Chief JWDIWVB flat panel wall mount
Contents
1. exists for movement of display and that cables will not be pinched by installation of cover H or screws J 3 Carefully insert cables in cavity located in lower portion of mount arm See Figure 6 4 Using Phillips screwdriver install cover H with two screws J See Figure 6 Cable Path typical Figure 6 JWDIW Series Installation Instructions Optional Trim Installation 1 Remove paper covering adhesive from tape squares L and affix three tape squares to inside lower flange of each trim piece B See Figure 7 Orient trim pieces B See Figure 7 Remove paper covering adhesive back from tape squares L on trim and press trim B against inner wall of box See Figure 7 ee 4 Figure 7 ADJUSTMENTS PIVOT SWING ARM Tension 1 Using 3 16 hex key P slightly loosen or tighten the pivot swing tension adjustment screw s as necessary See Figure 8 Using 7 32 hex key Q slightly loosen or tighten the adjustment screw at end of swing arm See Figure 8 Figure 8 DISPLAY ROLL PITCH YAW Tension k a e w N Disconnect all wires and cable from the display Remove two Lower screws securing display to Centris cup Loosen two Upper screws securing display Lift display upward and away from mount Using 3 16 hex key P turn the tension adjustment screw clockwise to increas2. INSTALLATION INSTRUCTIONS Medium Flat Panel In Wall Swing Arm Mount CHIEF JWDIW Series Our Mounts Your Vision JWDIW Series Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are trademarks of Milestone AV Technologies Inc All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipm
3. d hole in the MAC501 bottom gee support plate The bumper mounting bracket is installed on the D Q side opposite the side used for installing the JWDIW swing arm A q See Figure 2 ad Install Bumper s 1 Install two bumpers G to bumper mounting bracket F See Figure 1 NOTE A screwdriver may be required to push bumper into hole in bumper mounting bracket Lower Support Plate 2 Secure bumper mounting bracket F to MAC501 on whichever side the arm is going to be retracted using two Phillips pan head screws N See Figure 1 Figure 2 6 Secure swing arm to MAC501 using four button head cap screws C four lock washers D and four flat washers E See Figure 3 1 7 Cover remaining four openings in back of MAC501 with four Secure on screw covers K See Figure 3 6S either side Secure on either side 2 N x2 Figure 1 3 Align bottom of swing arm pivot pin with hole in lower support plate See Figure 2 Figure 3 4 Lower swing arm until pivot pin rests in hole in lower support plate See Figure 2 Installation Instructions JWDIW Series Display Installation NOTE Ifthe display being installed has a 100x100 VESA mounting pattern no interface bracket is required and the display can be mounted directly to the Centris cup as outlined below NOTE If the display being installed requires an interface b
4. e tension or counter clockwise to decrease tension See Figure 9 Re install display Figure 9 Installation Instructions JWDIW Series JWDIW Series Installation Instructions O CH E F USA international Our Mounts Your Vision Europe Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific 8805 000241 RevC 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 11 09 TnP TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 7 S em o 0 iS T Consume
5. ent or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 75 Ibs 34 kg Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher C
6. have de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Installation Instructions JWDIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS eo 3 16 7 32 Included Included x1 SP C 4 D 4 E 4 5 16 18 x 5 8 5 16 1 4 Interface Bracket 6 ie a Ki i G 2 ne 8 32 x 1 2 including hardware D gy N R R 4 N 2 P 1 Q 1 4 08 x 1 2 3 16 7 32 an JWDIW Series Installation Instructions i 5 Align four mounting holes in swing arm mounting bracket Installation with four mounting oles in MACSO1 See Figure 2 The following procedure assumes that a Chief Listed Model MAC501 In Wall accessory has previously been installed following the installation instructions provided by the manufacturer If a MAC501 is not installed or there are any other questions regarding the installation of this accessory immediately contact a Chief Customer Service representative Swing Arm D Mounting Bracket m WARNING IMPROPER INSTALLATION CAN LEAD TO O MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT deviate from installation instructions provided DO NOT substitute 9 hardware D The MAC501 is designed to accommodate 4 1 2 of right or left display offset This is accomplished by aligning the JWDIW with NU either the right hand or left han
7. racket refer to the interface bracket installation instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes Ensure that screws are not too long WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris cup 1 Start two M4 x 8mm Phillips pan head screws included in hardware kit into upper mounting holes in display back See Figure 4 NOTE Leave at least 1 8 of each screw protruding out back of display P Figure 4 2 Align two screws in display back with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes See Figure 5 3 Install two more of the same screws through lower mounting holes in Centris cup and into display back See Figure 5 4 Tighten all hardware 5 Route cables and wires to display Figure 5 Cable Management 1 Attach all cables to display 2 If necessary use cable tie mounts M and cable ties R to secure cables within MAC501 A CAUTION Ensure that adequate cable slack
Download Pdf Manuals
Related Search