table 8 You can mix SAS and SATA drives but you cannot mix HDD and SSD drive types If you order the optional SAS Expander the controller can support up to 16 internal drives Caveats B If the integrated RAID controller on the server motherboard is used no PCle or mezzanine card controller selected all the drives must be SATA A SAS Extender is not field upgradable to a SAS Expander so if you are configuring a system with eight or more drives or anticipate the system will implement more than eight drives in the future make sure you order a SAS Expander You can replace an extender or expander o
5. AC power cord 27 p Cn d s o 250V SFS 250V 10A AR Power Cord SFS 250V 10A Argentina i ee n peu rating 10 2 mia SAIS Connector IECGO320 C13 5 CAB 9K10A AU Power Cord 250VAC 10A 3112 Plug Australia Spo va UT d Lf _ Wp KE Cordset rating 10 A 250 V 500 V MAX 7 SN AEN Length 2500mm M 0 Connector EL 701C EN 60320 C15 g BS sea d AME fuse 30 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER Table 14 Available Power Cords continued Product ID PID SFS 250V 10A CN CAB 9K10A EU SFS 250V 10A ID SFS 250V 10A IS CAB 9K10A IT CAB 9K10A SW CAB 9K10A UK PID Description Power Cord SFS 250V 10A China Power Cord 250VAC 10A CEE 7 7 Plug EU Power Cord SFS 250V 104A India Power Cord SFS 250V 10A Israel Power Cord 250VAC 10A CEI 23 16 VII Plug Italy Power Cord 250VAC 10A MP232 Plug Switzerland Power Cord 250VAC 10A BS1363 Plug 13 A fuse UK Cisco UCS C210 M2 General Purpose Rack Mount Server Images 0 9 i o Fu Plug EL 218 CCEE GB2009 Plug EL 208 3G CEI 23 16 Plug Plug MP232 R Z e Eh 3 6 mg Cordset lene a 16A 250V 2500mm mmy Cordset rating 10A 2
6. This service provides expert software and hardware support to help sustain performance and high availability of the unified computing environment Access to Cisco Technical Assistance Center TAC is provided around the clock from anywhere in the world For UCS blade servers there is Smart Call Home which provides proactive embedded diagnostics and real time alerts For systems that include Unified Computing System Manager the support service includes downloads of UCSM upgrades The Unified Computing Support Service includes flexible hardware replacement options including replacement in as little as two hours There is also access to Cisco s extensive online technical resources to help maintain Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER optimal efficiency and uptime of the unified computing environment You can choose a desired service listed in Table 22 Table 22 UCS Computing Support Service Product ID PID On Site Description CON UCS1 R210W No UC Support 8X5XNBD CON UCS2 R210W No UC Support 8X5X4 CON UCS3 R210W No UC Support 24x7x4 CON UCS4 R210W No UC Support 24x7x2 CON UCS5 R210W Yes UC Support 8X5XNBD CON UCS6 R210W Yes UC Support 8X5X4 CON UCS7 R210W Yes UC Support 24x7x4 CON UCS8 R210W Yes UC Support 24x7x2 Unified Computing Warranty Plus Service For faster parts replacement than is provided with the standard Cisco Unified Computing System warranty Cisco offers the Cisco Uni
7. 1Yr Svcs Required RHEL 2 Socket 1 Guest 3Yr Svcs Required RHEL 2 Socket 4 Guest 1Yr Svcs Required RHEL 2 Socket 4 Guest 3Yr Svcs Required RHEL 2 Socket U Guest 1Yr Svcs Required RHEL 2 Socket U Guest 3Yr Svcs Required RHEL 2 Socket 1 Guest 1Yr Subscription Redhat Svcs Included RHEL 2 Socket 1 Guest 3Yr Subscription Redhat Svcs Included RHEL 2 Socket 2 Guest 3Yr Subscription Redhat Svcs Included RHEL 2 Socket 4 Guest 1Yr Subscription Redhat Svcs Included RHEL 2 Socket U Guest 1Yr Subscription Redhat Svcs Included RHEL 2 Socket U Guest 3Yr Subscription Redhat Svcs Included RHEL Option High Availability 2 Socket 1Yr Svcs Required RHEL Option Resilient w Ha 2 Socket 1 Yr Svcs Required RHEL Option Scalable File System 2 Socket 1 Yr Svcs Required RHEL Option High Availability 2 Socket 3Yr Svcs Required RHEL Option Resilient Storage w HA 2 Socket 3 Yr Svcs Reqd RHEL Option Scalable File System 2 Socket 3 Yr Svcs Required RHEL Option High Availability 2 Socket 1Yr Redhat Svcs Incld RHEL Option Resilient Storage 2 Socket 1 Yr Redhat Svcs Incl Cisco UCS C210 M2 General Purpose Rack Mount Server Table 18 CONFIGURING the SERVER Operating Systems continued PID Description RHEL SFS 2S 1A RS RHEL HA 2S 3A RS RHEL RS 2S 3A RS RHEL SFS 2S 3A RS Windows Server MSWS 08 STHV MSWS 08 ENHV MSWS 08R2 STHV MSWS 08R2 ENHV MSWS 08R2 DCHV2S MSWS 08R2 DCHV4S VMWare Server VMW VS A
8. 24x7x2 UCWD5 8x5xNBD Onsite UCWD6 8x5x4 Onsite UCWD7 24x7x4 Onsite UCWD8 24x7x2 Onsite For more service and support information see the following URL Product ID PID CON UCWD2 R210WSFF CON UCWD3 R210WSFF CON UCWD4 R210WSFF CON UCWD5 R210WSFF CON UCWD6 R210WSFF CON UCWD7 R210WSFF CON UCWD8 R210WSFF http www cisco com en US services ps2961 ps10312 ps10321 Cisco UC Warranty Support DS pdf For a complete listing of available services for Cisco Unified Computing System see this URL http www cisco com en US products ps10312 serv group home html Cisco UCS C210 M2 General Purpose Rack Mount Server 43 OPTIONAL STEP ORDER RACK s OPTIONAL STEP ORDER RACK s The optional R42610 rack is available from Cisco for the C Series servers including the C210 M2 server This rack is a standard 19 inch rack and can be ordered with a variety of options as listed in Table 25 Racks are shipped separately from the C210 M2 server Table 25 Racks and Rack Options Product ID PID PID Description RACK UCS Cisco R42610 expansion rack no side panels RACK UCS2 Cisco R42610 standard rack w side panels RACK BLANK 001 Filler panels qty 12 1U plastic toolless RACK CBLMGT 001 Cable mgt D rings qty 10 metal RACK CBLMGT 011 Cable mgt straps qty 10 Velcro RACK FASTEN 001 Mounting screws qty 100 M6 RACK FASTEN 002 Cage nuts qty 50 M6 RACK J OIN 001 Rack joining kit Notes 1 Use these same base PIDs t
9. BIOS drivers and firmware updates UCSM updates for systems with Unified Computing System Manager These updates include minor enhancements and bug fixes that are designed to maintain the compliance of UCSM with published specifications release notes and industry standards Unified Computing Mission Critical Service This service delivers personalized technical account management expedited technical support and expert field support engineering for the Cisco Unified Computing System UCS The Mission Critical Support Service provides a designated technical account manager TAM who acts as a strategic resource to help ensure that the unified computing environment runs at peak efficiency If a problem arises that threatens business continuity the TAM provides crisis management leadership and your IT staff receives expedited access to Cisco s Technical Assistance Center TAC Please note This service has qualification criteria Your company must have 1 2M of UCS equipment 200 blades and a single location to qualify for this service level Choose the desired service listed in Table 21 Table 21 Unified Computing Mission Critical Service Product ID PID On Site Description CON UCM7 R210W Yes UC Mission Critical 24x7x4 On site CON UCM8 R210W Yes UC Mission Critical 24x7x2 On site Unified Computing Support Service For support of the entire Unified Computing System Cisco offers the Cisco Unified Computing Support Service
10. DIMM slots Al B1 and C1 belong to Bank 1 while A2 B2 and C2 belong to Bank 2 Figure 7 shows how banks and channels are physically laid out on the motherboard The DIMM slots on the right channels A B and C are associated with CPU1 while the DIMM slots on the left channels D E and F are associated with CPU2 The Bank 1 blue DIMM slots are always located farther away from a CPU than the corresponding Bank 2 black slots Bank 1 slots are populated before Bank 2 slots If only one DIMM is used for CPU 1 for example it must be located in slot 2 A1 channel A bank 1 likewise if only one DIMM is used for CPU 2 it must be installed in slot 2 D1 channel D bank 1 Figure 7 CPU DIMM Channels and Banks C210 M2 Server Back Slot 4 Slot 3 Slot 2 Slot 1 Slot 1 Slot 2 Slot 3 Slot 4 WO Lu H o u LM Slot 5 Slot 6 F1 F2 E1 E2 D1 D2 A2 Al B2 B1 C2 C1 DIMM Module mmm Bank 1 Sockets blue Gam Bank 2 Sockets black Cisco UCS C210 M2 General Purpose Rack Mount Server 47 SUPPLEMENTAL MATERIAL Memory Population Rules When considering the memory configuration of your server you should consider the following items DIMMs within the server should all be the same type and speed If you mix different DIMM types or DIMMs with different clock rates in the same server such configurations are supported however these configurations may cause the system to operate at less than optimum levels
11. e LSI 6G MegaRAID SAS 9280 4i4e controller RAID levels 0 1 5 6 10 50 or 60 support for up to 4 internal SAS or SATA drives no mixing with the factory default SAS Extender plus external J BOD expansion or e LSI 6G MegaRAID SAS 9261 8i controller RAID levels 0 1 5 6 10 50 or 60 support for up to 8 internal SAS or SATA drives with the factory default SAS Extender or up to 16 SAS or SATA drives with a SAS Expander installed m 1280 x 1024 resolution B 32 bit color depth m 8 MB video memory m Upto 16 2 5 inch SAS or SATA hot swappable hard disk drives HDDs or solid state drives SSDs m USB socket on motherboard Cisco UCS C210 M2 General Purpose Rack Mount Server BASE SERVER STANDARD CAPABILITIES and FEATURES Capability Feature Description Interfaces m Rear panel e One DB9 serial port connector e Two USB 2 0 port connectors e One DB15 VGA connector e Two RJ 45 10 100 1000 Ethernet port connectors e One RJ 45 10 100 Ethernet management port m Front panel e One KVM console connector Front Panel m Optional DVD RW optical drive with dual layer DL media support Power subsystem Up to two 650 W power supplies NHL or nonredundant configuration options Fans Chassis B Three 80 mm redundant fans Power supply m Each power supply is equipped with a fan Integrated management Cisco Integrated Management Controller CIMC with integrated video KVM processor redirection Security Intelligence Ope
12. platform server These artifacts can include passwords certificates or encryption keys A TPM can also be used to store platform measurements that help ensure that the platform remains trustworthy Authentication ensuring that the platform can prove that it is what it claims to be and attestation a process helping to prove that a platform is trustworthy and has not been breached are necessary steps to ensure safer computing in all environments The TPM ordering information is listed in Table 17 Table 17 Trusted Platform Module Product ID PID PID Description R200 TPM1 Trusted Platform Module Cisco UCS C210 M2 General Purpose Rack Mount Server 35 CONFIGURING the SERVER 36 STEP 15 CHOOSE OPERATING SYSTEM Several operating systems are available from which to choose Choose one of the operating systems listed in Table 18 Table 18 Operating Systems PID Description Product ID PID SUSE Linux Enterprise Server SLES 1A SLES 3A SLES lyr subscription svcs required 0 media SLES 3yr subscription svcs required 0 media Red Hat Enterprise Linux RHEL 2S 1G 1A RHEL 2S 1G 3A RHEL 2S 4G 1A RHEL 2S 4G 3A RHEL 2S UG 1A RHEL 2S UG 3A RHEL 2S 1G 1A RS RHEL 2S 1G 3A RS RHEL 2S 4G 3A RS RHEL 2S 4G 1A RS RHEL 2S UG 1A RS RHEL 2S UG 3A RS RHEL Add Ons RHEL HA 2S 1A RHEL RS 2S 1A RHEL SFS 2S 1A RHEL HA 2S 3A RHEL RS 2S 3A RHEL SFS 2S 3A RHEL HA 2S 1A RS RHEL RS 2S 1A RS RHEL 2 Socket 1 Guest
13. 10 M2 General Purpose Rack Mount Server 23 CONFIGURING the SERVER Approved Configurations 1 No RAID controller plug in card B f you did not choose a plug in RAID controller for example you are using the mezzanine card or the interated RAID controller on the motherboard you can select up to five PCle option cards listed in Table 9 2 One RAID controller plug in card B f you selected a plug in RAID controller you can select up to four of the optional PCle cards listed in Table 9 NOTE If a plug in RAID controller card is installed any optional PCle card you select will be installed in one of the remaining four PCle slots You can install a maximum of one plug in PCle RAID controller card Caveats m There are five PCle slots All are full height All of the PCle adapter cards are half height with the exception of the Virtual Interface Card VIC N2XX ACPCIO1 which is a full height card If you selected a plug in RAID controller in STEP 4 CHOOSE RAID CONFIGURATION four slots remain available Only a single Cisco UCS P81E Virtual Interface Card 2 port 10Gbp card may be installed and it must be installed in slot 1 or slot 2 Note however that if the server is running UCSM only slot 1 is supported for the VIC card See Figure 3 on page 5 for slot numbering e NOTE If you are using Unified Computing System Manager UCSM the Cisco UCS NI P81E Virtual Interface Card 2 port 10Gbp card must be i
14. 263 W m 50 Load Power 419 W m Max Power 5 4W 60 Cisco UCS C210 M2 General Purpose Rack Mount Server TECHNICAL SPECIFICATIONS Environmental Specifications The power specifications for the C210 M2 server are listed in Table 32 Table 32 UCS C210 M2 Environmental Specifications Parameter Minimum Temperature operating Temperature nonoperating Altitude operating Humidity nonoperating Vibration nonoperating Shock operating Shock nonoperating Electrostatic discharge Acoustic 10 C to 35 C 50 F to 95 F 40 C to 65 C 40 F to 149 F 0 to 3 000 m 0 to 10 000 ft maximum ambient temperature decreases by 1 per 300 m 5 to 93 noncondensing 2 2 Grms 10 minutes per axis on each of the three axes Half sine 2 G 11 ms pulse 100 pulses in each direction on each of the three axes Trapezoidal 25 G two drops on each of six faces Velocity 2175 inches per second on bottom face drop Velocity 290 inches per second on the other five faces Tested to ESD levels up to 15 kilovolts kV air discharge and up to 8 kV contact discharge without physical damage Sound power 54 7 dBA 5 7 Bels at ambient temperature 23 C measured using the Dome Method GOST MsanPiN 001 96 Cisco UCS C210 M2 General Purpose Rack Mount Server 61 TECHNICAL SPECIFICATIONS Compliance Requirements The regulatory compliance requirements for C Series servers are listed in Table 33 Table 33 UCS C Series Regu
15. 50V 2500 mm Connector EL 701 e IEC60320 C13 BTL rating 10A 16 A 250 V piu 8 ft 2 in 2 5 m Cordset rating 10A 250V 500V MAX 2500 mm JE Connector IEC60320 C13 ror IH Manann ETTEN i Cordset rating 10 A 250 V Length 8 ft 2 in 2 5 m Connector C15M EN60320 C15 m 77 c E Cordset rating 10 A 250 V Length 8 ft 2 in 2 5 m Connector IEC 60320 C15 Z RA Jj 1 LA TS T id we fuse Cordset rating 10 A 250 V 500 V MAX 7 S Length 2500mm ER Connector EL 701C EN 60320 C15 s 31 32 CONFIGURING the SERVER Table 14 Available Power Cords continued Product ID PID PID Description Images CAB 9K12A NA Power Cord 125VAC 13A NEMA Image not available 5 15 Plug North America CAB PN 3PIN Power Cord 3PIN J apan Image not available Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 12 ORDER TOOL LESS OPTIONAL RAIL KIT A rail kit is not included with the Cisco UCS C210 M2 base server chassis but you can order the tool less rail kit listed in Table 15
16. Ahali i CISCO This product has been Spec Sheet discontinued Cisco UCS C210 M2 General Purpose Rack Mount Server Cisco SYSTEMS PUBLICATION HISTORY 170 WEST TASMAN DR SAN J OSE CA 95134 REVA 10 August 22 2012 WWW CISCO COM CONTENTS OVERVIEW Gee oa ENDED EES CEA E ECHO Y SX SVO ee DETAILED VIEWS es Chassis Front VIEW vua xod dede Ex dedo dew 09 RHA Ea EERAELEE FEA e Chassis Rear View eh ho hh n nns BASE SERVER STANDARD CAPABILITIES and FEATURES e CONFIGURING the SERVER s eee eee eee eee ees STEP 1 VERIFY BASE SU s a acu aide uas ow aen ee bo X OR eee We weak ee oa Step 2 CHOOSE CPUS 2c 26444085 e 29 99 eh See et ea aru eee ee eae er 3 SIEP BS CHOOSE MEMORY ta edward HUE ee 3 EENET OE DE ERE dei dE RE STEP 4 CHOOSE RAID CONFIGURATION RR RR STEP 5 ORDER SAS EXPANDER AS NEEDED Ree STEP 6 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES 0006 STEP 7 CHOOSE PCle OPTION CARD S le STEP 8 ORDER OPTIONAL NETWORK CARD ACCESSORIES llle STEP 9 CHOOSE OPTIONAL DVD RW DRIVE sasaaa aaa STEP 10 ORDER OPTIONAL REDUNDANT POWER SUPPLY 0 00000 es STEP 11 CHOOSE AC POWER CORDS ce ees STEP 12 ORDER TOOL LESS OPTIONAL RAIL KIT lee ee STEP 13 ORDER OPTIONAL CABLE MANAGEMENT ARM eeuee STEP 14 ORDER A TRUSTED PLATFORM MODULE 0 0 0 eee eee STEP 15 CHOOSE OPERATING SYSTEM ic444 4 chad
17. B Choose from one to six DIMMs note that there are six DIMM slots per CPU 2 1 CPU configuration with memory mirroring B Choose either two or four DIMMs The DIMMs will be placed by the factory as shown in the following table Number of DIMM Placement in Channels DIMMs Channel C is not used with memory mirroring 2 DIMM in Channel A 1 DIMM in Channel B 4 2 DIMMs in Channel A 2 DIMMs in Channel B B Choose the memory mirroring option NO1 MMIRROR as shown in Table 5 on page 14 14 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER 3 2 CPU configuration without memory mirroring m Choose from 1 to 6 DIMMs per CPU from 2 to 12 total DIMMs 4 2 CPU configuration with memory mirroring m Choose 2 4 6 or 8 DIMMs per CPU The DIMMs will be placed by the factory as shown in the following table Number of DIMM Placement DIMMs Channels C and F are not used with memory mirroring 2 CPU 1 1 DIMM in Channel A CPU 2 1 DIMM in Channel D 4 CPU 1 2 DIMMs in Channel A CPU 2 2 DIMMs in Channel D 6 CPU 1 CPU 2 2 DIMMs in Channel A 2 DIMMs in Channel D 1 DIMM in Channel B 1 DIMM in Channel E 8 CPU 1 CPU 2 2 DIMMs in Channel A 2 DIMMs in Channel D 2 DIMMs in Channel B 2 DIMMs in Channel E B Choose the memory mirroring option NO1 MMIRROR as shown in Table 5 on page 14 O NOTE System performance is optimized when the DIMM memory type and the DIMM quantity is equal for both CPUs Cave
18. C210 M2 General Purpose Rack Mount Server SUPPLEMENTAL MATERIAL PDUs Cisco RP Series Power Distribution Units PDUs offer power distribution with branch circuit protection Cisco RP Series PDU models distribute power to up to 24 outlets The architecture organizes power distribution simplifies cable management and enables you to move add and change rack equipment without an electrician With a Cisco RP Series PDU in the rack you can replace up to two dozen input power cords with just one The fixed input cord connects to the power source from overhead or under floor distribution Your IT equipment is then powered by PDU outlets in the rack using short easy to manage power cords The C series severs accept the zero rack unit ORU PDU See Figure 13 Figure 13 Zero Rack Unit PDU PID RP208 30 2P U 2 Breakers C19 plugs EG Cisco RP Series PDU models provide two 20 ampere A circuit breakers for groups of receptacles The effects of a tripped circuit are limited to a receptacle group Simply press a button to reset that circuit Cisco UCS C210 M2 General Purpose Rack Mount Server 55 56 SUPPLEMENTAL MATERIAL POWER SUPPLIES The C210 M2 can accommodate one or two 650 W power supplies A typical power supply is shown in Figure 14 Figure 14 C210 M2 Power Supply Cisco UCS C210 M2 General Purpose Rack Mount Server SUPPLEMENTAL MATERIAL KVM CABLE The KVM cable provides a connection into the ser
19. CAPABILITIES and FEATURES BASE SERVER STANDARD CAPABILITIES and FEATURES Table 1 lists the capabilities and features of the base server Details about how to configure the server for a particular feature or capability for example number of processors disk drives or amount of memory are provided in CONFIGURING the SERVER on page 8 Table 1 Capabilities and Features Capability Feature Chassis CPU Chipset Memory NIC Expansion slots Storage controller Video Internal storage devices Description Two rack unit 2RU chassis Up to two quad core Intel Xeon 5500 or 5600 series processors Intel 5520 Tylersburg chipset 12 slots for registered ECC DIMMS up to 192 GB supporting Intel SDDC Embedded dual port Intel 82576NS PCle based Gigabit Ethernet controller Five PCle slots on a riser card m Slots 1 and 4 are full height full length x8 lane with a x16 connector B Slots 2 3 and 5 are full height half length x8 lane with a x16 connector One of the following m An onboard SATA RAID 0 1 controller integrated on motherboard Intel ICH10R that can control up to four SATA drives only or m An optional RAID mezzanine card e SI amp 1064E 4 port controller mezzanine card RAID levels 0 1 or 1E for up to 4 internal SAS or SATA drives with the factory default SAS Extender or the optional SAS Expander installed or m One of these optional RAID PCle plug in cards installed in PCle slot 4
20. CS C210 M2 General Purpose Rack Mount Server 51 SUPPLEMENTAL MATERIAL SAS EXTENDER and SAS EXPANDER This server has two factory configurable options for the hard drive backplane connection m Standard SAS extender or B Optional SAS expander SAS Extender The SAS extender see Figure 10 is installed by default in the C210 M2 server Figure 10 SAS Extender 197658 The extender implements four mini SAS SFF 8087 cable connectors each of which provides a connection for up to four drives The extender supports connection for up to four drives when using the onboard RAID controller the LSI 1064E mezzanine card or the LSI MegaRAID SAS 9280 4i4e and up to 8 drives when using the LSI MegaRAID SAS 9261 81 MegaRAID card NOTE The SAS extender is field replaceable but you cannot upgrade from a SAS extender to a SAS expander in the field due to cable routing constraints You can WS replace an extender or expander only with the same type of card SAS Expander The SAS expander see Figure 11 may be optionally ordered for the C210 M2 server Figure 11 SAS Expander 19 659 O NOTE The SAS expander is a factory configurable option in this server The expander is field replaceable The SAS Expander has two mini SAS SFF 8087 cable connectors One connector provides connection for up to 16 drives and the second connector provides redundancy 52 Cisco UCS C210 M2 General Purpose Rack Mount Server S
21. DV 1A VMW VS ADV 3A VMW VS ENT 1A VMW VS ENT 3A VMW VS ENTP 1A VMW VS ENTP 3A VMW VCS 1A VMW VCS 3A Product ID PID RHEL Option Scalable File Sys 2 Socket 1 Yr Redhat Svcs Incl RHEL Option High Availability 2 Socket 3Yr Redhat Svcs Incld RHEL Option Resilient Storage 2 Socket 3 Yr Redhat Svcs Incl RHEL Option Scalable File Sys 2 Socket 3 Yr Redhat Svcs Incl Windows Svr 2008 ST media 1 4CPU 5CAL Windows Svr 2008 EN media 1 8CPU 25CAL Windows Svr 2008 ST media R2 ST 1 4CPU 5CAL Windows Svr 2008 EN media R2 EN 1 8CPU 25CAL Windows Svr 2008 R2 2 CPU Data Center Windows Svr 2008 R2 4 CPU Data Center VMware vSphere Advanced 1 CPU lyr 24x7 support VMware vSphere Advanced 1 CPU 3yr 24x7 support VMware vSphere Enterprise 1 CPU lyr 24x7 support VMware vSphere Enterprise 1 CPU 3yr 24x7 support VMware vSphere Enterprise Plus 1 CPU lyr 24x7 support VMware vSphere Enterprise Plus 1 CPU 3yr 24x7 support VMware vCenter Server Standard lyr support required VMware vCenter Server Standard 3yr support required Cisco UCS C210 M2 General Purpose Rack Mount Server 37 CONFIGURING the SERVER STEP 16 CHOOSE OPERATING SYSTEM MEDIA KIT Choose the optional operating system media listed in Table 19 Table 19 OS Media Product ID PID RHEL 6 SLES 11 MSWS 08R2 STHV RM MSWS 08RS ENHV RM MSWS 08R2 DCHV RM 38 PID Description RHEL 6 Recovery Media Only Multilingual SLES 11 media only mult
22. Description R210 2121605W UCS C210 M2 Srvr w 1PSU w o CPU mem HDD DVD or PCle card The R210 2121605W base server m Includes one power supply m Does not include CPU memory hard disk drives HDDs Solid State Drives SSDs plug in PCle cards or optional DVD RW drive o NOTE Use the steps on the following pages to configure the server with the components that you want to include Cisco UCS C210 M2 General Purpose Rack Mount Server 9 CONFIGURING the SERVER STEP 2 CHOOSE CPU S The standard CPU features are m Intel Xeon 5600 series Westmere EP or Intel Xeon 5500 series Nehalem CPUs m Intel 5520 chipset m Cache size of 4 8 or 12 MB Choose CPUs The available CPUs are listed in Table 3 Table 3 Available CPUs Intel Xeon Westmere EP x56xx Family Product ID PID Number yn pd ij COTE nsec ete A01 X0117 X5675 3 06 95 12 6 64GI s 1333 A01 X0102 X5670 2 93 95 12 6 6 4GT s 1333 A01 X0105 X5650 2 66 95 12 6 6 4GT s 1333 A01 X0109 E5640 2 66 80 12 4 5 86 GT s 1066 A01 X0120 E5649 2 53 80 12 6 5 86GT s 1333 UCS CPU E5645 E5645 2 40 80 12 6 5 86GT s 1333 A01 X0111 E5620 2 40 80 12 4 5 86 GT s 1066 A01 X0106 L5640 2 26 60 4 6 5 86 GT s 1333 A01 X0107 L5630 2 13 40 12 4 5 86 GT s 1066 A01 X0123 E5606 2 13 80 8 4 AB8GI s 1066 A01 X0108 15609 1 86 40 12 4 AB8GI s 1066 Notes 1 If higher or lower speed DIMMs are selected than what is shown in the table for a given CP
23. MM pair would be located on Channel B of CPU 1 For more information regarding memory see CPUs and DIMMs on page 47 16 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 4 CHOOSE RAID CONFIGURATION The base server motherboard comes with an integrated SATA RAID 0 1 controller which supports up to 4 SATA drives only the integrated controller does not support SAS drives Therefore a separate plug in PCle controller card is not required when ordering SATA drives and a RAID 0 or 1 configuration is desired You can use the built in SATA RAID 0 1 controller as described in the preceding paragraph or you can instead choose to implement a RAID configuration by using the optional mezzanine card on the server motherboard or by using an optional plug in PCle RAID controller card Cisco can provide factory configured RAID 0 1 1E 5 6 and 10 systems depending on the RAID implementation chosen and the number of drives ordered Factory configured RAID options are listed at the end of Table 6 Note that RAID levels 50 and 60 are supported on the 9280 4i4e and 9261 81 but are not factory configurable Choose RAID Options Choose one RAID controller one RAID configuration option and if desired the battery backup option listed in Table 6 Table 6 Available RAID Options Product ID PID PID Description RAID Controllers R2X0 ML002 LSI 1064E 4 port SAS 3 0G RAID Mezzanine Card m Installed on the
24. Recommended DIMM Combinations CPU Socket 1 CPU Socket 2 DIMM DIMM DIMM DIMM Bank 1 Bank 2 Bank 1 Bank 2 ee rece mem eel ae Deel Uus eel 2x8GB 2x8GB EL 3x4 GB 3x8 GB E 3x8GB 3x 8 GB 3 x 8 GB 3x8 GB Notes 1 Best performance configuration Total Memory Size 8 GB 1 CPU 16 GB 2 CPUs 12 GB 1 CPU 24 GB 2 CPUs 16 GB 1 CPU 32 GB 2 CPUs 24 GB 1 CPU 48 GB 2 CPUs 32 GB 1 CPU 64 GB 2 CPUs 36 GB 1 CPU 72 GB 2 CPUs 48 GB 1 CPU 96 GB 2 CPUs 60 GB 1 CPU 120 GB 2 CPUs 64 GB 1 CPU 128 GB 2 CPUs 72 GB 1 CPU 144 GB 2 CPUs 96 GB 1 CPU 192 GB 2 CPUs Cisco UCS C210 M2 General Purpose Rack Mount Server DIMM Max Clock rate 1333 MHz 1333 MHz 1333 MHz 1066 MHz 1333 MHz 1333 MHz 1333 MHz 1333 MHz 1066 MHz 1333 MHz 1333 MHz 1066 MHz 1333 MHz 800 MHz 800 MHz 800 MHz 800 MHz Total DIMMs in System 61 12 121 12 12 12 12 49 SUPPLEMENTAL MATERIAL Configuration Samples The following figures show examples of how DIMMs are populated for 1 CPU and 2 CPU systems Figure 8 Example of 24 GB DIMM Memory Combinations with One CPU 50 Cisco UCS C210 M2 General Purpose Rack Mount Server SUPPLEMENTAL MATERIAL Figure 9 Example of 96 GB DIMM Memory Combinations with Two CPUs 16 GB DIMM _ 16 GB DIMM 16 GB DIMM 8 GB DIMM nn RIEN nini _8 GB DIMM Cisco U
25. See Table 27 on page 49 for recommended DIMM combinations DIMMs can be used either in a one DIMM per Channel 1DPC configuration or in a two DIMMs per Channel 2DPC configuration There are blue and black DIMM slots Populate blue slots in a bank first Low voltage 1 35 V DIMM and standard voltage DIMM 1 5 V can be mixed in the same server Note that this causes the system BIOS to default to standard voltage operation Performance Mode See Low Voltage DIMM Considerations Low Voltage DIMM Considerations The C210 M2 server can be ordered with low voltage 1 35 V DIMMs or standard voltage 1 5 V DIMMs Note the following considerations 48 Low voltage DIMMs within the server must have the identical manufacturer type speed and size Low voltage DIMMs and standard voltage DIMMs can be mixed in the same server Note that this causes the system BIOS to default to standard voltage operation Performance Mode That is the server cannot operate in Power Saving Mode unless all DIMMs are low voltage DIMMs CPUs that have a maximum memory frequency less than 1333 MHz support low voltage DIMMs operating in Power Saving Mode only and do not support Performance Mode Cisco UCS C210 M2 General Purpose Rack Mount Server SUPPLEMENTAL MATERIAL Recommended Configurations Table 27 lists the recommended DIMM combinations for 1 and 2 socket CPU systems The DIMM combinations yielding the best performance are noted Table 27
26. U the DIMMs will be clocked at the lowest common denominator of CPU clock and DIMM clock For example Selecting lower speed DIMMs If you use an X5650 CPU which can support up to 1333 MHz DIMMs with 1066 MHz DIMMs the DIMMs will be clocked at the lower speed of 1066 MHz Selecting higher speed DIMMs If you use 1333 MHz DIMMs with an E5620 CPU which can support up to 1066 MHz DIMMs the DIMMS will be clocked at the lower speed of 1066 MHz 10 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER The available 5500 series CPUs are listed in Table 4 Table 4 Available Intel CPUs Xeon Nehalem x55xx Family product D PID ime Freq Pane CANE cores apt OO D N20 X00001 X5570 2 93 95 8 4 6 4 GT s 1333 N20 X00006 X5550 2 66 95 8 4 6 4 GT s 1333 N20 X00002 E5540 2 53 80 8 4 5 86 GT s 1066 N20 X00003 E5520 2 26 80 8 4 5 86 GT s 1066 N20 X00004 L5520 2 26 60 8 4 5 86 GT s 1066 N20 X00009 E5504 2 00 80 4 4 4 8 GT s 800 A01 X0113 E5506 2 13 80 4 4 4 8 GT s 800 Notes 1 If higher or lower speed DIMMs are selected than what is shown in the table for a given CPU the DIMMs will be clocked at the lowest common denominator of CPU clock and DIMM clock For example Selecting lower speed DIMMs if you use an X5570 CPU which can support up to 1333 MHz DIMMs with 1066 MHz DIMMs the DIMMs will be clocked at the lower speed of 1066 MHz Selecting higher speed DIMMs If you use 1333 MHz DIMMs with an E5506 CPU wh
27. UPPLEMENTAL MATERIAL RACKS The Cisco R42610 rack see Figure 12 is certified for Cisco UCS installation at customer sites and is suitable for the following equipment m Cisco UCS B Series servers and fabric interconnects m Cisco UCS C Series and select Nexus switches The rack is compatible with hardware designed for ElA standard 19 inch racks Rack specifications are listed in Table 28 Table 28 Cisco R42610 Rack Specifications Parameter Dimensions H x W x D Dimensions H x W x D with packaging Distance from front mounting rail to rear mounting rail Weight Weight with packaging Side panels included Equipment mounting Capacity Static load capacity Dynamic load capacity Standard Rack 78 74 x 24 x 43 38 in 2000 x 610 x 1102 mm 89 x 33 x 47 in 2261 x 838 x 1194 mm 29 2 in 741 mm 299 83 b 136 kg 354 Ib 161 kg Yes 42RU 2100 Ib 954 kg Not applicable Expansion Rack 78 74 x 23 58 x 43 38 in 2000 x 599 x 1102 mm 89 x 33 x 47 in 2261 x 838 x 1194 mm 29 2 in 741 mm 231 49 Ib 105 ko 284 Ib 129 kg No 42RU 2100 Ib 954 kg Not applicable o NOTE The AC input connector is an IEC 320 C 14 15 A 250 VAC power inlet Cisco UCS C210 M2 General Purpose Rack Mount Server 53 SUPPLEMENTAL MATERIAL Figure 12 Cisco R42610 Rack Front view door closed Front view door open Front view door removed 54 Cisco UCS
28. and ensures that the sensitive data on those drives is not compromised thereby reducing the risk of any potential liabilities This service also enables you to comply with regulatory local and federal requirements If your company has a need to control confidential classified sensitive or proprietary data you might want to consider one of the Drive Retention Services listed in Table 24 service e NOTE Cisco does not offer a certified drive destruction service as part of this S amp S Table 24 Drive Retention Service Options Service Description UCS Mission Critical Support Service With Drive Retention UCS Support Service With Drive Retention 42 Service Program Name UC CRIT DR UC SUPP DR Service Level GSP UCMD7 UCMD8 UCSD1 UCSD2 UCSD3 UCSD4 UCSD5 UCSD6 UCSD7 UCSD8 Cisco UCS C210 M2 General Purpose Rack Mount Server Service Level 24x7x4 Onsite 24x7x2 Onsite 8x5xNBD 8x5x4 24x7x4 24x7x2 8x5xNBD Onsite 8x5x4 Onsite 24x7x4 Onsite 24x7x2 Onsite Product ID PID CON UCMD7 R210WSFF CON UCMD8 R210WSFF CON UCSD1 R210WSFF CON UCSD2 R210WSFF CON UCSD3 R210WSFF CON UCSD4 R210WSFF CON UCSD5 R210WSFF CON UCSD6 R210WSFF CON UCSD7 R210WSFF CON UCSD8 R210WSFF CONFIGURING the SERVER Table 24 Drive Retention Service Options continued Service Description Mdb ld epee Service Level UCS Warranty Plus UC PLUS DR UCWD2 8x5x4 With Drive Retention UCWD3 24x7x4 UCWD4
29. ard ordered The cables can be different lengths however you would normally order two cables of equal lengths to connect to the primary and redundant network switching equipment Caveats The twinax cables listed in Table 10 can be ordered only for the following PCle cards N2XX ACPCIO1 Cisco UCS P81E Virtual Interface Card 2 port 10Gbps UCS PCIE BSFP Broadcom 57712 N2XX ABPCI02 Broadcom 57711 N2XX AEPCIO1 Emulex OCe10102 F N2XX AIPCIO1 Intel Dual Port Ethernet X520 N2XX AQPCIO1 Qlogic QLE 8152 CNA Cisco UCS C210 M2 General Purpose Rack Mount Server 25 CONFIGURING the SERVER Choose Optional SFP Modules Optical Cisco SFP modules are listed in Table 11 Table 11 Available SFP Modules Product ID PID PID Description SFP 10G SR 10GBASE SR SFP Module 850 nm multimode SR 3 3V LC connector with Digital Optical Monitoring DS SFP FC8G SW 8 Gbit SFP Module 850 nm multimode SR 3 3V LC connector with Digital Optical Monitoring Approved Configurations 1 Choose Up to Two SFP Modules for Each Network Card Ordered B You may choose one or two SFP optical modules cables for each network card ordered You would normally order two modules for connecting to the primary and redundant network switching equipment With the SFP optical modules you can use common fiber optic cables widely available See Figure 5 on page 27 for typical SFP and twinax connections to the network
30. ats B DIMM voltage You can mix dual voltage DIMMs operate at either 1 5 V or 1 35 V and single voltage DIMMs operate at only 1 5 V Dual voltage DIMMs can be operated in either of these modes e Power Saving Mode at a maximum speed of 1066 MHz e Performance Mode at a maximum speed of 1333 MHz If you mix both types of DIMMs in your configuration the server forces all DIMMs to operate in Performance Mode m Memory mirroring If you choose the Memory RAS option be aware that it is available only with an even number of memory channels For example if you choose six DIMMs and select RAS Cisco UCS C210 M2 General Purpose Rack Mount Server 15 CONFIGURING the SERVER mirroring will go into effect on only two channels with two DIMMS per channel you Cannot implement RAS on three channels In this case two DIMMS would go unused Q NOTE For memory mirroring DIMM pairing across buses must be identical If you only have two DIMMs they need to be the same PID because you have one DIMM on each of two buses If you have four DIMMs in a 2 CPU system for example you can have two 4 GB and two 8 GB DIMMs One 4 GB 8 GB DIMM pair would located on Channel A of CPU 1 and one 4 GB 8 GB DIMM pair would be located on Channel D of CPU 2 If you have four DIMMs in a 1 CPU system for example you can have two 4 GB and two 8 GB DIMMs One 4 GB 8 GB DIMM pair would located on Channel A of CPU 1 and one 4 GB 8 GB DI
31. cards Caveats The SFP 10G SR optical module listed in Table 11 should be ordered only for the following PCle cards as they do not come by default with any optical modules N2XX ACPCIO1 Cisco UCS P81E Virtual Interface Card 2 port 10Gbps UCSC PCIE BSFP Broadcom 57712 N2XX ABPCI02 Broadcom 57711 N2XX AEPCIO1 Emulex OCe10102 F The DS SFP FC8G SW optical module listed in Table 11 should be ordered only for the following PCle cards as they do not come by default with any optical modules N2XX AEPCIO5 Emulex LPe 12002 Dual Port 8Gb Fibre Channel HBA 26 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER Figure 5 Network Card Connections Network PCle Card Optical SFP Modules Redundant Top of Rack Access Switches P ES Ee Fiber Optic Cables Network PCle Card Twinax Copper Cables Redundant Top of Rack Access Switches Cisco UCS C210 M2 General Purpose Rack Mount Server 27 CONFIGURING the SERVER STEP 9 CHOOSE OPTIONAL DVD RW DRIVE An optional DVD RW optical drive with dual layer DL media support may be ordered The drive is listed in Table 12 Table 12 Available DVD RW Drive Product ID PID PID Description R210 ODVDRW DVD RW Drive for UCS C210 M2 Rack Servers 28 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 10 ORDER OPTIONAL REDUNDANT POWER SUPPLY The C210 M2 server can accommodate t
32. eae ave ae oe ha Ra eR Bo oS STEP 16 CHOOSE OPERATING SYSTEM MEDIA KIT 0 0 00 Ry STEP 17 CHOOSE OPTIONAL VALUE ADDED SOFTWARE enn STEP 18 CHOOSE SERVICE and SUPPORT LEVEL eee I OPTIONAL STEP ORDER RACK S 200 cee eee eee eee eee eee OPTIONAL STEP ORDER PDU 1 cee ee es SUPPLEMENTAL MATERIAL 0 0c eee ee eee ees CHASSIS xcu a winter V Pie a 3 905 374 4 EEEE AEAEE EEEE ETETE 3d 3 UO CPUs and DIMMS 1 ha ha hh ens PINVSiCal LOVCUL xu ucc ee cara oe oe ee HEIC RECON eae CUR n Memory Population Rules err Low Voltage DIMM Considerations aoaaa aaa RI Ie Recommended Configurations a Configuration Samples ee hh oriens SAS EXTENDER and SAS EXPANDER eR ns SASqEXPSDUBI an or de 3E ded de ni edd UE 5 0 RUE S deed 3 3 9 9 39 SUE 3 SAS EXPANUET 644 6 ru qo wae ORACLE EO p ed Ur ee ole di Re ded RACKS ma enen ekain nr POUS fu ame FOES BED Oo ee Sea dee knee aoe eee Gos POWER SUPPLIES 64 664 eo ee haea bob eo es eh eee ee OE eae Be VM CABLE 6 a4 ee OO Oe eh de ee ek ea a oe a ee daken ME Motherboard USB Port 4 saa eed Gow week wan ee ee Od Ewe ee ee ds TECHNICAL SPECIFICATIONS 00 cee ee eee ees Dimensions and Weight es Power Specifications 5 se ier ded dee qe ae deo ee ee ale de Environmental Specifications sene Compliance Requirements 0 ee Cisco UCS C210 M2 General Purpose Rack Mount Server OVERVIEW OVERVIEW
33. fied Computing Warranty Plus Service You can choose from several levels of advanced parts replacement coverage including onsite parts replacement in as little as two hours Warranty Plus provides remote access any time to Cisco support professionals who can determine if a return materials authorization RMA is required You can choose a service listed in Table 23 Table 23 UCS Computing Warranty Plus Service Product ID PID On Site Description CON UCW2 R210W No UC Warranty Plus 8x5x4 CON UCW3 R210W No UC Warranty Plus 24x7x4 CON UCW4 R210W No UC Warranty Plus 24x7x2 CON UCW5 R210W Yes UC Warranty Plus 8X5XNBD CON UCW6 R210W Yes UC Warranty Plus 8X5X4 CON UCW7 R210W Yes UC Warranty Plus 24x7x4 CON UCW8 R210W Yes UC Warranty Plus 24x7x2 Cisco UCS C210 M2 General Purpose Rack Mount Server 41 CONFIGURING the SERVER Unified Computing Drive Retention Service With the Cisco Unified Computing Drive Retention UCDR service you can obtain a new disk drive in exchange for a faulty drive without returning the faulty drive In exchange for a Cisco replacement drive you provide a signed Certificate of Destruction CoD confirming that the drive has been removed from the system listed is no longer in service and has been destroyed Sophisticated data recovery techniques have made classified proprietary and confidential information vulnerable even on malfunctioning disk drives The UCDR service enables you to retain your drives
34. given here is an estimate for a fully configured system and will vary depending on the number of peripheral devices and power supplies Power Specifications The general power specifications for the C210 M2 server are listed in Table 31 Table 31 UCS C210 M2 Power Specifications Description Specification AC input voltage 100 to 120 VAC nominal 200 to 240 VAC nominal Range 90 to 264 VAC AC input frequency 50 to 60 Hz nominal Range 47 to 63 Hz Maximum AC input current 8 A at 100 VAC Maximum AC inrush current 30 A peak sub cycle duration Maximum output power for each 650 W power supply Power supply output voltage Main power 12 VDC Standby Power 5 VDC Power supply efficiency 92 Peak complies with 80Plus Gold Standard Cisco UCS C210 M2 General Purpose Rack Mount Server 59 TECHNICAL SPECIFICATIONS o NOTE AC input connector is an IEC 320 C 14 15A 250VAC power inlet For configuration specific power specifications use the Cisco UCS Power Calculator at this URL http www cisco com assets cdc content elements flash dataCenter cisco ucs power calculator As an example using the calculator we can determine the approximate power for the following C210 M2 server configuration B Voltage 2115 VAC Power Supplies 22 Processors 2 CPUs Intel Xeon 2 93 GHz X5670 Memory DIMMs 6 x 16 GB Disk Drives 216 x 1 TB PCle Cards 24 B PCle RAID Card 1 The resulting power calculations are m Idle Power
35. ich can support up to 800 MHz DIMMs the DIMMS will be clocked at the lower speed of 800 MHz Cisco UCS C210 M2 General Purpose Rack Mount Server 11 CONFIGURING the SERVER Approved Configurations 1 Single CPU configurations m Choose any one CPU listed in Table 3 on page 10 or Table 4 on page 11 2 Two CPU Configurations m Choose two identical CPUs from any one of the rows of Table 3 on page 10 or Table 4 on page 11 Caveats m You can select either one processor or two identical processors m For optimal performance select DIMMs with the highest clock speed for a given processor see Table 5 on page 14 If you select DIMMs whose speeds are lower or higher than that shown in the tables suboptimal performance will result 12 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 3 CHOOSE MEMORY The standard memory features are B DIMMs Clock speed 800 MHz 1066 MHz or 1333 MHz Ranks per DIMM 1 2 or 4 Operational voltage single voltage 1 5 V or dual voltage 1 35 V 1 5 V Registered B DDR3 ECC registered DIMMs RDIMMs supporting Intel SDDC m Memory is organized with three memory channels per CPU with up to two DIMMs per channel DPC as shown in Figure 4 Figure 4 C210 M2 Memory Organization intel CPU 2 Bank 2 Channel D Channel A Bank 1 Slot 2 Bank 2 Channel E Channel B Bank 1 Slot 4 Bank 2 Channel F Channel C Bank 1 Slot 6
36. ilingual Windows Svr 2008 R2 ST 1 4CPU 5CAL Media Windows Svr 2008 R2 EN 1 8CPU 25CAL Media Windows Svr 2008 R2 DC 1 8CPU 25CAL Media Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 17 CHOOSE OPTIONAL VALUE ADDED SOFTWARE You can select from a variety of value added software listed in Table 19 Table 20 Value Added Software Product ID PID PID Description BMC 001 BMC BladeLogic CM for Virtualized Cisco Servers BMC 001 COMP BMC Blade Logic Compliance VM Bundle 2 Socket Server BMC 002 BMC BladeLogic CM for Physical Cisco Servers BMC 002 COMP BMC Blade Logic Compliance Single OS BMC 012 BMC BPPM Per Server VMW VCS 1A VMware vCenter Server Standard lyr 24x7 support VMW VCS 3A VMware vCenter Server Standard 3yr 24x7 support NIK VLEM UCS 1 Cisco Nexus 1000V License PAK for 1 Virtual Ethernet module N1K CSK9 UCS 404 Cisco Nexus 1000V VSM Virtual Appliance Software Cisco UCS C210 M2 General Purpose Rack Mount Server 39 CONFIGURING the SERVER 40 STEP 18 CHOOSE SERVICE and SUPPORT LEVEL A variety of service options are available as described in this section Unified Computing Warranty No Contract If you have noncritical implementations and choose to have no service contract the following coverage is supplied m Three year parts coverage Next business day NBD parts replacement eight hours a day five days a week 90 day software warranty on media Downloads of
37. latory Compliance Requirements Parameter Description Regulatory Compliance Products should comply with CE Markings per directives 2004 108 EC and 2006 95 EC Safety UL 60950 1 Second Edition CAN CSA C22 2 No 60950 1 Second Edition EN 60950 1 Second Edition IEC 60950 1 Second Edition AS NZS 60950 1 GB4943 2001 EMC Emissions 47CFR Part 15 CFR 47 Class A AS NZS CISPR22 Class A CISPR22 Class A EN55022 Class A ICES003 Class A VCCI Class A EN61000 3 2 EN61000 3 3 KN22 Class A CNS13438 Class A EMC Immunity EN55024 CISPR24 EN300386 KN24 staende CISCO Americas Headquarters Asia Pacific Headquarters Europe Headquarters Cisco Systems Inc Cisco Systems USA Pte Ltd Cisco Systems International BV Amsterdam San Jose CA Singapore The Netherlands Cisco has more than 200 offices worldwide Addresses phone numbers and fax numbers are listed on the Cisco Website at www cisco com go offices Cisco and the Cisco Logo are trademarks of Cisco Systems Inc and or its affiliates in the U S and other countries A listing of Cisco s trademarks can be found at www cisco com go trademarks Third party trademarks mentioned are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 1005R 62 Cisco UCS C210 M2 General Purpose Rack Mount Server
38. mezzanine connector inside the UCS C210 M2 server m Supports up to four SAS or SATA drives with the factory default SAS Extender or the optional SAS Expander installed You cannot mix SSD and HDD drive types You cannot mix SAS and SATA drives m No battery backup B Factory configured RAID options RAID 0 1 or 1E UCSC RAID C 4I 4E LSI MegaRAID SAS 9280 4i4e four internal and four external ports m Takes up one of five available PCle slots must be installed in slot 4 m Supports up to 4 internal SAS or SATA drives no mixing plus external J BOD expansion with the factory default SAS Extender installed You cannot mix SSD and HDD drive types m Battery backup option available see the battery backup PID section in this table B Factory configured RAID options RAID 0 1 5 6 10 see the RAID PIDs section in this table Cisco UCS C210 M2 General Purpose Rack Mount Server 17 CONFIGURING the SERVER Table 6 Available RAID Options continued Product ID PID PID Description R2XX PL003 LSI MegaRAID SAS 9261 8i RAID 0 1 5 6 10 m Takes up one of five available PCle slots must be installed in slot 4 m Supports up to eight internal SAS or SATA drives with the factory default SAS Extender installed You can mix SAS and SATA drive types but you cannot mix HDD and SSD drive types m Supports up to 16 internal SAS or SATA drives with the optional SAS Expander installed You can mix SAS and SATA drive types but you ca
39. nly with the same type of card 22 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 7 CHOOSE PCle OPTION CARD S The standard PCle card offerings are m Ethernet m Fibre Channel B iSCSI B Virtual Interface Card VIC Choose PCle Option Cards The available PCle option cards are listed in Table 9 Table 9 Available PCle Option Cards Product ID PID PID Description et Converged Network Adapters CNA N2XX ACPCIO1 Cisco UCS P81E Virtual Interface Card 2 port 10Gbps Full N2XX AEPCIO1 Emulex OneConnect OCe10102 F CNA 2 port 10Gbps Half UCSC PCIE BSFP Broadcom 57712 Dual Port 10Gb SFP w TOE iSCSI Half Network Interface Cards NICs N2XX ABPCIO2 Broadcom 57711 Dual Port 10GbE NIC w TOE iSCSI Half N2XX ABPCIO3 M3 Broadcom 5709 Quad Port 1Gb w TOE iSCSI for M3 Servers Half N2XX ABPCIO1 M3 Broadcom 5709 Dual Port 1Gb w TOE iSCSI for M3 Servers Half N2XX AQPCI01 Qlogic QLE 8152 CNA 2port 10Gb SFP Copper Half N2XX AIPCIO2 Intel Quad port GbE Controller E1G44ETG1P20 Half N2XX AIPCIO1 Intel X520 Dual Port 10Gb SFP Adapter Half N2XX AMPCIO1 Mellanox ConnectX 2 EN with dual 10GbE SFP ports Half Host Bus Adapters HBAs N2XX AEPCIO3 Emulex LPe 11002 Dual Port 4Gb Fibre Channel HBA Half N2XX AEPCIO5 Emulex LPe 12002 Dual Port 8Gb Fibre Channel HBA Half N2XX AQPCIO3 Qlogic QLE2462 Dual Port 4Gb Fibre Channel HBA Half N2XX AQPCIO5 Qlogic QLE2562 Dual Port 8Gb Fibre Channel HBA Half Cisco UCS C2
40. nnot mix HDD and SSD drive types m Includes 512 MB of write cache m Battery backup option available see the battery backup PID section in this table B Factory configured RAID options RAID 0 1 5 6 10 see the RAID PIDs section in this table RAID Battery Backup Option not available with mezzanine card R2XX LBBU2 Battery Backup RAID Configuration note Mezzanine card supports only RAID 0 1 and 1E R2XX RAIDO Factory pre configured RAID striping option Enable RAID 0 Setting Requires a minimum of 1 hard drive R2XX RAID1 Factory pre configured RAID mirroring option Enable RAID 1 Setting Requires exactly 2 drives with same size speed capacity R2XX RAID5 Factory pre configured RAID option Enable RAID 5 Setting Requires minimum 3 drives of same size speed capacity R2XX RAID6 Factory pre configured RAID option Enable RAID 6 Setting Requires minimum 4 drives of same size speed capacity R2XX RAID10 Factory pre configured RAID option Enable RAID 10 Setting Requires an even number of drives minimum 4 drives of same size speed Capacity NOTE No RAID option can be chosen if you have one of the following configurations o e A mix of SAS and SATA drives e No drives 18 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER Approved Configurations 1 Integrated SATA RAID 0 1 controller m Choose none of the options listed in Table 6 In this case the integrated RAID 0 1 contr
41. nstalled only in PCle slot 1 All cards will fit in any slot B The MegaRAID cards LSI MegaRAID SAS 9280 4i4e or LSI MegaRAID SAS 9261 8i must be installed in PCle slot 4 Refer to Figure 3 on page 5 for PCle slot numbering B To help ensure that your operating system is compatible with the card you have selected please check the Hardware Compatibility List at this URL http www cisco com en US products ps10477 prod technical reference list html 24 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 8 ORDER OPTIONAL NETWORK CARD ACCESSORIES Copper twinax cables and SFP optical modules may be ordered to support the two port network cards that are available with the server Choose Optional Twinax Cables Copper twinax cables are listed in Table 10 You can choose cable lengths of 1 3 5 7 or 10 meters The two longer cables 7 and 10 meters are active which means that they contain active components within the SFP housing to improve signal quality Table 10 Available Twinax Cables Product ID PID PID Description SFP H10GB CU1M 10GBASE CU SFP Cable 1 M SFP H10GB CU3M 10GBASE CU SFP Cable 3 M SFP H10GB CU5M 10GBASE CU SFP Cable 5 M SFP H10GB ACU7M 10GBASE CU SFP Cable 7 M SFP H10GB ACU10M 10GBASE CU SFP Cable 10 M Approved Configurations 1 Choose Up to Two Twinax Cables for Each Network Card Ordered m You may choose one or two twinax cables for each network c
42. o not select a SAS Expander the SAS Extender comes standard with the UCS C210 M2 server chassis The SAS Extender supports up to eight disk drives The SAS Extender option is not field upgradeable to a SAS Expander Both the SAS Extender and SAS Expander however are field replaceable You can replace an extender or expander only with the same type of card If desired select the SAS Expander listed in Table 7 Table 7 SAS Expander Product ID PID Description R210 SASXPAND SAS Pass Thru Expander srvr requiring gt 8 HDDs For more information about the SAS Expander and SAS Extender see SAS EXTENDER and SAS EXPANDER on page 52 20 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 6 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES The standard disk drive features are B 2 5 inch small form factor B Hot pluggable B Sled mounted Choose Drives The available drives are listed in Table 8 Table 8 Available Hot Pluggable Sled Mounted HDDs and SSDs Product ID PID PID Description sibi Capacity HDDs A03 D146GC2 146GB 6 Gb SAS 15K RPM SFF SAS 146 GB A03 D300GA2 300 GB 6 Gb SAS 10K RPM SFF HDD SAS 300 GB UCS HDD300GI2F105 4 300GB 6Gb SAS 15K RPM SFF HDD SAS 300 GB A03 D500GC3 500 GB 6 Gb SATA 7 2K RPM SFF SATA 500 GB A03 D600GA2 600 GB 6 Gb SAS 10K RPM SFF HDD SAS 600 GB UCS HDD900GI2F106 4 900GB 6Gb SAS 10K RPM SFF HDD SAS 900 GB A03 DITBSATA 1 TB 6 Gb SATA 7 2K RPM SFF HDD SATA 1 TB SSDs
43. o order spare racks available only as next day replacements For more information about the R42610 rack see RACKS on page 53 44 Cisco UCS C210 M2 General Purpose Rack Mount Server OPTIONAL STEP ORDER PDU OPTIONAL STEP ORDER PDU An optional power distribution unit PDU is available from Cisco for the C Series rack servers including theC210 M2 server This PDU is available in a zero rack unit RU style see Table 25 Table 26 PDU Options Product ID PID PID Description RP208 30 2P U 2 Zero RU PDU For more information about the PDU see PDUs on page 55 Cisco UCS C210 M2 General Purpose Rack Mount Server 45 SUPPLEMENTAL MATERIAL SUPPLEMENTAL MATERIAL CHASSIS An internal view of the C210 M2 chassis with the top cover removed is shown in Figure 6 Figure 6 C210 M2 With Top Cover Removed Power PCle PCle Supplies slots 1 2 and 3 slots 4 and 5 ier X mr E xm i Ee rar vam nml assembly T li rh s DIMMs Power Supply 2 Power Supply 1 s Front Panel Disk Drives 46 Cisco UCS C210 M2 General Purpose Rack Mount Server SUPPLEMENTAL MATERIAL CPUs and DIMMs Physical Layout Each CPU has three DIMM channels B CPU has channels A B and C B CPU2 has channels D E and F Each DIMM channel has two banks Bank 1 and Bank 2 The blue colored DIMM banks are for Bank 1 and the black colored DIMM banks are for Bank 2 As an example
44. oe 8 TI 25 J5 LL 195911 L aa je Locator LED Locator Button 6 Memory fault LED Network Activity LED Power supply fault LED t System fault LED Console connector with supplied KVM cable provides DB15 video DB9 serial and two USB 2 0 connectors Hard drives up to 16 2 5 HDD Power button Power status LED DVD RW drive with dual layer DL media support optional CPU fault LED For more information regarding the KVM cable connection see KVM CABLE on page 57 4 Cisco UCS C210 M2 General Purpose Rack Mount Server DETAILED VIEWS Chassis Rear View Figure 3 shows the external features of the rear panel Chassis Rear View Figure 3 PCle Slot 4 PCle Slot 1 PCle Slot 2 PCle Slot 5 ZL6S6L Televereleleleleleleleieler 1 DOOOOODOOOOOOOO DOT CODO sjelli ele OOOO wine sie eelelsieleieie e sie C 2 CO IODOOOOOOOGOODOO eol DOODCOCOCOL jee LIOOCOCOLC A C X s Te E DOOD TAM OOOO OOK OOOK INI Osea 5 Serial connector DB9 En Power supply up to 2 10 100 1000 Megabit Ethernet ports 2 USB 2 0 connectors 2 Standard profile PCle card slots five total fa ST I ec J _ O e J c ced aD D c J ap Cc _ ap G J LLI O O co O vd _Sot5 L Sot PCle Slot Numbering rear server view enkle pp Cisco UCS C210 M2 General Purpose Rack Mount Server BASE SERVER STANDARD
45. oller will be used 2 Optional RAID controller m Choose one of the RAID controllers options with or without battery backup listed in Table 6 3 Optional RAID configuration m Choose one of the RAID configuration options listed in Table 6 o Caveats NOTE If an optional RAID configuration is not chosen the disks will be configured as a J BOD B The MegaRAID cards LSI MegaRAID SAS 9280 4i4e or LSI MegaRAID SAS 9261 8i must be installed in PCle slot 4 Refer to Figure 3 on page 5 for PCle slot numbering B f you choose the mezzanine RAID controller card you will still have all five PCle slots available for adding optional cards B The two optional plug in RAID controllers are each half height PCle cards If you choose one of these optional cards you will still have four slots available for adding optional PCle cards B You can choose only one RAID controller integrated controller mezzanine card controller or one plug in PCle controller m You can choose an optional RAID configuration RAID 0 1 5 6 or 10 which is pre configured at the factory If you do not choose a RAID configuration the disks will be configured as a J BOD Cisco UCS C210 M2 General Purpose Rack Mount Server 19 CONFIGURING the SERVER STEP 5 ORDER SAS EXPANDER AS NEEDED You must order a SAS Expander if the system will have more than eight disk drives or you plan to upgrade to over eight disk drives in the future If you d
46. rations SIO fan speed control Platform Environment Control Interface PECI and voltage monitoring Cisco UCS C210 M2 General Purpose Rack Mount Server 7 CONFIGURING the SERVER CONFIGURING the SERVER Follow these steps to configure the Cisco UCS C210 M2 General Purpose Rack Server STEP 1 VERIFY BASE SKU page 9 STEP 2 CHOOSE CPU S page 10 STEP 3 CHOOSE MEMORY page 13 STEP 4 CHOOSE RAID CONFIGURATION page 17 STEP 5 ORDER SAS EXPANDER AS NEEDED page 20 STEP 6 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES page 21 STEP 7 CHOOSE PCle OPTION CARD S page 23 STEP 8 ORDER OPTIONAL NETWORK CARD ACCESSORIES page 25 STEP 9 CHOOSE OPTIONAL DVD RW DRIVE page 28 STEP 10 ORDER OPTIONAL REDUNDANT POWER SUPPLY page 29 STEP 11 CHOOSE AC POWER CORDS page 30 STEP 12 ORDER TOOL LESS OPTIONAL RAIL KIT page 33 STEP 13 ORDER OPTIONAL CABLE MANAGEMENT ARM page 34 STEP 14 ORDER A TRUSTED PLATFORM MODULE page 35 STEP 15 CHOOSE OPERATING SYSTEM page 36 STEP 16 CHOOSE OPERATING SYSTEM MEDIA KIT page 38 STEP 17 CHOOSE OPTIONAL VALUE ADDED SOFTWARE page 39 STEP 18 CHOOSE SERVICE and SUPPORT LEVEL page 40 OPTIONAL STEP ORDER RACK s on page 44 OPTIONAL STEP ORDER PDU on page 45 8 Cisco UCS C210 M2 General Purpose Rack Mount Server CONFIGURING the SERVER STEP 1 VERIFY BASE SKU Verify the product ID PID of the base server as shown in Table 2 Table 2 PID of the Base C210 M2 Rack Server Product ID PID
47. ver providing a DB9 serial connector a VGA connector for a monitor and dual USB ports for a keyboard and mouse With this cable you can create a direct connection to the operating system and the BIOS running on the server The KVM cable ordering information is listed in Table 29 Table 29 KVM Cable Product ID PID PID Description 37 1016 01 KVM Cable Figure 15 KVM Cable m E S md m gt y A 192621 HR Connector to server front panel VGA connector for a monitor DB 9 serial connector Two port USB connector for a mouse and keyboard Cisco UCS C210 M2 General Purpose Rack Mount Server 57 SUPPLEMENTAL MATERIAL Motherboard USB Port The C210 M2 motherboard has a general purpose USB socket as shown in Figure 16 Figure 16 Motherboard USB Port V Gi 7 a Fan j Jj had 3 Ty bos vl k Internal USB socket t i y a y VAr W VA A A TR Ax mmm aA KA mm AV m CAT NA SCA A SCA m A c AC AC AS A AMD 58 Cisco UCS C210 M2 General Purpose Rack Mount Server TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Dimensions and Weight Table 30 UCS C210 M2 Dimensions and Weight Parameter Value Height 3 45 in 8 76 cm Width 17 39 in 44 17 cm Depth 28 35 in 72 01 cm Front Clearance 3 in 7 62 cm Side Clearance in 2 54 cm Rear Clearance 6 in 15 24 cm Weight 50 70 Ibs 23 kg Notes 1 The system weight
48. wo power supplies Only one power supply is required One 650 W power supply ships with the base server chassis You can order an optional redundant power supply listed in Table 13s Table 13 Redundant Power Supply Product ID PID PID Description R2X0 PSU2 650W SB 650 W power supply w added 5A Standby for UCS C200 or C210 Cisco UCS C210 M2 General Purpose Rack Mount Server 29 CONFIGURING the SERVER STEP 11 CHOOSE AC POWER CORDS Select the appropriate AC power cords listed in Table 14 You may select a minimum of no power cords and a maximum of two power cords If you select the option R2XX DMYMPWRCORD no power cord is shipped with the server Table 14 Available Power Cords Product ID PID PID Description Images R2XX DMYMPWRCORD No power cord dummy PID to Not applicable allow for a no power cord option CAB N5K6A NA Power Cord 200 240V 6A North America I m bee E Cordset rating 10 A 250 V ength 8 2 ft Connector IEC60320 C13 7 CAB AC 250V 13A Power Cord NEMA L6 20 250V 20A plug IEC320 C13 receptacle North America ur ise et yos dl Erato Tato Eee 2 CAB C13 C14 MPR Power Cord recessed receptacle
Download Pdf Manuals
Related Search