Axis Pendant Vandal Dome Housing
Contents
1. Keyhole Slots Locking Screw oe Turn the camera counter clockwise oO When the locking buttons hit the end of the keyhole slots tighten the locking screw INSTALLING THE HOUSING ASSEMBLY J Be sure the bracket is properly and securely N mounted to a supporting structure capable of rigidly m holding the weight of the entire unit NOTE This unit is designed for operation in an upright position Installing the product upside down may cause damage to the internal equipment and will void the warranty 1 This unit includes a 1 2 NPT housing for a standard 1 2 NPT pipe The housing can be used with other brackets designed with 1 2 male pipe threads such as the UNI WMB1 wall mount brackets 2 Attach the housing coupling Figure 3 NOTE Pipe threads should be clean and rust free Use the Teflon tape included with the housing on the threads Add thread sealing tape Figure 3 3 Mount the housing assembly to the mounting bracket and housing coupling A safety cable is included with the housing to temporarily hold it while making wiring connections Loop the safety cable over one of the set screws on the housing coupling and make the appropriate connections using the 2 screw down connectors supplied 2 Undo the safety cable and twist the housing onto the housing coupling Secure all 3 setscrews provided on the housing coupling Figure 4 Set screws Figure 4 REMOVI2. A CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance servicing instructions in the literature accompanying the appliance UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure to save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions SERVICE If the unit ever needs repair service the customer should contact Videolarm 1 800 554 1124 for authorization to return and shipping instructions TECHNICAL SUPPORT If technical support is needed Videolarm has set up a 24 hour technical support line for their customers 24 HOUR TECHNICAL SUPPORT 1 800 554 1124 ELECTRICAL SPECIFICATIONS OUTDOOR ONLY 2 Open the housing assembly box Note there is a small roll of Teflon Tape th
3. the housing packet slots Over the screws in the housing Slide the bracket Cable Tie Mounts forward and the tighten the captive screw on the bracket aptive screw SS ji mu 12 Now grab the camera assembly and connector the RJ45 cable and the input cable to the camera FOR REFERENCE ONLY 9 Installing Axis 233 Camera 1 Note the position of the mounting holes on the camera 4 Now remove the Base Bracket bracket see diagram below Camera Bracket Mounting holes Mounting holes for housing 2 Since the 233 camera operates on 24vac the power board that is located inside the housing is not needed The remove the power board start by loosening the screws on the terminal block and disconnect the orange and red wires 3 With a Phillips head screwdriver remove the 4 machine screws holding the power board to the base bracket 5 Now attach 4 1 spacers located in the packet that Remove the power board came with the housing to the base bracket Attach 4 1 spacers Installing Axis 233 Camera cont 6 Mount the Axis 233 camera bracket and Q R plate Quick 7 Place the Quick Release plate onto the bottom of the Release plate as shown camera Make sure that the locking the AXIS 233 Quick Release Keyhole Slots ae ne en e Q R plate camera line up with TT the keyhole slots on the Q R plate Slide the camera into the keyhole slots by targeting the locking screw s
4. NG AND ATTACHING THE DOME ASSEMBLY 1 Attach the dome assembly to the housing top by lining up the three pins with the three keyhole slots Insert the dome assembly into the housing and then rotate the dome assembly clockwise Then tighten the 3 screws on the front of the dome assembly 2 Remove the protective film from the dome 3 Clean the outside of the dome Chart A Wiring Color Code Power and Control Inputs Outside of housing Camera Power 24 VAC Red 2 Camera Power 24 VAC Orange 3 Accessory Power 24 VAC Yellow 4 Accessory Power 24 VAC Green Separate Power Supplies for Camera and Accessory Power Camera 25 watts VA 24 VAC Class 2 Only Accessory 27 wattts VA 24 VAC Class 2 Only CONTROL RJ45 Ethernet Connector ALARMS 1 Alarm 1 Blue 2 Alarm 2 Violet 3 Alarm 3 Gray 4 Common White 12 POWER WIRING Two plug in wall transformers are included with the housing Use one to provide power for the heater and blower in the housing and the other for the camera Determine where the transformers will be located then run two sets of power wires into the wall mount bracket Four total power wires Use the chart below to determine the correct gauge of wire needed based on the length of the run and the 30vA power line 24 VAC Wiring Distances The following are the recommended maximum distances for 24VAC with a 10 voltage drop 10 is generally t
5. Product Instructions 25734 aS T p TI COMMUNICATIONS Before attempting to connect or operate this product 81 IN6215 please read these instructions completely 06 01 07 IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the unit is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the unit and in the operating instructions should be adhered to 4 Follow Instructions All operating and user instructions should be followed 5 Electrical Connections Only a qualified electrician should make electrical connections 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Cable Runs All cable runs must be within permissible distance 8 Mounting This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit Accordingly a The installation should be made by a qualified installer b The installation should be in compliance with local codes c Care should be exercised to select suitable hardware to install the unit taking into account both the composition of the mounting surface and the weight of the unit Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installati
6. al network cameras See specific instruction for the model that matches the unit you have aBa Installing the Axis 213 Camera 1 Install the camera onto the quick release bracket using 2 10 32 x 3 8 screws and star washers provided in the packet 2 In the kit there are 8 aluminum spacers 4 1 and 4 2 Thread 2 spacers 1 1 and 1 2 on top of each of the 4 2 spacers that are already located on the base bracket inside the housing Attach cameras using these 2 holes f A spacers 3 Then start 3 8 32x3 8 phillips head screws onto the 3 2 inch spacers inside the housing Be sure to place the screws so that they line up with the 3 open slots on the quick release bracket Installing Axis 213 Camera cont 4 Mount the camera assembly in the housing sliding the 3 open screw slots over the 3 screws in the housing Slide the bracket forward then tighten the captive screw on the bracket Captive Screw CAMERA POWER of the camera Connect the power plug and the ethernet cable to the back CONTROL RJ45 Ethernet Connector ALARMS 1 Alarm 1 Blue 2 Alarm 2 Violet 3 Alarm 3 Gray 4 Common White 3 screws in housing Power Connection Reference Only 12 VDC Installing Axis 214 Camera Attach cameras using these 3 holes 3 Place 3 8 x 32 x Phillips head screws on the top of the spacer as show
7. at will be needed during installation put it aside Picture 2 Power 24VAC Class 2 Only Teflon Tape 52 watts at 24 VAC accessories Heater 50 watts Blower 2 watts Picture 2 NOTE This unit is designed for operation in an upright position Installing the unit upside down may cause damage to the internal equipment and will void the warranty GENERAL INSTRUCTIONS 3 Open the dome assembly box Note there is a protection film on the dome DO NOT REMOVE the film until the product is fully assembled and installed This film protects the dome from scratches during installation Picture 3 Tools Required 100 Flat Head Screwdriver Phillios Head Screwdriver Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit ASSEMBLING THE PRODUCT Picture 3 1 Remove the contents of the box onto a table The larger 4 There is a safety lanyard that is attached to the inside of the subassembly box is the housing assembly The smaller housing assembly Remove the phillios head screw on the subassembly box is the dome assembly Picture 1 trim ring assembly and then attach the lanyard to the trim ring with the phillips head screw Picture 1 5 The safety lanyard is now attached to the housing Picture 5 Attach Lanyard to Trim Ring Picture 5 Listed on the following pages are the specific instructions for each of the individu
8. he maximum allowable voltage drop for AC powered devices Wire Gauge Total vA consumed 22 20 18 16 14 12 10 30 65 90 130 225 350 525 830 50 35 56 90 143 228 362 576 Maximum distance from transformer to housing The unit is setup with 2 individual power inputs 1 Accessory Power yellow and green wire 2 Camera Power red and orange If you wish to provide a single power transformer it is recommended that 1 Be certain that you know the total power consumption of the housing Heaters 25 watts Blowers 2 watts camera pan tilt not supplied 213 24 watts 13Vdc 214 14 watts 12Vdc 231D 232D 25 watts 24Vdc 2 Check the supplied wiring chart to be sure that you have the proper gauge wire for the distance that you intend to run your power wires 3 Bring power to the 3 and 4 position of the power connector yellow and green wire 4 Two jumpers are provided in the housing packet Jumper from the 1 position to the 34 position and from the 2 position to the 4 position of the terminal block Be careful not to short between the yellow and green wires Add 2 jumpers for single power input CONNECTING THE TRANSFORMERS Figure 2 Determine which transformer will be attached to the camera Attach the red and orange wires to the terminal points on the transformer For the transformer which will be used for the heater and blower attach the yel
9. illips head screwdriver remove the 4 machine screws holding the power board to the base bracket Machine screws 4 Installing Axis 231D 232D Camera cont 7 Locate the connector block Then start 3 8 32x3 8 phillips head screws onto the 3 2 spacers inside the housing Be sure to place the screws so that they line up with the 3 open slots on the quick release bracket the screws on the bottom of the camera see diagram below 3 8 32 x 3 8 screws which is included with the camera Then located the connector block bracket which is included with the housing Attach the block to the bracket as shown in the following diagram Use the M3 screws and washers that are located in the housing packet Attach the connector block assembly to the q 10 Make wiring connections to connector block assembly per housing using 1 6 camera instructions 32x3 8 screw and star washer located in the Wiring Connections housing packet aes Camera Power 24VAC Red 2 Camera Power 24VAC Orange CONTROL RJ45 Ethernet Connector ALARMS 1 Alarm 1 Blue 2 Alarm 2 Violet 3 Alarm 3 Gray 4 Common White 13 Attach the Installing Axis 231D 232D Camera dtc cont assembly to the housing by 11 To manage the input cable running from the connector sliding the 3 block to the camera use the 2 cable tie mounts and OPEN SCIEN cable ties that are located in
10. low and green wires to the terminal points NOTE You may attach wires to either terminal however MAKE SURE THAT THE TRANSFORMERS ARE ATTACHED TO THE PROPER CONNECTION ON THE HOUSING Accessory Power Green Yellow Accessory Power n Camera Power Orange Red One Power Supply for both Camera and Accessory Power 52 watts VA 24 VAC Class 2 Only NOTE In this combination run power to the camera connector then run jumper wires not provided to the accessory side of the connector Exploded View for Replacement Paris a h Replacement Parts List Part Number Description 1 RPFD7015 Lower Trim Ring 2 FD7T Tinted Replacement Capsule DAC Clear Replacement Capsule 3 RPFD703 Dome Clamping Bracket 4 RPFDO72 24 Vac Heater 5 RPFDO80 12 Vdc Blower Used In 24v Housings 6 RPFDO60 Camera Bracket 7 RPRH707 Connection Pcb 8 RPFD040 Housing Hardware 9 RPFD709 Housing Top 16 RPFD711 Pendant Mount Bracket 14
11. n above Be sure to place the screws so that they line up with the open slots on the mounting plate 4 Slide the mounting plate with camera into position on top of spacers Secure 3 screws and captive fastener 1 Install the AXIS 214 camera to the 2685 mounting plate using the 3 3mm x 12mm bolt and lock washers provided 2 The AXIS 214 camera requires 1 of spacing for optimal position within the housing Use the 4 1 spacers provided in the packet Installing Axis 231D 232D Camera 1 Install the camera onto the quick release bracket Loosen one of the screws on the bottom of the camera see diagram below Loosen screw Place quick release bracket onto the bottom of the camera making sure that the 3 locking buttons line up with the keyhole slots in the Q R bracket Also make sure the screw that you loosened up in the previous step lines up with the slot located next to the captive insert Keyhole slots Locking buttons 3 Turn the camera counter clockwise Locking screw Captive insert 4 When the locking buttons hit the end of the keyhole slots Tighten the locking screw Then put the camera assembly aside Locking screw 5 Since the 231D 232D camera operates on 24vac the power board that is located inside the housing is not needed The remove the power board start by loosening the screws on the terminal block and disconnect the orange and red wires With a Ph
12. on is intact Failure to comply with the foregoing could result in the unit separating from the support structure and falling with resultant damages or injury to anyone or anything struck by the falling unit WARRANTY INFORMATION Videolarm Incorporated warrants that products sold hereunder shall be fit for the ordinary purpose for which said products are intended and shall be free from defects in material and workmanship for a period of two years from date of sale to buyer Videolarm makes no other warranty of any kind with respect to this product whether expressed or implied including without limitation the implied warranty of fitness for a particular purpose In the event of a breach of the above warranty Videolarm shall at its option repair or replace said product This is Videolarm s sole obligation under this warranty In no event shall Videolarm be liable for any incidental or consequential damages as defined in section 2 715 of the Uniform Commercial Code by a breach of this warranty Videolarm shall repair or replace defective products upon shipment of products prepaid to Videolarm Inc 2525 Park Central Blvd Decatur GA 30035 Repairs made necessary by reason of accident misuse or normal wear shall be charged at Videolarm s standard rate This warranty gives you specific legal rights and you may also have other rights which vary from state to state SAFETY PRECAUTIONS A CAUTION RISK OF ELECTRIC SHOCK
Download Pdf Manuals
Related Search